User Manual

ManualsBrandsOmron Industrial Automation ManualsAutomationThermostat 100...240 VAC

NO. MODE DISPLAY FUNCTION RANGE UNIT DEFAULT USER REMARKS

1 pmov MOVE TO PROTECT LEVEL -1999 to 9999 - 0 *3 Only available when password <> zero (0)

oapt OPERATION / ADJUSTMENT PROTECTION 0 to 3 - 0 *3 Protect level of parameter (0=Low 3=High)

3 PROTECT

icpt INITIAL SETTING / COMMUNICATION PROTECT 0 to 2 - 1 *3 Protect level of levels (0=Low 2=High)

4 LEVEL

wtpt SETTING CHANGE PROTECTION off / on - off *3

pmsk PARAMETER MASK off / on - on *3 Displayed only when setting parameter mask, off shows all parameter

6 prlp MOVE TO PROTECT LEVEL PASSWORD -1999 to 9999 - 0

*3 press "level" key with up/down key to change password

a-m AUTO/MANUAL SELECT - - --Pid control only, displayed when "Additional Auto/Manual select" is on

m-sp MULTI SETPOINT (SETPOINT 0-3) 0 to 3 - 0 Gives the number of the current active setvalue (0-3)

sp-m SETPOINT DURING SP RAMP READ ONLY E.U. --Current setvalue while sv is ramping up to target sv

ct1 ct2 HEATER CURRENT 1 AND 2 VALUE MONITOR READ ONLY A --Reads the heater current trough CT in conduction (MV <> 0%)

lcr1 lcr2 LEAKAGE CURRENT 1 AND 2 VALUE MONITOR READ ONLY A --Reads the heater current trough CT when MV = 0%

12 prst PROGRAM START

rset / strt

- rset

Programmer idle (rset) or running (strt )

sktr SOAK TIME REMAINING 0 - 9999 m/h --Reads the remaining soak time before program end

14 OPERATION r-s RUN / STOP MODE

run / stop

- run

stop

= No control, only PV measurement and alarms

15 LEVEL

al-1 ALARM VALUE 1 -1999 to 9999 E.U. 0 *3 Set Alarm value X for alt1 =2, 3, 6, 7, 8, 9, 10 and 11

al1h ALARM VALUE 1 UPPER LIMIT -1999 to 9999 E.U. 0 *3 Set Alarm value H for alt1 =1, 4 and 5

al1l ALARM VALUE 1 LOWER LIMIT -1999 to 9999 E.U. 0 *3 Set Alarm value L for alt1 =1, 4 and 5

al-2 ALARM VALUE 2 -1999 to 9999 E.U. 0 *3 Set Alarm value X for alt2 =2, 3, 6, 7, 8, 9, 10 and 11

al2h ALARM VALUE 2 UPPER LIMIT -1999 to 9999 E.U. 0 *3 Set Alarm value H for alt2 =1, 4 and 5

al2l ALARM VALUE 2 LOWER LIMIT -1999 to 9999 E.U. 0 *3 Set Alarm value L for alt2 =1, 4 and 5

al-3 ALARM VALUE 3 -1999 to 9999 E.U. 0 *3 Set Alarm value X for alt3 =2, 3, 6, 7, 8, 9, 10 and 11

al3h ALARM VALUE 3 UPPER LIMIT -1999 to 9999 E.U. 0 *3 Set Alarm value H for alt3 =1, 4 and 5

al3l ALARM VALUE 3 LOWER LIMIT -1999 to 9999 E.U. 0 *3 Set Alarm value L for alt3 =1, 4 and 5

o MV MONITOR (OUT1) READ ONLY % - - Read PID heat output value

c-o MV MONITOR (OUT2) READ ONLY % --Read PID cool output value

l.adj ADJUSTMENT LEVEL READ ONLY - --Displayed one time when moving to adjustment level

at AUTO TUNE EXECUTE/CANCEL off / on - off Performs a one shot autotune

cmwt COMMUNICATION WRITING ALLOWED off / on - off Parameter writing through serial comms allowed

ct1 ct2 HEATER CURRENT 1 AND 2 VALUE MONITOR READ ONLY A - - Reads the heater current trough CT in conduction (MV <> 0%)

lcr1 lcr2 LEAKAGE CURRENT 1 AND 2 VALUE MONITOR READ ONLY A - - Reads the heater current trough CT when MV = 0%

hb1 HEATER BURNOUT DETECTION 1 0,0 to 50,0 A 0.0 Set low current detection level (0 = OFF)

hb2 HEATER BURNOUT DETECTION 2 0,0 to 50,0 A 0.0 Set low current detection level (0 = OFF)

hs1 HEATER SHORT SSR DETECTION 1 0,0 to 50,0 A 50.0 Set high leakage current detection level (50 = OFF)

hs2 HEATER SHORT SSR DETECTION 2 0,0 to 50,0 A 50.0 Set high leakage current detection level (50 = OFF)

sp-0 SET POINT 0 SETPOINT UPPER to LOWER E.U. 0

36 sp-1 SET POINT 1 SETPOINT UPPER to LOWER E.U. 0

37 sp-2 SET POINT 2 SETPOINT UPPER to LOWER E.U. 0

38 sp-3 SET POINT 3 SETPOINT UPPER to LOWER E.U. 0

39 ins TEMPERATURE INPUT SHIFT -199,9 to 999,9 E.U. 0.0 Trim the PV to match an external reference source, linear 1 point methode

insh TEMPERATURE INPUT SHIFT UPPER LIMIT -199,9 to 999,9 E.U. 0.0 Trim the PV to match an external reference source, high point

insl TEMPERATURE INPUT SHIFT LOWER LIMIT -199,9 to 999,9 E.U. 0.0 Trim the PV to match an external reference source, low point

p PROPORTIONAL BAND 0,1 to 999,9 E.U. 8.0 *4 with E5CN-xxxL : P = 10% f.s.

43 ADJUSTMENT

i INTEGRAL TIME 0 TO 3999 SEC 233 If "I" = 0 then "of-r" (line 47) is 50% by default

44 LEVEL

d DIFFERENTIAL TIME 0 TO 3999 SEC 40 When RT is on (line 119) range is 0.0 to 999.9

c-sc COOLING COEFFICIENT 0,01 to 99,99 - 1.00 Only Heat/Cool operation. Balance control by adjusing cool output gain

c-db DEAD BAND -199,9 to 999,9 (-19.99 to 99.99 *4) E.U. 0.0 Only Heat/Cool operation. Area around 0% MV where MV is forced to 0%

of-r MANUAL RESET VALUE 0,0 to 100,0 % 50.0 Remove PV-SV offset in P or PD operation (available when I=0)

hys HYSTERESIS (OUT1) 0,1 to 999,9 (0.01 to 99.99 *4) E.U. 1.0 Only On/Off operation. Ouput OFF at SV, Output ON at SV - hys (0,1 for *4)

c-hys HYSTERESIS (OUT2) 0,1 to 999,9 (0.01 to 99.99 *4) E.U. 1.0 Only On/Off operation. Ouput OFF at SV, Output ON at SV + hys (0,1 for *4)

soak PROGRAM SOAK TIME 1 - 9999 m/h 0 Set time for Soak/Dwell here

wt-b PROGRAM WAIT BAND OFF, 0,1 to 999,9 E.U, off When the PV goes outside the band the Soak time is on WAIT

mv-s MANUAL VALUE AT STOP MV UPPER to LOWER LIMIT % 0.0 Forced output % when the controller is stopped (RUN/STOP)

mv-e MANUAL VALUE AT PV ERROR MV UPPER to LOWER LIMIT % 0.0 Forced output % when the sensor error break alarm is active

sprt SP RAMP SET VALUE OFF, 1 to 9999 E.U, off Maximum change of SV per minute or second (set with parameter #84)

ol-h MV UPPER LIMIT 0.0 to 105.0 % 105.0 0.0 is not valid when using standard control (-0.1 or 0.1 is used)

56 ol-l MV LOWER LIMIT

(-105.0) -5.0 to 0.0 (or

ol-h)

.-5.0 105.0 DEPENDING ON standard OR Heat & Cool Control

in-t INPUT TYPE 0 to 23 - 5 *3 *4 For Analogue Input Type (E5CN-xxxL) range = 0 - 4 default is 0

in-h SCALING UPPER LIMIT SCALE LOW+1 to 9999 E.U. 100 *1 Analogue input only

in-l SCALING LOWER LIMIT -1999 to SCALE HIGH -1 E.U. 0 *1 Analogue input only

dp DECIMAL POINT 0 to 1 - 0 Setting provides xxxx or xxx.x display (*4 = 0 to 4 decimal places)

d-u TEMPERATURE UNIT SELECTION C / F - °C Select degree Centigrade of Farenheit

sl-h SETVALUE UPPER LIMIT sl-l+1 to SENSOR High - 1300 *1 (Default Pt100 setting = 850 Default *4 setting 100)

sl-l SETVALUE LOWER LIMIT SENSOR Low to sl-h-1 - -200 *1 (Default *4 setting 0)

cntl CONTROL: PID - ON/OFF pid / onof - onof pid = 2PID - onof = ON/OFF

65 INITIAL

s-hc CONTROL: STANDARD - HEAT&COOL stnd / h-c - stnd stnd =Standard h-c=Heat&Cool (with H&C 2 alarms max, not 3)

66 SETTING

st ST SELF TUNING off / on - on on Starts AT on power-up and when <> st-b (line 95)

67 LEVEL

ptrn PROGRAM PATERN TYPE off / stop / cont - off type of programmer, OFF or Continue (run) / Stop (run) at end of soak/dwell

cp CONTROL PERIOD (OUT1) 0.5, 1 to 99 (steps of 1 sec) SEC 20 OUT1 duty cycle at 100% MV (heat)

c-cp CONTROL PERIOD (OUT2) 0.5, 1 to 99 (steps of 1 sec) SEC 20 OUT2 duty cycle at 100% MV (cool)

oreV DIRECT / REVERSE OPERATION or-r / or-d - or-r Usually REVERSE is for heat and DIRECT is for cool applications

alt1 ALARM 1 TYPE 0 to 12 - 2 *3 Alarm Type 1 is not shown when ptrn (line 67) is in use (Cont or Stop)

alt2 ALARM 2 TYPE 0 to 11 - 2 *3

alt3 ALARM 3 TYPE 0 to 11 - 2 *3

tr-t TRANSFER OUTPUT TYPE off sp sp-m pv mv c-mv - off Only for Linear Ouput models (E5CN-Cxxx-xxx)

tr-h TRANSFER OUTPUT UPPER LIMIT low to high of SP, MV or PV - 100.0 Only for Linear Ouput models (E5CN-Cxxx-xxx)

tr-l TRANSFER OUTPUT LOWER LIMIT low to high of SP, MV or PV - 0.0 Only for Linear Ouput models (E5CN-Cxxx-xxx)

o1-t LINEAR OUTPUT TYPE 0-20 / 4-20 mA 4-20 Only for Linear Ouput models (E5CN-Cxxx-xxx)

78 amoV MOVE TO ADVANCED FUNCTION SETTING LEVEL -1.999 to 9.999 - 0 Move to ADVANCED level with -169 (default factory setting)

NOT ALL PARAMETERS ARE SHOWN AT ALL TIMES ! !, ( DEPEND ON FUNCTION AVAILABLE OR SELECTED) BLUE: Input and PV

* 1 AFTER THE TEMPERATURE INPUT TYPE IS SET, THE UPPER AND LOWER SCALING VALUES CAN BE SET GREEN: Control / PID

* 2 PV IS FIXED RED OR FIXED GREEN OR GREEN>RED ON ALM1 OR RED>GREEN ON ALM1 PURPLE: Alarms

OR GREEN WITHIN STABLE BAND AND RED OUTSIDE OR AMBER BELOW, GREEN WITHIN AND RED ABOVE BAND GREY: MV / Output

* 3 MORE DETAILS AT THE BOTOM OF THIS OR THE OTHER SIDE PAGE YELLOW: SetValue SV/SP

* 4

alid for E5CN-xxxL-500 linear input models ORANGE: HA Heater Alarm (Burnout and SSR short)

new E5CN- Parameter List

NEW

Summary of content (2 pages)

PAGE 1
new E5CN- Parameter List NO. MODE 1 2 3 PROTECT 4 LEVEL 5 6 7 8 9 10 11 12 13 14 OPERATION 15 LEVEL 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 ADJUSTMENT 44 LEVEL 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 INITIAL 66 SETTING 67 LEVEL 68 69 70 71 72 73 74 75 76 77 78 DISPLAY pmov oapt icpt wtpt pmsk prlp a-m m-sp sp-m ct1 ct2 lcr1 lcr2 prst sktr r-s al-1 al1h al1l al-2 al2h al2l al-3 al3h al3l o c-o l.
PAGE 2
new E5CN- Parameter List NO.