User's Manual

ManualsBrandsOne World Technologies ManualsElectronicsGDO200 main unit

31 - English

Top

Screw

Bottom

Screw

INSTALLING THE OUTDOOR KEY PAD

See Figures 58 - 60.

Locate the following items:

Outdoor Key Pad

Screws (need size)

WARNING:

Do not use garage door opener if keypads or remotes

do not start and stop the motor. An opener that cannot

be controlled with a keypad or remote is dangerous,

can result in death or serious personal injury, and must

be repaired.

WARNING:

Make sure the key pad is mounted high enough to prevent

unauthorized activation of the garage door opener. It

should be placed at least 5 feet above the floor so that

it is inaccessible to children. Unauthorized activation of

the opener can result in death or serious personal injury.

WARNING:

Do not start or stop the garage door opener if there is a

person or object in the path of the door, the door has not

been properly balanced, or if you cannot see the doorway.

Failure to follow these instructions can result in death or

serious personal injury.

Find desired location outdoors and in sight of the garage

door.

NOTE: The key pad should be at least 5 feet above the

floor so it is inaccessible to children.

Use a pencil to mark screw hole placement and install

top screw.

Place the wide portion of the key hole over the head of

the top screw.

Slide the keypad down until the top screw is inside the

narrow portion of the key hole.

Remove the battery cover.

Use a level to be sure the keypad is in a vertical position,

then install bottom screw into the screw hole.

Install 9-volt battery.

Replace battery cover.

For programming instructions, see Programming the

Outdoor Keypad in the Operations section.

Fig. 59

Fig. 60

INSTALLATION

Key

Hole

Battery

Cover

Battery

Screwdriver

Pencil

Outdoor

Keypad

Fig. 58

Screw

Hole

Summary of content (18 pages)

PAGE 1
INSTALLATION INSTALLING THE OUTDOOR KEY PAD See Figures 58 - 60.  Locate the following items: Outdoor Keypad Outdoor Key Pad Pencil Screws (need size) WARNING: Do not use garage door opener if keypads or remotes do not start and stop the motor. An opener that cannot be controlled with a keypad or remote is dangerous, can result in death or serious personal injury, and must be repaired. Key Hole Screwdriver Top Screw WARNING: Fig.
PAGE 2
OPERATION WARNING: Do not allow familiarity with products to make you careless. Remember that a careless fraction of a second is sufficient to cause death or serious injury. WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious death or personal injury.
PAGE 3
OPERATION CHARGING A BATTERY PACK  Depress latches to release and remove the module. See Figure 62. Battery packs are shipped in a low charge condition to prevent possible problems. Therefore, you should charge them before first use. If the garage door opener does not charge the battery pack under normal circumstances, return both the battery pack and garage door opener to your nearest repair center for electrical check.
PAGE 4
OPERATION  Connect the garage door opener to an AC power supply. ALIGNING THE SAFETY SENSORS See Figure 65. NOTE: Make sure the power supply is normal household voltage, 120 volts, AC only, 60 Hz WARNING: DO NOT operate the garage door opener unless the safety sensors are installed and working correctly. Failure to properly install and ensure that the safety sensors are working correctly can result in death or serious personal injury.
PAGE 5
OPERATION SAFETY SENSOR DIAGNOSTIC FEEDBACK LED FUNCTIONS RED LED (TRANSMITTER) GREEN LED (RECEIVER) ON ON PROBLEM No problem indicated SOLUTION No action required Garage door operator is unplugged or Connect to power supply or charge the battery is depleted the battery pack Wires from garage door operator may Replace damaged or broken wires be damaged OFF OFF Wires not connected Connect wires to garage door operator Wires connected to the wrong terminal Connect wires to the correct terminal One o
PAGE 6
OPERATION SETTING THE DOOR TRAVEL LIMITS See Figures 66 - 73. DANGER: Ensure that the safety sensors are installed and working properly. Without the proper safety devices in place, a closing garage door could kill or seriously injure someone in its path. The console on your garage door opener makes it easy to set the open and close positions of your door. The opener will automically sense the weight of your door and provide the force required to open and close it.
PAGE 7
OPERATION NOTICE: Do not open or close the garage door using the indoor keypad or remotes until the travel limits have been properly set. Doing so could cause severe damage to the garage door or the garage door operator. Correct (Fully Open Position) Before setting the travel limit:  Pull the emergency release rope down and manually open the garage door until the carriage (trolley) engages the bullet. To set the travel limit for the open position:  Open the console door.
PAGE 8
OPERATION To test the travel limits: NOTE: The garage door opener will not respond to the remotes or keypads until the travel limits have been tested.  Open the console door. Set  Press and release the UP button and ensure that the door moves to the programmed open position. The button will blink as the door moves then shine continuously once the door is in the open position. Down Up  Press and release the DOWN button to ensure that the door moves to the programmed down position.
PAGE 9
OPERATION TESTING THE AUTOMATIC REVERSAL SYSTEM See Figure 74.  Press and release the UP button to raise the garage door.  Place a 1-1/2 in. board (approx. the size of a 2x4 laid flat) on the garage floor beneath the door.  Press and release the DOWN button to lower the garage door. When the door strikes the board, it should reverse direction immediately. DANGER: Test the automatic reversal system every month and after any adjustments are made to the garage door travel limits.
PAGE 10
OPERATION USING THE INDOOR KEYPAD Activating and Deactivating DC Module Ports: See Figure 75.  To activate a DC module port, press the number on the indoor keypad corresponding with the desired port. For example, to activate module port #2 press NUMBER 2 on your keypad.  Install and wire the indoor keypad as described earlier in the Installation section.  To raise or lower the garage door, press and release the UP/DOWN button.
PAGE 11
OPERATION PROGRAMMING THE OUTDOOR KEYPAD See Figures 76 - 77.  Install outdoor keypad and battery as described earlier in the Installation section. Program  Open the garage door.  Press and hold the PROGRAM button on the garage door opener’s console until the LED lights on the bottom of the opener flash three times, indicating the console is in programming mode.  Open the cover on the outdoor keypad and press the ON/ PROGRAM button. The keypad will light up.
PAGE 12
OPERATION USING THE SMARTPHONE APP See Figure 79. WARNING: 8:08 AM 100% To reduce the risk of injury to persons – Only enable the Ryobi Garage Door Opener Module System App feature when installed with a sectional door. WARNING: Devices or features, such as the Ryobi Garage Door Opener Module System App, that allow you to open and close the garage without the garage door being in view should only be used with sectional garage doors.
PAGE 13
MAINTENANCE POWER SUPPLY CORD REPLACEMENT WARNING: Before inspecting, cleaning or servicing the machine, lower the garage door, shut off motor, wait for all moving parts to stop, disconnect unit from power supply, and remove all modules. Failure to follow these instructions can result in serious personal injury or property damage. WARNING: When servicing, use only identical replacement parts. Use of any other parts could create a personal injury hazard or cause product damage.
PAGE 14
MAINTENANCE PERIODIC MAINTENANCE SCHEDULE Each Week  Check the garage door operator, rail, brackets, door arms, track, and rollers for loose or damaged parts. Replace or tighten as needed. Each Month  Manually open and close the garage door. If the door does not move smoothly, binds, or is out of balance, have the garage door or door springs repaired by a qualified service person.  Test the automatic reversal system as described in the Installation section.
PAGE 15
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Garage door opener does not Battery is low in charge or Charge the battery or connect to power supply activate when indoor keypad is power supply not connected pressed Garage operator is locked Press the LOCK button on the indoor keypad to unlock the operator The wire connecting the Replace damaged or broken wires keypad to the operator has been damaged Circuit breaker is tripped Garage door operator activates, The carriage (trolley) is not but the garage d
PAGE 16
WARRANTY LIMITED WARRANTY STATEMENT One World Technologies, Inc., warrants to the original retail purchaser that this RYOBI™ brand garage door opener is free from defect in material and workmanship and agrees to repair or replace, at One World Technologies, Inc.’s discretion, any defective product free of charge within these time periods from the date of purchase.
PAGE 17
FCC COMPLIANCE WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 18
OPERATOR’S MANUAL / GARAGE DOOR OPENER MANUEL D’UTILISATION / GARAGE DOOR OPENER MANUAL DEL OPERADOR / GARAGE DOOR OPENER GD200 To request service, purchase replacement parts, locate an Authorized Service Center and obtain Customer or Technical Support: Visit www.ryobitools.com or call 1-877-205-5714 If any parts or accessories are damaged or missing, do not return this product to the store. Call 1-877-205-5714 for immediate service. Please obtain your model and serial number from the product data plate.