Data Sheet

ManualsBrandsON SEMICONDUCTOR ManualsOptoelectronics & DisplaysOpto-isolator - TRIAC SMD 4 Tr

FODM30XX — 4-Pin Full Pitch Mini-Flat Package Random-Phase Triac Driver Output Optocouplers

Publication Order Number:

FODM3053-NF098/D

October-2017, Rev. 2

FODM3011, FODM3012, FODM3022, FODM3023,

FODM3052, FODM3053

4-Pin Full Pitch Mini-Flat Package Random-Phase Triac

Driver Output Optocouplers

Features

• Compact 4-pin Surface Mount Package

(2.4 mm Maximum Standoff Height)

• Peak Blocking Voltage

– 250V (FODM301X)

– 400V (FODM302X)

– 600V (FODM305X)

• Safety and Regulatory Approvals:

– UL1577, 3,750 VAC

RMS

for 1 Minute

– DIN-EN/IEC60747-5-5, 565 V Peak Working

Insulation Voltage

Applications

• Industrial Controls

• Traffic Lights

• Vending Machines

• Solid State Relay

• Lamp Ballasts

• Solenoid/Valve Controls

• Static AC Power Switch

• Incandescent Lamp Dimmers

• Motor Control

Description

The FODM301X, FODM302X, and FODM305X series

consists of a GaAs infrared emitting diode driving a

silicon bilateral switch housed in a compact 4-pin mini-

flat package. The lead pitch is 2.54 mm. They are

designed for interfacing between electronic controls and

power triacs to control resistive and inductive loads for

115 V/240 V operations.

Functional Schematic Package Outlines

Figure 2. Package Outlines

MAIN

TERMINAL

MAIN

TERMINAL

ANODE

CATHODE

Figure 1. Functional Schematic

Summary of content (12 pages)

PAGE 1
Features Description • Compact 4-pin Surface Mount Package (2.4 mm Maximum Standoff Height) • Peak Blocking Voltage – 250V (FODM301X) – 400V (FODM302X) – 600V (FODM305X) • Safety and Regulatory Approvals: – UL1577, 3,750 VACRMS for 1 Minute The FODM301X, FODM302X, and FODM305X series consists of a GaAs infrared emitting diode driving a silicon bilateral switch housed in a compact 4-pin miniflat package. The lead pitch is 2.54 mm.
PAGE 2
As per DIN EN/IEC 60747-5-5, this optocoupler is suitable for “safe electrical insulation” only within the safety limit data. Compliance with the safety ratings shall be ensured by means of protective circuits. Parameter Characteristics < 150 VRMS Installation Classifications per DIN VDE 0110/1.89 Table 1, For Rated Mains Voltage I–IV I–III < 300 VRMS Climatic Classification 40/100/21 Pollution Degree (DIN VDE 0110/1.
PAGE 3
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. TA = 25°C unless otherwise specified.
PAGE 4
TA = 25°C unless otherwise specified. Individual Component Characteristics Symbol Parameter Test Conditions Device Min. Typ. Max. Unit EMITTER VF Input Forward Voltage IF = 10 mA All 1.20 1.50 V IR Reverse Leakage Current VR = 3 V, TA = 25°C All 0.
PAGE 5
1.8 1000 IDRM - LEAKAGE CURRENT (nA) VF - FORWARD VOLTAGE (V) VDRM = 600 V 1.7 1.6 1.5 1.4 TA = -40 °C 1.3 25 °C 1.2 100 °C 1.1 10 1. 0.9 1 10 100 10 1 0.1 -40 100 -20 IF - FORWARD CURRENT (mA) IFT (TA) / IFT (TA = 25 °C) 10 NORMALIZED TO TA = 25 °C 1 -20 0 20 40 60 20 40 60 80 100 Fig 4. Leakage Current vs. Ambient Temperature 80 100 TA - AMBIENT TEMPERATURE (°C) IFT(NORMALIZED) IH(NORMALIZED) IH (TA) / IH (TA = 25 °C) Fig 3. LED Forward Voltage vs. Forward Current 0.
PAGE 6
VDRM(NORMALIZED) = VDRM (TA) / VDRM (TA = 25 °C) TA = 25 °C NORMALIZED TO PWIN >> 100 µs 10 8 6 4 2 0 1 10 100 PWIN - LED TRIGGER PULSE WIDTH (µs) Fig 7. LED Current Required to Trigger vs. LED Pulse Width 1.4 NORMALIZED TO TA = 25 °C 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 -40 -20 0 TA = 25 °C 200 100 0 -100 -200 -300 -400 -3 -2 -1 40 60 80 100 Fig 8. Normalized Off-State Output Terminal Voltage vs.
PAGE 7
600 V (FODM3052) (FODM3053) 400 V (FODM3022) (FODM3023) 250 V (FODM3011) (FODM3012) RTEST Vdc R = 10 kΩ CTEST PULSE INPUT MERCURY WETTED RELAY APPLIED VOLTAGE WAVEFORM X100 SCOPE PROBE D.U.T. 1. The mercury wetted relay provides a high speed repeated pulse to the D.U.T. 2. 100x scope probes are used, to allow high speeds and voltages. 3. The worst-case condition for static dv/dt is established by triggering the D.U.T. with a normal LED input current, then removing the current.
PAGE 8
Rin 1 4 360 Ω 470 Ω HOT VCC 2 FODM3022 FODM3023 FODM3052 FODM3053 0.05 μF 39 Ω 3 240 VAC 0.01 μF LOAD GROUND In this circuit the “hot” side of the line is switched and the load connected to the cold or ground side. The 39 Ω resistor and 0.01μF capacitor are for snubbing of the triac, and the 470 Ω resistor and 0.05 μF capacitor are for snubbing the coupler. These components may or may not be necessary depending upon the particular and load used. Figure 13. Typical Application Circuit www.
PAGE 9
Temperature (°C) TP 260 240 TL 220 200 180 160 140 120 100 80 60 40 20 0 Max. Ramp-up Rate = 3°C/S Max. Ramp-down Rate = 6°C/S tP Tsmax tL Preheat Area Tsmin ts 120 240 360 Time 25°C to Peak Time (seconds) Proﬁle Freature Pb-Free Assembly Proﬁle Temperature Min. (Tsmin) 150°C Temperature Max. (Tsmax) 200°C Time (tS) from (Tsmin to Tsmax) 60–120 seconds Ramp-up Rate (tL to tP) 3°C/second max.
PAGE 10
Part Number Package Packing Method FODM3011 Full Pitch Mini-Flat 4-Pin Tube (100 units) FODM3011R2 Full Pitch Mini-Flat 4-Pin Tape and Reel (2500 Units) FODM3011V Full Pitch Mini-Flat 4-Pin, DIN EN/IEC60747-5-5 Option Tube (100 Units) FODM3011R2V Full Pitch Mini-Flat 4-Pin, DIN EN/IEC60747-5-5 Option Tape and Reel (2500 Units) Note: The product orderable part number system listed in this table also applies to the FODM3012, FODM3022, FODM3023, FODM3052, and FODM3053 products.
PAGE 11
K0 P2 P0 t D0 E A0 W1 W B0 d F D1 P 2.54 Pitch Description Symbol Dimensions Tape Width W 12.00±0.4 Tape Thickness t 0.35±0.02 Sprocket Hole Pitch P0 4.00±0.20 Sprocket Hole Dia. D0 1.55±0.20 Sprocket Hole Location E 1.75±0.20 Pocket Location F 5.50±0.20 P2 2.00±0.20 Pocket Pitch P 8.00±0.20 Pocket Dimension A0 4.75±0.20 Pocket Hole Dia. B0 7.30±0.20 K0 2.30±0.20 D1 1.55±0.20 Cover Tape Width W1 Cover Tape Thickness d Max. Component Rotation or Tilt 9.
PAGE 12
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.