Product Sheet

Stable high-current power delivery
Dynamic changes in music cause impedance to fluctuate,
placing huge loads on the amp. If it can’t meet power
demands, sound breaks up. Onkyo’s WRAT employs a
high-output EI transformer, 10,000 µF customized audio
capacitors, and a low-impedance
drive. As well as achieving more
involving and musical sound,
low-negative-feedback
amplifier circuits with discrete
transistors deliver deep and
punchy bass thanks to wide
frequency response covering
10 Hz–100 kHz.
Hi-fi-grade digital board with Wolfson
®
DAC
Digital sources are decoded by a premium Wolfson
WM8718 DAC on the A-9130’s digital audio board. This
D/A converter is frequently installed on top-shelf audio
components thanks to exceedingly good performance
and supports 192 kHz/24-bit audio playback. TOSLINK or
coaxial digital audio inputs are also ready to amp your TV
entertainment, bringing powerful hi-fi sound to movies, games,
sporting events, and live concerts. When an analog input signal
is detected, the digital audio board shuts down automatically
to reduce potential interference on the signal.
Phase Matching Bass Boost enriches sound
at low volume
Most pre-main amps have a loudness button designed to
boost low-mid frequency sound. However, conventional
designs are prone to phase-shift, which degrades the clarity of
the vocal frequency band. Onkyo’s Phase Matching Bass Boost
function eliminates phase-shift between low- and mid-range
frequency bands above 300 Hz. Bass response is enhanced
without compromising vocal clarity, and that’s something
especially useful when playing music at low volume where bass
and high-frequency sounds are more difficult to hear.
Direct Mode brings you closer to the source
Direct Mode bypasses tone and PM Bass circuitries. In
combination with a refined amp circuit design, signal-path-
lengths have been significantly reduced in comparison to the
A-9030 for even more accurate and faithful sound. Enjoy
end-to-end analog music reproduction from turntable to
speakers, and recapture the atmosphere of the original
recording with any connected source.
Sounds clearer at low volumes
When playing music at low volume, the signal normally drops
close to the component’s noise floor. The signal picks up
noise, which is amplified, and the result is muffled sound.
To avoid this, the A-9130 features Optimum Gain Volume
Circuitry, which attenuates the signal by less than half the usual
amount. The signal never approaches the noise floor so you
can enjoy clearest sound at low volume.
Thick and rigid chassis tames resonance
Every hi-fi component generates electromechanical resonance.
This vibration translates into signal noise, and that impacts
on the sound coming out of your speakers. To combat the
negative effects of vibration, the A-9130 features a rigid chassis
that’s fabricated from 1.6 mm-thick steel. Working together
with large, wide-spaced insulators, unwanted resonance is
virtually eliminated.
New fine display shares info clearly
A new display panel boasts fine text resolution, making it
easier to read at a distance than single bulbs. It shows active
selected input at a glance.
Quality speaker-posts make
perfect contact
Speaker cables with your choice
of terminal are firmly secured by
high-quality speaker binding
posts. Each wide-spaced
non-magnetic post prevents
interference and features a large,
easy-to-grip transparent knob.
A-9130
Integrated Stereo Amplifier
SPECIFICATIONS
Due to a policy of continuous product improvement, Onkyo reserves the right to change specifications and appearance without notice. WRAT is a trademark of Onkyo Corporation. All other trademarks and registered trademarks are the property of their respective holders.
NPR No. 18N18 07/18
http://www.onkyo.com/
Copyright © 2018 Onkyo Corporation. All rights reserved.
Amplifier Section
Power output 60 W + 60 W (4 Ω, 20 Hz–20 kHz,
0.5% THD, 2-ch driven, IEC)
Dynamic power 260 W (3 Ω, Front)
220 W (4 Ω, Front)
130 W (8 Ω, Front)
THD+N (Total Harmonic Distortion + Noise)
0.04% (8 Ω, 1 kHz, half power)
Input sensitivity and impedance
Line 200 mV/47 kΩ
Phono MM 4 mV/47 kΩ (IHF-A)
Rated RCA output level and impedance
0.2 V/2.3 kΩ (Line Out)
1 V/ 500 Ω (Subwoofer Pre-Out)
Phono overload 70 mV (MM, 1 kHz, 0.5%)
Frequency response 10 Hz–100 kHz/+1 dB, -3 dB (Direct Mode)
Tone control ±10 dB, 100 Hz (Bass)
±10 dB, 10 kHz (Treble)
Signal-to-noise ratio 106 dB (IHF-A, Line In, Speaker Out)
81 dB (IHF-A, Phono In, Speaker Out)
Speaker impedance 4–16 Ω
General
Power supply AC 220–230 V, 50/60 Hz
Power consumption 150 W
Standby power consumption
0.2 W
No-sound power consumption
18.3 W
Dimensions (W x H x D) 435 x 129 x 330 mm
Weight 8.0 kg
CARTON
Dimensions (W x H x D) 572 x 252 x 419 mm
Weight 10.5 kg
Supplied Accessories
• Instruction manual • Remote controller • AAA (R03) batteries x 2*
*Not included with Chinese model variant.
Text on amplifier may vary with region.
Conventional Bass Boost
Phase Matching Bass Boost
Input
Output
REGULAR CIRCUIT
DIRECT MODE