Datasheet

G2RV-SR/G3RV-SR
21
G2RV-SR G3RV-SR
Common AccessoriesCommon Precautions
Mounting
• Before you start wiring, please make sure that the socket is
securely attached to the mounting rail. If the socket is unstable, it
may come loose and risk of injury towards the workers.
•
Please insert the flat-blade screwdriver to the bottom of the hole. If
you do not insert the flat-blade screwdriver correctly, the cable will
not be connected correctly
.
• When lubricant such as oil is attached to the tip of the driver, the
driver will fall off, with a risk of injury towards the workers.
Usage
• Please select the load within the rated range. Doing so may result
in damage, malfunction, or failure.
• Please use the power of the rated frequency. It may cause
malfunction, failure, or risk of burnout.
<G3RV>
• Install G3RV according to instructions Mounting on page 23. If you
install in the wrong direction, abnormal heat is generated, and may
lead to short-circuiting or burning the output element.
• G3RV is an SSR that generates heat. Please observe the ambient
temperature setting range of G3RV. If installing in an enclosed
space, set a fan, and ventilate.
• When mounting G3RV to DIN rail, firmly fits into the groove. If it is
not properly installed, there is a risk of it falling.
Wiring
• For the current to be applied, make sure a wire size with margin is used.
Otherwise, excessive heat generated by the wires may cause burning
.
• Do not attempt to use the wire if the coat is torn. Not doing so may
result in electric shock.
• Always turn OFF the power supply before performing wiring. Not
doing so may cause electrical shock.
<G3RV>
• The wires of the socket for G3RV socket should not be passed
through the same duct as that being connected to the high-voltage
power supply. Otherwise, inductive noise may damage the G3RV
or cause it to malfunction.
Push-In Plus Terminal Block
• Do not wire anything to the release holes.
•
Do not tilt or twist a flat-blade screwdriver while it is inserted into a release
hole on the terminal block. The terminal block may be damaged
.
• Insert a flat-blade screwdriver into the release holes at an angle.
The terminal block may be damaged if you insert the screwdriver
straight in.
• Do not allow the flat-blade screwdriver to fall out while it is inserted
into a release hole.
• Do not bend the wire past its natural bending radius or pull on it
with excessive force. Doing so may cause the wire disconnection.
•
Do not insert more than one wire into each terminal (insertion) hole .
• To prevent wiring materials from smoking or ignition, confirm wire
ratings and use the wiring materials given in the following table.
Disposal
• When disposing of the product, do not put into the fire.
• Do not use or store the product in the following locations. Doing so
may result in damage, malfunction, or deterioration of performance
characteristics.
• Where vibration or shock is directly transmitted to the body
• Do not use the product where the socket could touch a solvent
or alkaline agent.
• Do not insert short bar in the hole for wire or screw driver, it may
cause the result of failure of pull out.
If insert short bar in the hole for wire or screw driver and try to pull
out, it may cause damage for short bar or socket.
• Please insert P2RVC terminal into the short bar insertion hole of
G2RV-SR/G3RV-SR. If insert P2RVC into the release hole or
terminal (insertion) hole wrongly, P2RVC may stuck and can not
remove and it may cause result of damage on P2RVC and G2RV-
SR/G3RV-SR.
Push-In Plus Terminal Block
1. Connecting Wires to the Push-In Plus Terminal Block
Part Names of the Terminal Block
Connecting Wires with Ferrules and Solid Wires
Insert the solid wire or ferrule straight into the terminal block until the
end strikes the terminal block.
• If a wire is difficult to connect because it is too thin, use a flat-blade
screwdriver in the same way as when connecting stranded wire.
Connecting Stranded Wires
Use the following procedure to connect the wires to the terminal block.
(1) Hold a flat-blade screwdriver at an angle and insert it into the
release hole.
The angle should be between 10°and15°. If the flat-blade
screwdriver is inserted correctly, you will feel the spring in the
release hole respond.
(2) With the flat-blade screwdriver still inserted into the release hole,
insert the wire into the terminal hole until it strikes the terminal
block.
(3) Remove the flat-blade screwdriver from the release hole.
Recommended Wire
Stripping length
(Ferrules not used)
0.5 to 1.5 mm
2
/AWG20 to AWG16 8 mm
Precautions for Correct Use
Release hole
Terminal (Insertion) hole
Release hole
Terminal
(Insertion) hole
Ferrules or
solid wire
(2)
Flat-blade screwdriver
Stranded Wires
10 to 15°
(1)
(3)
(2)
(1)
(3)