User's Manual

Name: ONEBOT Educational Mini Robot
Model: OBEDU09AIQI
Gross weight: 1160g
Input voltage: 3V
Input current: 1.0A
Wireless connectivity: Bluetooth 4.1
Materials: ABS and PC
Ages: 6 years+
Storage temperature: -20°C ~ 45°C (-4°F ~ 113°F)
Operating temperature: -10°C ~ 45°C (14°F ~ 113°F)
Specifications
1. Search “ONEBOT Kids” in the application store or scan the QR code below to download
ONEBOT Kids app.
3. Building courses can be acquired from APP.
ONEBOT Educational Mini Robot
User Manual
Precautions
Do not short circuit.
Do not crush or puncture.
Do not dismantle the electronic components. Remove the baeries from the baery cartridge
if the product will not be used for a long time.
Regularly check for any damage to cord, plugs, enclosure and other parts. And they must not
be used until the damage has been fully repaired.
Avoid direct sunlight. This product can be cleaned with water or a damp cloth. Please keep
the pieces clean and dry.
Do not expose the product to sunlight, fire, heat or environments where temperature is
above 60°C (140 °F).
Made in China
Manufactured by: Beijing AIQI Technology Co., LTD.
Thank you for choosing the ONEBOT Educational Mini Robot
Address: Room.D1203, The11thfloor, BlockD,No.9Shangdi3rdSt.,
HaidianDistrict,Beijing, 100085, China
Read this manual carefully before use, and retain it for future reference
Baery Cartridge ×2 Intelligent Brick ×2
Motors×4
Color sensor×2
Block Packs ×7 User Manual
Baery Installation
The ONEBOT Educational Mini Robot requires two AA baeries. Follow the steps below to install:
Align location hole
Open the baery cartridge lid by pushing in the direction indicated on the lid.
The installing and uninstalling of baeries shall always be done by an adult.
This product requires two AA baeries.
Non-rechargeable baeries cannot be recharged.
Rechargeable baeries must be charged under adult supervision.
Rechargeable baeries must be removed from the product before recharging.
Different types of baeries or new and used baeries are not to be mixed.
The supply terminals are not to be short-circuited.
Baeries must be placed according to their correct polarity.
Remove exhausted baeries from the product.
Accessories
Product Overview
1. Baery Cartridge
2. Intelligent Brick
3. Device
Transmission
Sha
Puzzle
Connector
Magnetic Port
Puzzle
Connector
Magnetic Port Restore
Factory Seings
Controller
Master Indicator
RESET
Magnetic PortBaery Cartridge
Switch
Baery Lid Direction
Indicator
Location Hole
Restore
Factory Seings
Correctly Powering On/Off
Power On: Turn on the baery cartridge, and then the intelligent brick's light is on with an
audio prompt.
Connect the baery cartridge to the intelligent brick aer installing the baeries.
Power Off: Turn off the baery cartridge, and then the intelligent brick's light is off with out
an audio prompt.
Installing the ONEBOT Kids
2. Connect to the ONEBOT Kids.
Connect the baery cartridge and the intelligent brick. Ensure that the baeries have been
properly installed into the cartridge and turned on. Open up the ONEBOT Kids app and turn
on Bluetooth. Tap on the Bluetooth icon in the upper le corner of the main screen. Search
for discoverable Bluetooth devices, and tap on the discovered device to connect to the
ONEBOT Kids.
Install the two AA baeries in accordance with the positive and negative polarity markings
on the boom of the baery cartridge and baeries.
Place the baery lid correctly on the baery cartridge and push the lid into place. Check
that the location hole is correctly aligned.
Read this manual carefully before use, and retain it for future reference
ONEBOT Educational Mini Robot
User Manual
Android 4.4.0 and above
iOS 9.0 and above
Wheels×6
FCC Statement
This device
complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and(2) This device must accept any interference received, including interference
that may cause undesired operation.
Aention that changes or modification not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential isnallation. This product generates, uses,
and can radiate radio frequency energy and, if not installed and used in acordance with the
instructions, may cause harmful interference to radio communications, However, there is no
guarantee. that interference will not occur in a particular insallation. If this product does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit diferent from that to which the receiveris
connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC ID: 2ALJ6-OBEDU09AIQI
IC Statement
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference,
and (2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisee aux deux conditions suivantes : (1) L'appareil ne
doit pas produire de brouillage, et (2) L'utilisateur de l'appareil doit accepter tout brouillage
radioelectrique subi, meme si le brouillage est susceptible d'en compromere le fonctionnement.
IC ID: 25212-OBEDU09AIQI
CAN ICES-3(B)/NMB-3(B)