Datasheet

G2RV-SR/G3RV-SR
22
G2RV-SR G3RV-SR
Common AccessoriesCommon Precautions
2. Removing Wires from the Terminal
Use the following procedure to remove wires from the terminal.
The same method is used to remove stranded wires and ferrules.
(1) Hold a flat-blade screwdriver at an angle and insert it into the
release hole.
(2) With the flat-blade screwdriver still inserted into the release hole,
remove the wire from the terminal insertion hole.
(3) Remove the flat-blade screwdriver from the release hole.
3. Recommended ferrules and tools
Recommended ferrules
*1. Make sure that the outer diameter of the wire is smaller than the
inner diameter of the insulating sleeve of the recommended
ferrule.
*2. Make sure that the ferrule processing dimensions conform to the
following figure.
Recommended Flat-blade Screwdriver
Use a flat-blade screwdriver to connect and remove wires.
Use the following flat-blade screwdriver.
The following table is the manufacturer and format at the time in
December 2015.
Screw Terminal
• Screw terminal
• Tightening Torque
0.4 N • m
• Electric wiring
Use the electric wire of specified size as shown above. The length
of the that is not covered is 8 mm.
<G2RV>
Operating latching lever (test switch)
When operating the latching lever for G2RV-SR701/501
series, use a 2.5 mm width flat-blade screwdriver.
• Applicable flat-blade screwdriver
Flat-blade screwdriver with parallel cutting edge: shaft diameter
2.5
mm (3.0 mm max.)
• Always turn OFF the power supply before operating latching lever.
• Return to its original state after using the latching lever.
• Do not use the latching lever as a switch.
• Operation durability of the latching lever is 100 times or more.
• Do not keep the latching lever ON for a long period of time (24
hours or more) in order to maintain the operation check function.
Applicable
wire
Ferrules
Conduct
length
(mm)
Recommended ferrules
(mm
2
) (AWG)
Phoenix
Contact
product
Weidmuller
product
Wago product
0.5 20 8 AI0.5-8 H0.5/14 FE-0.5-8N-WH
0.75 18 8 AI0.75-8 H0.75/14 FE-0.75-8N-GY
1 18 8 AI1-8 H1.0/14 FE-1.0-8N-RD
1.5 16 8 AI1.5-8 H1.5/14 FE-1.5-8N-BK
Recommended crimp
tool
CRIMPFOX6
CRIMPFOX6T-F
CRIMPFOX10S
PZ6 roto Variocrimp4
Model Manufacturer
XW4Z-00B Omron
ESD 0.40✕2.5 Wera
SZF 0.4✕2.5 Phoenix Contact
0.4✕2.5✕75 302 Wiha
AEF.2.5✕75 Facom
210-719 Wago
*1
*1.
Insulated types of Flat-blade Screw driver, strongly recommended
to prevent from an electric shock.
SDI 0.4✕2.5✕75 Weidmuller
*1
98 20 25 KNIPEX
*1
(2)
10 to 15°
Wire
Flat-blade screwdriver
(1)
(3)
(2)
(1)
(3)
8 mm
2.1 mm max.
8 mm
Side
0.4 mm
2.5 mm dia.
2.5 mm
Front
Wired type
Applicable wire
size
Stripping
length
Stranded wires, without
ferrule
0.5 to 1.5 mm
2
8 mm
Stranded wires, with ferrule
and plastic collar
0.5 to 1.5 mm
2
8 mm
Stranded wires with ferrule,
without plastic collar
0.5 to 1.5 mm
2
8 mm
Single wire 0.5 to 1.5 mm
2
8 mm
Stripping length
8 mm
Screw terminal
Shaft diameter 2.5 mm (3.0 mm max.)
Driver with a thick shaft cannot be used.
Wide flat-blade screwdriver
Parallel cutting edge flat-blade screwdriver