Datasheet

ManualsBrandsOmron Industrial Automation ManualsAutomationLimit Switch, Adjustable Roller Lever, 1NO/1NC,

General-purpose Limit Switch HL-5000

Economical, Miniature Limit Switch

Boasting Rigid Construction

Highly rigid construction (head and cover snugly fit

in box).

Dustproof and drip-proof construction.

Smooth operation with greater OT.

Easy-to-wire conduit opening design.

Models with grounding terminals conform to the CE

marking.

Ordering Information

Model Number Legend

HL-5jjj

123

1. Actuators

000: Roller lever

030: Adjustable roller lever

050: Adjustable rod lever

100: Sealed plunger

200: Sealed roller plunger

300: Coil spring

500: Remote control wire

2. Ground Terminal Specifications

Blank: Without ground terminal

G: With ground terminal/M5 tapping on the rear side

3. Contact

Blank: Standard (silver rivet contact)

A: Gold plating

List of Models

Actuator Roller lever Adjustable

roller lever

Adjustable

rod lever

Sealed

plunger

Sealed roller

plunger

Coil spring

Model HL-5000 HL-5030 HL-5050 HL-5100 HL-5200 HL-5300

Note: HL-5000 Limit Switches are offered with a choice of ground terminal/M5 tapping on the rear side conforming to various standards.

When placing an order, add the code to the model number to indicate if ground terminal/M5 tapping on the rear side is required.

-G: with ground terminal/M5 tapping on the rear side

Summary of content (7 pages)

PAGE 1
General-purpose Limit Switch HL-5000 Economical, Miniature Limit Switch Boasting Rigid Construction Highly rigid construction (head and cover snugly fit in box). Dustproof and drip-proof construction. Smooth operation with greater OT. Easy-to-wire conduit opening design. Models with grounding terminals conform to the CE marking. Ordering Information Model Number Legend HL-5jjj 1 2 3 2. Ground Terminal Specifications Blank: Without ground terminal G: With ground terminal/M5 tapping on the rear side 3.
PAGE 2
HL-5000 HL-5000 Specifications Ratings Rated voltage Non-inductive load Resistive load NC Inductive load Lamp load NO NC Inductive load NO NC Motor load NO NC NO 125 VAC 5A 1.5 A 0.7 A 3A 2A 1A 250 VAC 5A 1A 0.5 A 3A 1.5 A 0.8 A 12 VDC 5A 3A 4A 3A 24 VDC 5A 3A 4A 3A Inrush current Note: NC 24 A max. NO 12 A max. 1. The above figures are for standard currents. 2. Inductive loads have a power factor of 0.4 min. (AC) and a time constant of 7 ms max. (DC). 3.
PAGE 3
HL-5000 HL-5000 Operating Characteristics Model HL-5000 HL-5030 (see note) HL-5050 (see note) HL-5100 HL-5200 HL-5300 HL-5500 OF max. 7.35 N 7.35 N 7.35 N 8.83 N 8.83 N 1.47 N 19.61 N RF min. 0.98 N 0.98 N 0.98 N 1.47 N 1.47 N --- 1.96 N PT max. 20° 20° 20° 1.5 mm 1.5 mm 30 mm 1.5 mm OT min. 50° 50° 50° 4 mm 4 mm --- 4.5 mm MD max. 12° 12° 12° 1 mm 1 mm --- 0.7 mm OP --- 30±0.8 mm 40±0.8 mm --- --- Note: 1. Measured with the types of the 31.
PAGE 4
HL-5000 HL-5000 Dimensions Note: 1. All units are in millimeters unless otherwise indicated. 2. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. Roller Lever HL-5000 17.5 dia. × 6.6 (See note 1) (See note 2) Three, M5 x 12 M3 cover Allen-head clamping bolt screws Two, 5.2+0.2 0 dia. mounting holes Note: 1. The resin roller can be mounted anywhere in 360°. 2. The head can be mounted in any of the four directions. Rubber connector Adjustable Roller Lever HL-5030 17.
PAGE 5
HL-5000 HL-5000 Sealed Roller Plunger HL-5200 PT OP 50±0.2 12.7 dia. × 4.8 stainless steel roller 16.5 Two, M3 head clamping screws (See note) 20.2 Three, M3 head 60.6 Note: (19) 4.1 Coil Spring HL-5300 Resin rod PT (See note 1) 6.6 dia. 3.2 dia. 30 (see note 2) 110±2.5 The head can be mounted in either of the two directions. Dimensions not shown are the same as HL-5000. 38±0.2 Two, M3 head clamping screws 16.5 42±0.2 20.2 Note: 60.6 50±0.2 4.1 (19) 1.
PAGE 6
HL-5000 HL-5000 The head of the HL-5200 can be mounted in two directions only. Refer to the following illustration. HL-5200 Head mounting screw (white) Head-mounting screw (white) Precautions 5. Tighten the three mounting screws evenly. The optimum tightening torque for each screw is 0.49 to 0.59 N S m {5 to 6 kgf S cm}. Wiring Wiring Procedure 1. Loosen the cover mounting screws and remove the cover. 2. Disconnect the rubber connector from the box conduit and press-fit a solderless terminal.
PAGE 7
HL-5000 HL-5000 Others • Do not use the Limit Switch outdoors, otherwise the Limit Switch will become damaged by rust or ozone. • • The Limit Switch is not suitable in places exposed to the spray of rainwater, seawater, or oily water. Consult your OMRON representative for models resisting rainwater, seawater, and oily water. If high-sealing performance is required along with shielded wiring or conduit wiring, use the D4C or WL. Correct Tightening Torque A loose screw may result in a malfunction.