Datasheet

G-65E3FS
E3FS
Rating and Performance
Sensors
E3FS-10B4 series
Sensing method Through-beam
Controller F3SP-U3P-TGR, F3SP-U5P-TGR
Supply voltage 24 VDC ± 10% (ripple p-p 10% max.)
Effective aperture angle (EAA) ±5° (at 3 m)
Current consumption
Emitter:50 mA max.
Receiver:25 mA max.
Sensing distance 10 m
Standard sensing object Opaque object: 11 mm min. in diameter
Response time 2.0 ms (E3FS only) Response time of controller = Response time of the system
Control output
PNP transistor output, load current: 100 mA max., residual voltage: 2 V max. (Except for volta-
ge drop due to cable extension)
Test input (Emitter)
21.5 to 24 VDC: Emitter OFF (source current: 3 mA max.)
Open or 0 to 2.5 V: Emitter ON (leakage current: 0.1 mA max.)
Power supply reset time 100 ms
Ambient light intensity
Incandescent lamp: 3.000 lx max. (light intensity on the receiver surface)
Sunlight: 10,000 lx max. (light intensity on the receiver surface)
Ambient temperature Operating: -10 to 55°C, storage: -30 to 70°C (with no icing or condensation)
Ambient humidity Operating: 35% to 85%, storage: 35% to 95% (with no icing or condensation)
Insulation resistance 20 MΩ min. (at 500 VDC)
Dielectric strength 1,000 VAC 50/60 Hz 1 min
Vibration resistance
Malfunction 10 to 55 Hz, double amplitude: 1.5 mm, 2 h each in the X, Y, and Z directions
Operating limit 10 to 55 Hz, double amplitude: 0.7 mm, 50 min each in the X, Y, and Z directions
Shock resistance
Malfunction 500 m/s² (approx. 50 G), 3 times each in the X, Y, and Z directions
Operating limit 100 m/s² (approx. 10 G), 1,000 times in the X, Y, and Z directions
Degree of protection IP67 (IEC standard)
Light source Infrared LED
Operation indicators
Emitter: Emitting (orange)
Receiver: Output ON (green), Output OFF (red)
Protection Output short-circuit protection, reverse polarity protection
Weight (in packaging)
E3FS-10B4 2M (ABS resin case): approx. 150 g for 1 set (weight without cable: approx. 55 g)
E3FS-10B4-M1-M (metal case): approx. 125 g for 1 set
Applicable standard
IEC61496-1, EN61496-1 Type 2 ESPE (Electro-Sensitive Protective Equipment)
IEC61496-2, prEN61496-2 Type 2 AOPD (Active Opto-electronic Protective Devices)
Accessories Emitter, Receiver, four nuts for mounting, and an instruction manual
Parallel Operating Range Mutual interference Range Excess Gain Ratio
600
400
200
0
−200
−400
−600
128104620
Distance X (m)
Operating position Y (mm)
Y
X
Emitter
Receiver
800
600
400
200
0
−200
−400
−600
−800
128104620
Distance X (m)
Mutual interference range Y (mm)
Y
X
Emitter
Receiver
10
9
8
7
6
5
4
3
2
1
0
3020 2510 1550
Distance (m)
Reception Light output margin
F502-EN2-04.book Seite 65 Dienstag, 26. Juli 2005 5:48 17