Datasheet
XW5T-P
9
Checking Connections
• After the insertion, pull gently on the wire to make sure that it will
not come off and the wire is securely fastened to the terminal block.
• To prevent short circuits, insert the stripped part of a stranded or
solid wire or the conductor part of a ferrule until it is hidden inside
the terminal insertion hole. (See the following diagram.)
3. Removing Wires from the Push-In Plus
Terminal Block
Use the following procedure to remove wires from the terminal block.
The same method is used to remove stranded wires, solid wires, and
ferrules.
1. Hold a flat-blade screwdriver at an angle and insert it into the
release hole.
2. With the flat-blade screwdriver still inserted into the release hole,
remove the wire from the terminal insertion hole.
3. Remove the flat-blade screwdriver from the release hole.
4. Recommended Ferrules and Crimp Tools
Recommended Ferrules
XW5T-P1.5-@-@@
XW5T-P2.5-@-@@
XW5T-P4.0-@-@@
Note: 1. Make sure that the outer diameter of the wire is smaller than
the inner diameter of the insulation sleeve of the
recommended ferrule.
2. Make sure that the ferrule processing dimensions conform
to the following figure.
10 to 15°
1
3
2
Flat-blade screwdriver
Wire
Applicable
wire
Ferrule
Conductor
length
(mm)
Recommended ferrules
(mm
2
)
(AWG)
Manufactured
by Phoenix
Contact
Manufactured
by Weidmuller
Manufactured
by Wago
0.14 26 8 AI 0.14-8 H0.14/12 ---
0.25 24 8 AI 0.25-8 H0.25/12
FE-0.25-8N-YE
0.34 22 8 AI 0.34-8 H0.34/12
FE-0.34-8N-TQ
0.50 20 8 AI 0.5-8 H0.5/14
FE-0.5-8N-WH
0.75 18 8 AI 0.75-8 H0.75/14
FE-0.75-8N-GY
1.00 18 8 AI 1-8 H1.0/14 FE-1.0-8N-RD
Recommended crimp tool
CRIMPFOX6
CRIMPFOX6-F
CRIMPFOX10S
PZ6 roto Variocrimp4
Applicable
wire
Ferrule
Conductor
length
(mm)
Recommended ferrules
(mm
2
)
(AWG)
Manufactured
by Phoenix
Contact
Manufactured
by Weidmuller
Manufactured
by Wago
0.25 24 10 AI 0.25-10 YE --- ---
0.34 22 10 AI 0.34-10 TQ --- ---
0.50 20 10 AI 0.5-10 WH H0.5/16
FE-0.5-10N-WH
0.75 18 10 AI 0.75-10 GY H0.75/16
FE-0.75-10N-GY
1.00 18 10 AI 1-10 RD H1.0/16
FE-1.0-10N-RD
1.50 16 10 AI 1.5-10 BK H1.5/16
FE-1.5-10N-BK
2.50 14 10 AI 2.5-10 BU H2.5/16DS
FE-2.5-10N-BU
Recommended crimp tool
CRIMPFOX6
CRIMPFOX6-F
CRIMPFOX10S
PZ6 roto Variocrimp4
Applicable
wire
Ferrule
Conductor
length
(mm)
Recommended ferrules
(mm
2
)
(AWG)
Manufactured
by Phoenix
Contact
Manufactured
by Weidmuller
Manufactured
by Wago
0.25 24 12 AI 0.25-12 BU --- ---
0.34 22 12 AI 0.34-12 TQ --- ---
0.50 20 12 AI 0.5-12 WH ---
FE-0.5-12N-WH
0.75 18 12 AI 0.75-12 GY H0.75/18
FE-0.75-12N-GY
1.00 18 12 AI 1-12 RD H1.0/18
FE-1.0-12N-RD
1.50 16 12 AI 1.5-12 BK H1.5/18D
FE-1.5-12N-BK
2.50 14 12 AI 2.5-12 BU H2.5/19D
FE-2.5-12N-BU
4.00 12 12 AI 4-12 GY H4.0/20D
FE-4.0-12N-GY
Recommended crimp tool
CRIMPFOX6
CRIMPFOX6-F
CRIMPFOX10S
PZ6 roto Variocrimp4
8 mm
2.1 mm max.
2.7 mm max.