Datasheet

ManualsBrandsOmron Industrial Automation ManualsAutomationRFID Non-Contact Safety Switch, 2NC + 1NO, IP67, Connector, M12, 8-Pin/Cable, 250 mm

RFID Non-contact Safety Switches

F3S-TGR-N_M / F3S-TGR-N_U

RFID Non-contact switches are designed to monitor hinge, sliding or

removal guard doors.

• Based on RFID technology (code) and hall technology

(distance check)

• The RFID-design covers two operation models with very high

anti-tamper level:

• M-types (Master coded): Any sensor works with any actuator

(re-teach needed if exchange of actuator)

• U-types (Unique coded): Each sensor and actuator use a unique

code. This is a solution for applications that requires even a higher

anti-tamper level

• Connect up to 20 switches in series

• LED supports easy diagnosis

• Compensation of mechanical tolerances

• Non-contact – no abrasion – no particles

• Operates with all OMRON safety controllers

• Suitable for CIP/SIP processes and high pressure cleaning due

IP69K (pre-wired types)

• Conforms to safety categories up to PLe acc. EN ISO 13849-1

Model number structure

1. Type:

L: Elongated Sensor

S: Small Sensor

2. Code:

M: Master Code

U: Unique Codes

3. Cable length/connection

05: 5 m Cable

10: 10 m Cable

M1J8: M12 male connector, 8 pin, fitted with 250 mm cable

Ordering information

Master coded: Any actuator will operate with any sensor (Teach process needed, if actuator will be changed: Power down - place actuator to

sensor - power up).

Unique coded: Only one actuator fits to the code of the sensor (Replacement of only sensor OR actuator is not possible)

Elongated sensors

Small sensors

F3S-TGR-N@P@-21-@

12 3

Type Cable connection

Contact

configuration

Order code

Master coded

Re-teach needed if exchange of actuator: Power down - replace the actuator and close the door or bring the new actuator close to the sensor - power up.

Unique coded

5 m pre-wired

2NC/1NO

F3S-TGR-NLPM-21-05 F3S-TGR-NLPU-21-05

10 m pre-wired F3S-TGR-NLPM-21-10 F3S-TGR-NLPU-21-10

M12, 8 pin, fitted with 250 mm cable F3S-TGR-NLPM-21-M1J8 F3S-TGR-NLPU-21-M1J8

Type Cable connection

Contact

configuration

Order code

Master coded

Re-teach needed if exchange of actuator: Power down - replace the actuator and close the door or bring the new actuator close to the sensor - power up.

Unique coded

5 m pre-wired

2NC/1NO

F3S-TGR-NSPM-21-05 F3S-TGR-NSPU-21-05

10 m pre-wired F3S-TGR-NSPM-21-10 F3S-TGR-NSPU-21-10

M12, 8 pin, fitted with 250 mm cable F3S-TGR-NSPM-21-M1J8 F3S-TGR-NSPU-21-M1J8

Summary of content (10 pages)

PAGE 1
RFID Non-contact Safety Switches F3S-TGR-N_M / F3S-TGR-N_U RFID Non-contact switches are designed to monitor hinge, sliding or removal guard doors. • Based on RFID technology (code) and hall technology (distance check) • The RFID-design covers two operation models with very high anti-tamper level: • M-types (Master coded): Any sensor works with any actuator (re-teach needed if exchange of actuator) • U-types (Unique coded): Each sensor and actuator use a unique code.
PAGE 2
F3S-TGR-N_M / F3S-TGR-N_U Accessories Cables 8-pin T-Connector connection cable Actuators (only for master coded types) Mounting screws 2m 5m 10 m 25 m T-Connector for M12 connector 0.6 m, M12-8pin 2 m, M12-8pin 5 m, M12-8pin 10 m, M12-8pin for F3S-TGR-NLPM for F3S-TGR-NSPM Set of Torx safety screws (M4, 4 × 30 mm, 4 × 20 mm, 4 × 10 mm; incl.
PAGE 3
F3S-TGR-N_M / F3S-TGR-N_U Specifications Electrical Data F3S-TGR-N_PM F3S-TGR-N_PU Technology RFID (Code) and hall sensing (Distance check) Serial switching up to 20 pcs. in series Code Master coded: Every switch same code*1 Indicator LED lighted - Indication of safety circuit closed - Door close LED dark - Indication of safety circuit opened - Door open Power supply 24 VDC ±10% Power consumption Max.
PAGE 4
F3S-TGR-N_M / F3S-TGR-N_U Dimensions Elongated sensor (Sensor/Actuator) F3S-TGR-NLPM F3S-TGR-NLPU 88 88 78 78 18.50 25 3.50 25 7 4.50 13 13 3 3 Ø 5.20 Small sensor (Sensor/Actuator) F3S-TGR-NSPM F3S-TGR-NSPU 13 50 13 22 4.50 4.50 3 20.5 4.20 25.50 20.5 25.50 4.20 3 50 22 Circuit Schematic The RFID non-contact switches are working with both principles, based on RFID and hall technology.
PAGE 5
F3S-TGR-N_M / F3S-TGR-N_U Wiring examples G9SB Single Sensor Application with G9SB-2002-C (up to Safety PLe acc. EN ISO 13849-1) +24 V GND Start A1 F3S-TGR-N_M or F3S-TGR-N_U Actuator Sensor red blue black white yellow green brown orange A2 T31 KM1 G9SB-2002-C T11 T12 T21 T22 Feedbackloop KM2 T32 Auxiliary (NO) KM1 13 14 23 24 KM2 KM2 KM1 M +Us GND Series connection Application, up to 20 Sensors with G9SB-2002-C (up to Safety PLd acc.
PAGE 6
F3S-TGR-N_M / F3S-TGR-N_U G9SA Single Sensor Application with G9SA-301 (up to Safety PLe acc. EN ISO 13849-1) +24 V GND Start A1 F3S-TGR-N_M or F3S-TGR-N_U Actuator Sensor red blue black white yellow green brown orange A2 T31 KM1 Feedbackloop G9SA-301 KM2 T32 T11 T12 T21 T22 Auxiliary (NO) KM1 14 13 23 24 KM2 KM2 KM1 M +Us GND Series connection Application, up to 20 Sensors with G9SA-301 (up to Safety PLd acc.
PAGE 7
F3S-TGR-N_M / F3S-TGR-N_U G9SP Single Sensor Application with G9SP (up to Safety PLe acc. EN ISO 13849-1) +24 V GND V0 G0 F3S-TGR-N_M or F3S-TGR-N_U Sensor Actuator red blue black white yellow green brown orange G9SP Test 0 In 0 Test 1 In 1 Auxiliary (NO) Series connection Application, up to 20 Sensors with G9SP (up to Safety PLd acc.
PAGE 8
F3S-TGR-N_M / F3S-TGR-N_U T-Connector and Connection Cable Series connection with up to 20 pcs. for example with G9SA-301 (up to Safety PLd acc. EN ISO 13849-1) F3S-TGR-N_M or F3S-TGR-N_U Actuator +24 V GND brown Sensor Start green A1 A2 T31 KM1 Y92E-M12FSM12MSPURSH8_M-L Length: 0.6 m, 2 m, 5 m or 10 m F39-TGR-NT Feedbackloop G9SA-301 blue white yellow pink T11 T12 T22 T21 KM2 T32 KM1 13 Y92E-M12FSM12MSPURSH8_M-L Length: 0.
PAGE 9
F3S-TGR-N_M / F3S-TGR-N_U Safety Precautions !WARNING Be sure to turn OFF the power before performing wiring. Do not touch charge parts (e.g., terminals) while power is ON. Doing so may result in electric shock. Do not allow the actuator to come close to the switch with the door open. Doing so may cause machinery to start operating and may result in injury. Keep actuators (magnets) away from magnetically sensitive equipment like PC harddisks, floppy disks etc.
PAGE 10
F3S-TGR-N_M / F3S-TGR-N_U ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. Cat. No. F14E-EN-02A 10 In the interest of product improvement, specifications are subject to change without notice.