Datasheet

Sysmac Studio
20
Note: For details, refer to "Unit Configuration" of "Machine Automation Controller NJ-Series" of System Design Guide on the Sysmac Catalogue
(Cat. No. P072).
*1. To use the SECS/GEM service of the SECS/GEM CPU Unit, the SECS/GEM Configurator (WS02-CGTL1) is additionally required.
*2. A communications unit for connecting to EtherCAT network (3G3AX-MX2-ECT with unit version 1.1 or higher) is additionally required.
*3. A communications unit for connecting to EtherCAT network (3G3AX-RX-ECT) is additionally required.
*4. A communications unit for connecting to EtherCAT network (E3NW-ECT) is additionally required.
*5. The E3NX-CA0 can be used with the Sysmac Studio version 1.16 or higher.
*6. A communications unit for connecting to EtherCAT network (E3X-ECT) is additionally required.
*7. The EtherCAT Coupler Unit (NX-ECC20@ with unit version 1.0 or later) or EtherNet/IP Coupler Unit (NX-EIC202 with unit version 1.0 or later)
is additionally required. For details, refer to the NX-series "Version Information".
*8. The serial communications instructions for the CIF Units are supported by the CPU Units with unit version 1.11 or later and the Sysmac Studio
version 1.15 or higher. If the serial communications instructions are not used, CIF Units can be used with the combination of CPU Units with
unit version 1.10 or later and the Sysmac Studio version 1.12 or higher. Refer to the NJ/NX-series Instructions Reference Manual (Cat. No.
W502-E1-15 or later) for the serial communications instructions for the CIF Units.
*9. The EtherCAT Coupler Unit (NX-ECC20@ with unit version 1.1 or later) or EtherNet/IP Coupler Unit (NX-EIC202 with unit version 1.0 or later.
The NX-3500 cannot be connected.) is additionally required. For details, refer to the "Version Information" of NX-series Safety Control Units.
*10.The NX-SL3500 with unit version 1.0 or later can be used with the Sysmac Studio version 1.08 or higher, and unit version 1.1 or later can be
used with the Sysmac Studio version 1.10 or higher.
*11.The Safety Control Units with unit version 1.1 can be used with the Sysmac Studio version 1.10 or higher.
HMIs
NS-series
To connect to NJ501-@@@@:
NS system version 8.5 or later
CX-Designer version 3.3 or higher
To connect to NJ301-@@@@/NJ101-@@@@:
NS system version 8.61 or later
CX-Designer version 3.4 or higher
To connect to NX701-@@@@:
NS system version 8.9 or later
CX-Designer version 3.64 or higher
To connect to NX1P2-@@@@:
NS system version 8.93 or later
CX-Designer version 3.64 or higher
NS5-MQ11(B)-V2/-SQ11(B)-V2/-TQ11(B)-V2
NS8-TV01(B)-V2
NS10-TV01(B)-V2
NS12-TS01(B)-V2
NS15-TX01S-V2/-TX01B-V2
All versions
NA-series
To connect to NX701-@@@@/NJ101-@@@@:
NA system version 1.02 or later
Sysmac Studio version 1.13 or higher
To connect to NY512-@@@@/NY532-@@@@:
NA system version 1.06 or later
Sysmac Studio version 1.17 or higher
To connect to NX1P2-@@@@:
NA system version 1.07 or later
Sysmac Studio version 1.17 or higher
NA5-15W@@@@
NA5-12W@@@@
NA5-9W@@@@
NA5-7W@@@@
Ver.1.11 or higher
Series Unit version Model Applicable versions