Datasheet
S8V-NF
35
Checking Connections
• After the insertion, pull gently on the wire to make sure that it will not
come off and the wire is securely fastened to the terminal block
• If you use a ferrule with a conductor length of 10 mm, part of the
conductor may be visible after the ferrule is inserted into the
terminal block, but the product insulation distance will still be
satisfied.
Removing Wires from the Push-In Plus Terminal Block
Use the following procedure to remove wires from the terminal block.
The same method is used to remove stranded wires, solid wires, and
ferrules.
1.
Hold a flat-blade screwdriver at an angle and insert it into the release
hole.
2. With the flat-blade screwdriver still inserted into the release hole,
remove the wire from the terminal insertion hole.
3. Remove the flat-blade screwdriver from the release hole.
Recommended Ferrules and Crimping Tools
Recommended Ferrules
Note: 1. Make sure that the outer diameter of the wire is smaller than
the inner diameter of the insulating sleeve of the
recommended ferrule.
2. Make sure that the ferrule processing dimensions conform
to the following figure.
Recommended Flat-blade Screwdriver
Use a flat-blade screwdriver to connect and remove wires. Use the
following flat-blade screwdriver.
The following table shows manufacturers and models as of 2015/Dec.
* OMRON’s exclusive purchase model XW4Z-00B is available to
order as SZF 0-0,4×2,5 (manufactured by Phoenix Contact).
Flat-blade screwdriver
10 to 15°
1
3
2
Applicable
wire
Ferrule
Conductor
length
(mm)
Stripping
length (mm)
(Ferrules
used)
Recommended ferrules
(mm
2
)
(AWG)
Manufactured
by Phoenix
Contact
Manufactured
by Weidmuller
Manufactured
by Wago
0.50 20
8 10 AI 0,5-8 H0.5/14
FE-0.5-8N-WH
10 12 AI 0,5-10 H0.5/16
FE-0.5-10N-WH
0.75 18
8 10 AI 0,75-8
H0.75/14
FE-0.75-8N-GY
10 12 AI 0,75-10
H0.75/16
FE-0.75-10N-GY
1/1.25 18/17
8 10 AI 1-8 H1.0/14
FE-1.0-8N-RD
10 12 AI 1-10 H1.0/16
FE-1.0-10N-RD
1.25/1.5
17/16
8 10 AI 1,5-8 H1.5/14
FE-1.5-8N-BK
10 12 AI 1,5-10 H1.5/16
FE-1.5-10N-BK
2.5
14 10 12 AI 2,5-10
H2.5/16DS
FE-2.5-10N-BU
Recommended crimp tool
CRIMPFOX6
CRIMPFOX6T-F
CRIMPFOX10S
PZ6 roto Variocrimp4
Model number Manufacturer
ESD 0,40×2,5 Wera
SZS 0,4×2,5
SZF 0-0,4×2,5 *
Phoenix Contact
0.4×2.5×75 302 Wiha
AEF.2,5×75 Facom
210-719 Wago
SDI 0.4×2.5×75 Weidmuller
8 to 10mm
2.6 mm max.
2.8 mm max.
Side
0.4 mm
2.5 mm dia.
2.5 mm
Front