INSTRUCTION MANUAL Wrist Blood Pressure Monitor ENGLISH ESPAÑOL Model BP652
TABLE OF CONTENTS Before using the monitor Introduction........................................................................................................3 Safety information .............................................................................................4 Intended use ................................................................................................4 Operating the device ...................................................................................
INTRODUCTION Thank you for purchasing the OMRON BP652 Wrist Blood Pressure Monitor. Fill in for future reference. DATE PURCHASED: __________________ SERIAL NUMBER: ____________________ • Staple your purchase receipt here • Register your product on-line at www.register-omron.com The monitor is compact and easy-to-use at home, at work, and during travel. Perfect for people who frequently monitor their own blood pressure.
SAFETY INFORMATION INTENDED USE The device is a digital monitor intended for use in measuring blood pressure and pulse rate in adult patient population with wrist circumference ranging from 5 1/4 inches to 8 1/2 inches (13.5 cm to 21.5 cm). The device detects the appearance of irregular heartbeats during measurement and gives a warning signal with readings.
SAFETY INFORMATION Do not use the device in the area the HF surgical equipment, MRI, or CT scanner exists, or in the oxygen rich environment. Consult your physician before using the device for any of the following conditions: • If you have had a mastectomy. • Do not take measurements more than necessary. It may cause bruising due to blood flow interference. • People with severe blood flow problems or blood disorders as cuff inflation can cause bruising.
BEFORE TAKING A MEASUREMENT To ensure a reliable reading, follow these recommendations: 1. Avoid eating, drinking alcohol, smoking, exercising, and bathing for 30 minutes before taking a measurement. Rest for at least 5 minutes before taking the measurement. 2. Stress raises blood pressure. Avoid taking measurements during stressful times. 3. The cuff can be applied to your left or right wrist. 4. Measurements should be taken in a quiet place. 5. Position the unit at heart level throughout the measurement.
KNOW YOUR UNIT Main Unit: Wrist cuff Memory button Battery compartment START/STOP button Display Date/Time setting ( ) button Date/Time setting ( ) button Components: EN ES INSTRUCTION MANUAL GETTING STARTED Wrist Blood Pressure Monitor Model BP652 1883330-6A INTRODUCTION Wrist Blood Pressure Monitor Thank you for purchasing the OMRON BP652 Wrist Blood Pressure Monitor. Fill in for future reference.
UNIT DISPLAY Date/Time display Blood pressure level indicator (bar) Average reading symbol Positioning symbol Memory symbol Systolic blood pressure Positioning indicator Diastolic blood pressure Low battery symbol Heartbeat symbol (Flashes during measurement) Pulse display / Memory number Irregular heartbeat symbol Movement error symbol Deflation symbol 8
DISPLAY SYMBOLS HEARTBEAT SYMBOL ( ) The Heartbeat symbol flashes on the display at every heartbeat during the measurement. AVERAGE READING SYMBOL ( ) The Average Reading Symbol is displayed when you press the Memory button ( ). The most recent average reading appears on the display screen. IRREGULAR HEARTBEAT SYMBOL ( ) When the monitor detects an irregular rhythm two or more times during the measurement, the Irregular Heartbeat Symbol will appear on the display with the readings.
DISPLAY SYMBOLS 2013 ESH/ESC Guidelines for the management of arterial hypertension Definitions of hypertension by office and home blood pressure levels Office Home Systolic Blood Pressure ≥ 140 mmHg ≥ 135 mmHg Diastolic Blood Pressure ≥ 90 mmHg ≥ 85 mmHg These are from statistical values for blood pressure. WARNING Consult your physician for specific information about your blood pressure. Self-diagnosis and treatment using readings may be dangerous.
BATTERY INSTALLATION CAUTION Use only 1.5V “AAA” alkaline batteries with this device. 1. Press the hook of the battery cover and pull downward. 2. Install 2 “AAA” size batteries so the + (positive) and - (negative) polarities match the polarities of the battery compartment as indicated. 3. Replace the battery cover. NOTE: Make sure that the battery cover is securely in position.
BATTERY INSTALLATION BATTERY REPLACEMENT Low battery symbol When the Low battery symbol appears on the display, turn the monitor off and remove all the batteries. Replace with 2 new batteries at the same time. WARNING If battery fluid should get in your eyes, immediately rinse with plenty of clean water. Consult a physician immediately. WARNING Keep the batteries out of reach of young children. NOTES: • Turn the unit off before replacing the batteries.
SETTING THE DATE AND TIME Set the monitor to the current date and time before taking a measurement for the first time or after replacing the batteries. 1. TO START THE SETTING Press the Date/Time Setting button ( to adjust the date and time. The year flashes on the display. ) 2. SETTING THE YEAR Press the Date/Time Setting button ( to advance by one year. Press the Date/Time Setting button ( to set the current year. ) ) The month flashes on the display.
SETTING THE DATE AND TIME 4. SETTING THE DAY Press the Date/Time Setting button ( to advance by one day. Press the Date/Time Setting button ( to set the current day. The hour flashes on the display. 5. SETTING THE HOUR The time is set using AM or PM. Press the Date/Time Setting button ( to advance by one hour. Press the Date/Time Setting button ( to set the current hour. The minute flashes on the display. 6. SETTING THE MINUTE Press the Date/Time Setting button ( to advance by one minute.
APPLYING THE WRIST CUFF CAUTION Read all of the information in the instruction manual and any other literature in the box before operating the unit. CAUTION This device is intended for use in measuring blood pressure and pulse rate in the adult population. Do not use this device on infants or persons who cannot express their intentions. APPLYING THE CUFF ON THE LEFT WRIST 1. Roll up sleeve. Make sure your sleeve is not rolled up too tightly on your arm. This may constrict the flow of blood in your arm. 2.
APPLYING THE WRIST CUFF 4. Wrap the wrist cuff around your wrist. Do not apply over clothing. NOTES: • Make sure the wrist cuff does not cover the protruding part of the wrist bone on the outside of the wrist. • If the wrist cuff comes off, re-assemble as shown in the figure. APPLYING THE CUFF ON THE RIGHT WRIST When taking a measurement using the right wrist position the cuff as shown in the illustration.
TAKING A MEASUREMENT 1. Sit comfortably on a chair with your feet flat on the floor and place your elbow on a table in order to relax before starting blood pressure measurement. NOTES: • The distance from the top of your seat measuring to the top of the table you are sitting at, should be 12±2 inches (30±5 cm). If the distance measured between the top of your seat and table do not fall within this parameter, please correct your seat or table height.
TAKING A MEASUREMENT SETTING THE POSITIONING SENSOR Press and hold the button to reset the Positioning sensor. The Positioning sensor is set “on” as default. Press the START/STOP button to store the new setting. 2. Press the START/STOP button. All symbols appear on the display. Heart Zone Guidance-The monitor has a built-in Positioning sensor that is used as an aid in determining if the monitor is at the correct height.
TAKING A MEASUREMENT NOTE: Even if the device is not positioned properly and the Positioning indicator is orange, after 5 seconds the monitor will start the measurement and the wrist cuff will start to inflate.
TAKING A MEASUREMENT As the cuff inflates, the monitor automatically determines your ideal inflation level. This monitor detects your blood pressure and pulse rate during inflation. The Heartbeat Symbol ( ) flashes at every heartbeat. Remain still and do not move until the entire measurement process is completed. NOTE: To stop the inflation or measurement, push the START/STOP button. The monitor will stop inflating, start deflating, and will turn off. 3.
TAKING A MEASUREMENT WARNING Consult your physician for specific information about your blood pressure. Self-diagnosis and treatment using readings may be dangerous. Follow the instructions of your physician or licensed healthcare provider. WARNING DO NOT adjust medication based on readings from this blood pressure monitor. Take medication as prescribed by your physician. Only a physician is qualified to diagnose and treat High Blood Pressure. WARNING The monitor is not intended to be a diagnostic device.
USING THE MEMORY FUNCTION Every time you complete a measurement, the monitor stores the blood pressure and pulse rate in the memory. The monitor automatically stores up to 100 readings (blood pressure and pulse rate). When 100 readings are stored, the oldest record is deleted to save the most recent readings. AVERAGING FUNCTION The monitor calculates the average reading based on up to the three most recent readings taken within 10 minutes.
USING THE MEMORY FUNCTION NOTES: • The Memory number appears for a second before the pulse rate is displayed. The newest set is number “1”. • If the Positioning indicator is set to “on” before the measurement, the Positioning indicator is displayed with the readings. • The date and time are alternately displayed with the readings. • Press the Memory button ( ) repeatedly to display the next readings. • Press and hold the Memory button ( ) to display the readings faster. 3.
CARE AND MAINTENANCE To keep your digital blood pressure monitor in the best condition and protect the unit from damage, follow the directions listed below: Do not forcefully bend the cuff. Do not fold tightly. Clean the monitor with a soft dry cloth. Do not use any abrasive or volatile cleaners. Wipe clean on the surface of the cuff with a soft, moistened cloth with a dilution of neutral detergent. Do not allow any liquids inside the cuff. If a liquid gets in the cuff, dry the inside well.
ERROR INDICATORS SYMBOL CAUSE CORRECTION Wrist cuff not applied correctly. Apply the wrist cuff correctly. Refer to “Applying the Wrist Cuff”. Movement during measurement. Do not hold the wrist cuff. Remain still and do not talk during measurement. Refer to “Taking a Measurement”. Wrist cuff not applied correctly or movement during measurement. Apply the wrist cuff correctly. Refer to “Applying the Wrist Cuff”. Remain still and do not talk during measurement. Refer to “Taking a Measurement”.
TROUBLESHOOTING TIPS PROBLEM CAUSES AND SOLUTIONS Replace both batteries with new ones at the No power. No display appears on the unit. same time. Check the battery installation for proper placement of the battery polarities. Review the section “Battery Installation”. Readings appear too high or too low. Blood pressure varies constantly. Many factors including stress, time of day, how you wrap the cuff, where you position your wrist, may affect your blood pressure.
FCC STATEMENT FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
LIMITED WARRANTY Your BP652N Wrist Blood Pressure Monitor, excluding the batteries, is warranted to be free from defects in materials and workmanship appearing within 5 years from the date of purchase, when used in accordance with the instructions provided with the monitor. The above warranty extends only to the original retail purchaser. We will, at our option, replace without charge any monitor covered by the above warranty.
SPECIFICATIONS BP652N HEM-6300-Z LCD Digital Display Pressure: 0 to 299 mmHg, Pulse: 40 to 180 beats/min. Pressure: ±3mmHg or 2% of reading Pulse: ±5% of reading Automatic by electric pump Inflation: Automatic rapid deflation Deflation: Measurement Method: Oscillometric method 2 “AAA” alkaline batteries 1.
SPECIFICATIONS NOTES: • These specifications are subject to change without notice. • In the clinical validation study, the 5th phase was used on 85 subjects for determination of diastolic blood pressure. • This device has not been validated for use in pregnancy.
GUIDANCE AND MANUFACTURER’S DECLARATION OMRON Wrist Blood Pressure Monitor (BPM) Information for accompanying documents in the scope of IEC60601-1-2:2007 Important information regarding Electro Magnetic Compatibility (EMC) With the increased number of electronic devices such as PC’s and mobile (cellular) telephones, medical devices in use may be susceptible to electromagnetic interference from other devices.
GUIDANCE AND MANUFACTURER’S DECLARATION • The Essential Performance of the BPM is to measure a blood pressure and a pulse rate and using the memory function. The BPM may be interfered with by other equipment, even if that other equipment complies with CISPR EMISSION requirements. (Table 1) Guidance and manufacturer’s declaration – electromagnetic emissions OMRON BPM is intended for use in the electromagnetic environment specified below.
GUIDANCE AND MANUFACTURER’S DECLARATION (Table 2) Guidance and manufacturer’s declaration – electromagnetic immunity OMRON BPM is intended for use in the electromagnetic environment specified below. The customer or the user of this OMRON BPM should assure that it is used in such environment. Immunity test IEC 60601 Compliance Test level level Electromagnetic environment – guidance Floor should be wood, concrete, or ceramic tile.
GUIDANCE AND MANUFACTURER’S DECLARATION Immunity test IEC 60601 Compliance Test level level Electromagnetic environment – guidance <5 % UT (>95 % dip in UT) for 0.5 cycle Voltage dips, short interruptions and voltage variations on power supply inputlines IEC 61000-4-11 40 % UT (60 % dip in UT) for 5 cycles Not 70 % UT Applicable. (30 % dip in UT) for 25 cycles Not Applicable. <5 % UT (>95 % dip in UT) for 5 sec.
GUIDANCE AND MANUFACTURER’S DECLARATION (Table 4) Guidance and manufacturer’s declaration – electromagnetic immunity OMRON BPM is intended for use in the electromagnetic environment specified below. The customer or the user of this OMRON BPM should assure that it is used in such environment.
GUIDANCE AND MANUFACTURER’S DECLARATION Immunity test Radiated RF IEC 61000-4-3 IEC 60601 Compliance Test level level 3 V/m 80 MHz to 2.5 GHz Electromagnetic environment – guidance d = 1.2 P 80 MHz to 800 MHz d = 2.3 P 800 MHz to 2.5 GHz 3 V/m where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in meters (m).
GUIDANCE AND MANUFACTURER’S DECLARATION Note1: At 80 MHz and 800 MHz, the higher frequency range applies. Note2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects, and people. a b Field strengths from fixed transmitters, such as base stations for radio (cellular/ cordless) telephones and land mobile radio, AM and FM radio broadcast, and TV broadcast cannot be predicted theoretically with accuracy.
GUIDANCE AND MANUFACTURER’S DECLARATION (Table 6) Recommended separation distance between portable and mobile RF communications equipment and the OMRON BPM OMRON BPM is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
Manufactured for : OMRON HEALTHCARE Co., Ltd. Distributed by : OMRON HEALTHCARE, INC. 1925 West Field Court Lake Forest, IL 60045 U.S.A. www.omronhealthcare.com © 2014 OMRON HEALTHCARE, INC.
