Datasheet

160 General-purpose Basic Switch Z
Note: 1. All drawings show the switches with screw terminals. For versions with solder terminals, remove the “-B” from the end of the part number.
2. Unless otherwise specified, all units are in millimeters and a tolerance of ± 0.4 mm applies to all dimensions.
49.2
11.9
25.4
±0.1
26.2
OP
FP
9.2
* Stainless-steel lever
t = 1 *
20.2
16.9
13.9
27.1R
9.5 dia.
×
4
(plastic roller)
17.45
±0.2
4.2
+0.075
-0.025
4.2 dia. hole
+0.075
-0.025
4.36 dia.
+0.1
-0.05
Short Hinge Cross Roller Lever
Z-15GW49-B
Z-15GW54-B (Lever Length: 48.7R) *
Model Z-15GW49-B Z-15GW54-B
OF max.
RF min.
OT min.
MD max.
170 gf
42 gf
2.4 mm
0.51 mm
100 gf
22 gf
4 mm
1 mm
FP max.
OP
33.3 mm
31±0.4 mm
37.3 mm
31±0.8 mm
* The external dimensions
of the actuator vary.
17.45
±0.2
4.2
+0.075
-0.025
4.2 dia. hole
+0.075
-0.025
4.36 dia.
+0.1
-0.05
49.2
11.9
25.4
±0.1
26.2
OP
FP
* Stainless-steel lever
t = 1*
20.2
16.9
13.9
50R
20 dia.
×
4
(plastic roller)
R2
9.2
Hinge Roller Lever
Z-15GW25-B
OF max.
RF min.
OT min.
MD max.
100 gf
21 gf
4 mm
1.6 mm
FP max.
OP
47.5 mm
41.2±0.8 mm
49.2
11.9
25.4
±0.1
26.2
Operating direction
OP
FP
* Stainless-steel lever
t = 1 *
20.2
34.1 max.
16.9
13.9
9.5 dia.
×
4
(plastic roller)
11.1R
31.9R
9.2
17.45
±0.2
4.2
+0.075
-0.025
4.2 dia. hole
+0.075
-0.025
4.36 dia.
+0.1
-0.05
Unidirectional Short
Hinge Roller Lever
Z-15GW2277-B
OF max.
RF min.
OT min.
MD max.
170 gf
42 gf
2.4 mm
0.51 mm
FP max.
OP
43.6 mm
41.3±0.8 mm
49.2
11.9
25.4
±0.1
18.65
56R
4.9
OP
FP
* Stainless-steel lever
t = 1 *
20.2
17.4
13.9
9.2
17.45
±0.2
4.2
+0.075
-0.025
4.2 dia. hole
+0.075
-0.025
4.36 dia.
+0.1
-0.05
Reverse Hinge Lever **
Z-15GM-B
OF max.
RF min.
OT min.
MD max.
170 gf
28 gf
5.6 mm
0.89 mm
FP max.
OP
23.8 mm
19±0.8 mm
49.2
11.9
25.4
±0.1
18.65
OP
FP
* Stainless-steel lever
t = 1 *
20.2
17.4
13.9
18.5R
9.5 dia.
×
4
(plastic roller)
9.2
17.45
±0.2
4.2
+0.075
-0.025
4.2 dia. hole
+0.075
-0.025
4.36 dia.
+0.1
-0.05
Reverse Short Hinge Roller Lever **
Z-15GM22-B
Z-10FM22Y-B
Z-15GM22-B Z-10FM22Y-B
OF max.
RF min.
OT min.
MD max.
538 gf
170 gf
2 mm
0.28 mm
650 gf
170 gf
2 mm
0.56mm
FP max.
OP
31.8 mm
29.4±0.4 mm
33 mm
29.4±0.4 mm
17.45
±0.2
4.2
+0.075
-0.025
4.2 dia. hole
+0.075
-0.025
4.36 dia.
+0.1
-0.05
49.2
11.9
25.4
±0.1
18.65
OP
FP
* Stainless-steel lever
t = 1*
20.2
17.4
13.9
9.5 dia.
×
4
(plastic roller)
40.6R
9.2
Reverse Hinge Roller Lever **
Z-15GM2-B
**The pin plungers of reverse-type models are continuously
pressed by the actuator levers with compression coil springs
and the pin plungers are freed by operating the levers.
Reverse-type models are highly vibration- and shock-resis-
tive because the pin plungers are normally pressed.
OF max.
RF min.
OT min.
MD max.
240 gf
56 gf
4 mm
0.64 mm
FP max.
OP
35 mm
30.2±0.8 mm