Specification Sheet

ManualsBrandsOneSpace ManualsChairsBig and Tall Executive Office Chair - Leather with Mesh Back - Black - Taft Series

Table Of Contents

Blank Page

For fastest service on claims, requests for

replacement parts, or questions please visit our website at

www.comfortproducts.net/support

e-mail: customerservice@comfortproducts.net

Keep your sales receipt as documentation of your ownership.

CUSTOMER SERVICE

OneSpace is a Trademark of Comfort Products, Inc.

™

SUPPLIER CODE: BJTJ

TAFT MESH BACK OVERSIZE 500LB CAPACITY EXECUTIVE CHAIR

MODEL 60-5605T

ASSEMBLY INSTRUCTIONS

Summary of content (8 pages)

PAGE 1
™ OneSpace is a Trademark of Comfort Products, Inc. ASSEMBLY INSTRUCTIONS MODEL 60-5605T SUPPLIER CODE: BJTJ TAFT MESH BACK OVERSIZE 500LB CAPACITY EXECUTIVE CHAIR CUSTOMER SERVICE For fastest service on claims, requests for replacement parts, or questions please visit our website at www.comfortproducts.net/support e-mail: customerservice@comfortproducts.net Keep your sales receipt as documentation of your ownership.
PAGE 2
CONTENTS ITEMS ARE NOT SHOWN TO SCALE. PARTS LIST HARDWARE KIT STOCK # 61-5605THA PART DESCRIPTION STOCK# 1 Back Cushion 61-5605TBC 1 2 Seat Cushion 61-5605TSC 1 3 4 Armrest (right) Armrest (left) QTY. 61-5605TRA PART DESCRIPTION QTY. A 5/16 x 1 in. 2 B 5/16 x 1,1/2 in. 2 C 5/16 x 1,1/4 in. 4 D 5/16 x 1,3/4 in.
PAGE 3
ASSEMBLY INSTRUCTIONS STEP 1 STEP 2 Insert the casters (8) into holes of the star base (7). Insert the seat post (6) into the center hole of the star base (7). Align the seat plate (5) over the pre-drilled holes under the seat cushion (2) (NOTE the position of the seat plate handle to the seat cushion FRONT arrow). Attach the seat plate (5) to the seat cushion (2) using two screws (A) and two screws (B) as shown. Tighten securely with the allen wrench.
PAGE 4
ASSEMBLY AND FUNCTION INSTRUCTIONS STEP 5 STEP 6 Align the back cushion (1) with the holes in the armrests and secure it with four screws (D). Fully tighten the screws from step 4. Place four screw caps (F) over the screws at the bottom of the arms. Place the two arm covers (G) over the round sections on the arms and rotate them clockwise as shown below. 1 D TO ADJUST TILT TENSION TO ADJUST SEAT HEIGHT Reach under the front center of the chair seat and grasp the round black tension knob.
PAGE 5
FUNCTION INSTRUCTIONS TO OPERATE TILT LOCK While seated, reach underneath the right side of chair and locate the handle. Slide the handle all the way out towards the right (away from the seat). When the handle is in this position, leaning back will cause the chair to tilt backwards. To lock the chair in the upright (vertical) position, sit in the chair, and push the handle in to the left (towards center of seat). Right handle: * Pull outward to allow tilting * Push inward to lock the tilt.
PAGE 6
FREQUENTLY ASKED QUESTIONS • WHERE DO I FIND THE MODEL NUMBER AND SUPPLIER CODE FOR MY CHAIR? The chair model number and supplier code is located on a sticker underneath the seat cushion, and on the front page of your instruction manual. • HOW DO I ORDER REPLACEMENT PARTS? WHEN AM I GOING TO RECEIVE THEM? covered under warranty, there is no charge for replacement parts. We normally ship replacement parts within 48 hours. • HOW DO I ADJUST THE SEAT HEIGHT? Refer to page 4.
PAGE 7
• WHAT IS THE WARRANTY LENGTH? register your warranty. • HOW IS THE WARRANTY VALIDATED? Your warranty time period is validated by the purchase date on your original purchase receipt. (Please note that the warranty can not be validated without your original purchase receipt). • WHAT IS THE WEIGHT LIMIT ON MY CHAIR? The 60-5605T chair has been tested to meet BIFMA standards, and has a weight limit of up to 500 lbs. SAFETY AND MAINTENANCE • • • • • • • DO NOT stand on the chair.
PAGE 8
TOOLS NEEDED: (1) Newspaper or cardboard for work area, (2) Silicone lubricant (such as WD40),(3) Rubber Mallet FIGURE A INSTRUCTIONS: 1.) Spread newspaper or cardboard on your work surface. 2.) Turn your chair on its side. 3.) Spray lubricant around the center post where connected to your 5-star base. 4.) Remove casters (wheels) from base. 5.) Use the rubber mallet and bang on the center post, directly in the center of the 5-star base (Figure A). These two parts are engaged by pressure alone.