Datasheet
9
Z
Dimensions (Unit: mm)
Mounting
Use M4 screws with plane washers and spring washers to mount the
Switch. Tighten each mounting screw securely to a torque of 1.18 to
1.47 N·m.
When mounting the Switch to a panel, use a tightening torque of 2.94
to 4.9 N·m for the hexagonal nuts on the actuator.
Terminals
Dimensions and Operating Characteristics
The models, illustrations, and graphics are for screw-terminal models (-B). The “-A” at the end of the model number for solder terminal models has been omitted. For
details of the terminals, see above.
Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
25.4
±0.1
Two, 4.2 dia. mounting holes or M4
12.5 dia.
+0.2
0
12.5 dia.
+0.2
0
13
+0.2
0
5
+0.2
0
Panel Mount Roller PlungerPanel Mount Plunger
Basic Models Split-contact Models
Note: With reverse action models (Z-15GM), the positions of NO and NC terminals are reversed.
Basic Models and Split-contact Models
General-purpose
COM NO NC
13
2
49.2
17.45
±0.2
Three, M4 × 5.5
Terminal screws
(with toothed
washer)
9.2
20 20
Screw Terminals (-B)
Appropriate terminal screw tightening torque: 0.78
to 1.18 N·m.
COM
NO
NC
1
2
3
11.9
25.4
±
0.1
6.4
49.2
17.45
±
0.2
Solder Terminal (-A) (“-A” is not included
in the model numbers.)
COM
NO
NC
NO
NC
17.45
±
0.2
Five, M3.5
×
5.5
terminal screws
(with toothed
washer)
5.6
23 17.1
11.9
Screw Terminals (Y-B)
Appropriate terminal screw tightening torque: 0.49
to 0.78 N·m.
Note: With reverse action models (Z-10FM), the
positions of NO and NC terminals are
reversed.
49.2
11.9
25.4
±0.1
23.3
±0.25
24.2
17.45
±0.2
OP
PT
2.3 dia.
2.3SR *
* Stainless-steel plunger
9.2
4.36 dia.
+0.1
-0.05
4.2
+0.075
-0.025
4.2 dia. hole
+0.075
-0.025
Pin Plunger
Z-15G-B Z-15E-B
Z-15H2-B Z-01H-B
Z-15H-B Z-10FY-B
Operating
Characteristics
Model Z-15G-B Z-15H2-B Z-15H-B Z-15E-B Z-01H-B Z-10FY-B
Operating force OF
Release force RF min.
Pretravel PT max.
Overtravel OT min.
Movement Differential MD max.
2.45 to 3.43 N
1.12 N
0.4 mm
0.13 mm
0.05 mm
1.96 to 2.5 N
1.12 N
0.3 mm
0.13 mm
0.005 to 0.008 mm
1.96 to 2.75 N
1.12 N
0.3 mm
0.13 mm
0.025 mm
6.12 to 7.85 N
1.12 N
0.8 mm
0.13 mm
0.13 mm
2.45 N max.
0.78 N
0.5 mm
0.13 mm
0.04 mm
4.46 to 7.26 N
1.12 N
0.8 mm
0.13 mm
0.1 mm
Operating Position OP 15.9±0.4 mm
49.2
11.9
25.4
±0.1
23.3
±0.25
24.2
17.45
±0.2
OP
PT
5.2 dia.
* Stainless-steel plunger (flat, 1R chamfered)
*
4 dia.
9 dia.
9.2
4.36 dia.
+0.1
-0.05
4.2
+0.075
-0.025
4.2 dia. hole
+0.075
-0.025
Z-15GS-B Z-15HS-B Z-01HS Z-10FSY-B
OF
RF min.
PT max.
OT min.
MD max.
2.45 to 3.43 N
1.12 N
0.4 mm
1.6 mm
0.05 mm
1.96 to 2.79 N
1.12 N
0.3 mm
1.6 mm
0.025 mm
2.45 N max.
0.78 N
0.5 mm
1.6 mm
0.05 mm
4.46 to 7.26 N
1.12 N
0.8 mm
1.6 mm
0.1 mm
OP 28.2±0.5 mm
Slim Spring Plunger
Z-15GS-B Z-01HS-B
Z-15HS-B Z-10FSY-B