Datasheet

17
Z
* The pin plungers of reverse-type models are continuously pressed by the actuator levers with compression coil springs and the pin plungers are freed by operating
the levers.
Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
49.2
11.9
25.4
±0.1
26.2
OP
FP
* Stainless-steel lever
t = 1 *
20.2
16.9
13.9
48.5R
9.5 dia. × 4
(plastic roller)
9.2
17.45
±0.2
4.2
+0.075
-0.025
4.2 dia. hole
+0.075
-0.025
4.36 dia.
+0.1
-0.05
Hinge Roller Lever
Z-15GW255-B
OF max.
RF min.
OT min.
MD max.
1.27 N
0.21 N
4 mm
1.6 mm
FP max.
OP
36.5 mm
30.2±0.8 mm
49.2
11.9
25.4
±0.1
26.2
Operating direction
OP
FP
* Stainless-steel lever
t = 1 *
20.2
34.1 max.
16.9
13.9
9.5 dia.
× 4
(plastic roller)
11.1R
31.9R
9.2
17.45
±0.2
4.2
+0.075
-0.025
4.2 dia. hole
+0.075
-0.025
4.36 dia.
+0.1
-0.05
Unidirectional Short Hinge Roller Lever
Z-15GW227755-B
OF max.
RF min.
OT min.
MD max.
1.77 N
0.49 N
2.4 mm
0.8 mm
FP max.
OP
43.6 mm
41.3±0.8 mm
49.2
11.9
25.4
±0.1
18.65
56R
17.45
±0.2
4.9
OP
FP
* Stainless-steel lever
t = 1 *
20.2
17.4
13.9
9.2
4.2
+0.075
-0.025
4.2 dia. hole
+0.075
-0.025
4.36 dia.
+0.1
-0.05
Reverse Hinge Lever *
Z-15GM55-B
OF max.
RF min.
OT min.
MD max.
1.96 N
0.27 N
5.6 mm
0.89 mm
FP max.
OP
23.8 mm
19±0.8 mm
49.2
11.9
25.4
±0.1
18.65
17.45
±0.2
OP
FP
* Stainless-steel lever
t = 1 *
20.2
17.4
13.9
18.5R
9.5 dia. × 4
(plastic roller)
9.2
4.2
+0.075
-0.025
4.2 dia. hole
+0.075
-0.025
4.36 dia.
+0.1
-0.05
Reverse Short Hinge Roller Lever *
Z-15GM2255-B
OF max.
RF min.
OT min.
MD max.
5.69 N
1.67 N
2 mm
0.28 mm
FP max.
OP
31.8mm
29.4±0.4mm
17.45
±0.2
9.5 dia. × 4
(plastic roller)
49.2
11.9
25.4
±0.1
18.65
OP
FP
* Stainless-steel lever
t = 1 *
20.2
17.4
13.9
40.6R
9.2
4.2
+0.075
-0.025
4.2 dia. hole
+0.075
-0.025
4.36 dia.
+0.1
-0.05
Reverse Hinge Roller Lever *
Z-15GM255-B
OF max.
RF min.
OT min.
MD max.
2.65 N
0.55 N
4 mm
0.64 mm
FP max.
OP
35 mm
30.2±0.8 mm