Data Sheet

ManualsBrandsON SEMICONDUCTOR ManualsRectifiersDiode bridge SOIC 4 100 V 0.

MB1S - MB8S — 0.5 A Bridge Rectifiers

Publication Order Number:

MB8S/D

October-2017, Rev. 2

MB1S - MB8S

0.5 A Bridge Rectifiers

Features

• Low-Leakage

• Surge Overload Rating: 35 A peak

• Ideal for Printed Circuit Board

• UL Certified: UL #E258596

Ordering Informations

Part Number Marking Package Packing Method

MB1S MB1S

SOIC-4 Tape and Reel

MB2S MB2S

MB4S MB4S

MB6S MB6S

MB8S MB8S

SOIC-4

Polarity symbols molded

or mark on body

Description

The MB family of bridge rectifiers is a 0.5 A rectifier fam-

ily that achieves high surge current absorption within a

very small foot print. Within its small 35 mm

form factor,

the MB family shines in its surge capability. In order to

absorb high surge currents, the design supports a 35 A

FSM

rating and a 5.0 A

Sec I

T rating. Devices in the

family are also rated to breakdown voltages of up to

1000 V. These features make the MB family ideal for

small power supplies that need a little extra surge capa-

bility.

For higher I

FAV

current ratings, lower profile packaging,

or lower V

values, explore the ON Semiconductor

MDB family of bridge rectifiers. For improved V

and

efficiency values in the MB package or even higher

surge capability, ask about ON Semiconductor’s

pending MBxSV family.

Summary of content (4 pages)

PAGE 1
Features Description • Low-Leakage The MB family of bridge rectifiers is a 0.5 A rectifier family that achieves high surge current absorption within a • Surge Overload Rating: 35 A peak very small foot print. Within its small 35 mm2 form factor, the MB family shines in its surge capability. In order to absorb high surge currents, the design supports a 35 A • Ideal for Printed Circuit Board • UL Certified: UL #E258596 4 SOIC-4 IFSM rating and a 5.0 A2Sec I2T rating.
PAGE 2
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Values are at TA = 25°C unless otherwise noted.
PAGE 3
Forward Current, IF [A] 10 1 0.1 0.01 0.4 35 0.8 1 1.2 Forward Voltage, VF [V] 1.4 10 30 T C = 100 º C 25 20 15 10 5 0 0.6 Figure 2. Forward Voltage Characteristics Reverse Current, IR [mA] Peak Forward Surge Current, IFSM [A] Figure 1. Derating Curve for Output Rectified Current TA = 25º C μs Pulse Width = 300μ 2% Duty Cycle 1 2 5 10 20 Number of Cycles at 60Hz 50 100 Figure 3. Non-Repetitive Surge Current 1 0.1 TA = 25 º C 0.
PAGE 4
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.