User Manual

13
> Network Functions > Specifications > Advanced Setup > Listening Modes
Troubleshooting Supplementary Information, etc�|
> Basic Manual
■ 4� Level Calibration
Setting Item Default Value Setting Details
Front Left 0 dB Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Center 0 dB Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Front Right 0 dB Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Height Left 0 dB Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Height Right 0 dB Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Surround Right 0 dB Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Surr Back Right 0 dB Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Surr Back Left 0 dB Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Setting Item Default Value Setting Details
Surround Left 0 dB Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Subwoofer 0 dB Select a value between "−15 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
■ 5� Dolby Enabled Speaker
Setting Item Default Value Setting Details
Dolby Enabled
Speaker to
Ceiling
6.0 ft/1.80 m Set the distance between the Dolby Enabled
Speaker and the ceiling. Select between "0.1
ft/0.03 m" to "15.0 ft/4.50 m" (0.1 ft/0.03 m units).
•
The unit of distance (ft/m) shown is the unit
selected for use in "Distance".
AccuReflex Off You can enhance the reflection effect of Dolby
Enabled Speakers from the ceiling.
"Off": When this function is not to be used
"On": When this function is to be used
•
This setting can be selected when "Configuration" - "Height Speaker" is set to "Dolby Speaker".
■ 6� Equalizer Settings
You can adjust the output volume of the range of each connected speaker. You can adjust
the volume of the different sound ranges for each of the speakers. You can set three
different equalizers in Preset 1 to 3. You can select up to five bands for the Subwoofer and
nine bands for all other speakers.
Setting Item Default Value Setting Details
Front 0 dB After selecting the speaker frequency from
between "25 Hz" and "16 kHz" with the cursors
/
, adjust the volume of that frequency between
"−6 dB" and "＋6 dB" with / .