Datasheet
E2E/E2EQ NEXT Series
17
XS5 NEXT Series XS5E2E/E2EQ NEXT Series
E2EQ NEXT Series (Spatter-resistant Long-distance type)
DC 2-wire
*1. Use the Sensor within the range in which the setting indicator (green LED) is ON (except D2 Models).
*2. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard
sensing object, and a set distance of half the sensing distance.
*3. The IP67G is the degree of protection which is defined according to the JIS (Japanese Industrial Standards).
The IP67 indicates the same level of protection as defined by the IEC, and the G indicates that a device has resistance to oil.
Size M8 M12 M18 M30
Shielded Shielded
Item Model E2EQ-X3D@ E2EQ-X7D@ E2EQ-X11D@ E2EQ-X20D@
Sensing distance 3 mm ±10% 7 mm ±10% 11 mm ±10% 20 mm ±10%
Setting distance *1 0 to 2.4 mm 0 to 5.6 mm 0 to 8.8 mm 0 to 16 mm
Differential travel 15% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 19.)
Standard sensing object Iron, 9 × 9 × 1 mm Iron, 21 × 21 × 1 mm Iron, 33 × 33 × 1 mm Iron, 60 × 60 × 1 mm
Response frequency *2 250 Hz 250 Hz 250 Hz 200 Hz
Power supply voltage 10 to 30 VDC, (including 10% ripple (p-p))
Leakage current 0.8 mA max.
Control output
Load current 3 to 100 mA
Residual voltage
Polarity: 3 V max. (Load current: 100 mA, Cable length: 2 m)
No polarity: 5 V max. (Load current: 100 mA, Cable length: 2 m)
Indicator
D1 Models: Operation indicator (orange), Setting indicator (green)
D2 Models: Operation indicator (orange)
Operation mode
D1 Models: NO
D2 Models: NC
Protection circuits Surge suppressor, Load short-circuit protection
Ambient temperature range Operating: -25 to 70°C, Storage: -40 to 85°C (with no icing or condensation)
Ambient humidity range Operating and Storage: 35% to 95% (with no condensation)
Temperature influence
±10% max. of sensing distance at 23°C
in the temperature range of -25 to 70°C
±20% max. of sensing distance at 23°C
in the temperature range of -25 to 70°C
Voltage influence ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range
Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case
Vibration resistance (destruction) 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance (destruction)
500 m/s
2
10 times each in
X, Y, and Z directions
1,000 m/s
2
10 times each in X, Y, and Z directions
Degree of protection Pre-wired Models/Pre-wired Connector Models: IP67 (IEC 60529) and IP67G *3 (JIS C 0920 Annex 1)
Connecting method Pre-wired Models (Standard cable length: 2 m) and Pre-wired Connector Models (Standard cable length: 0.3 m)
Weight
(packed state)
Pre-wired Models Approx. 60 g Approx. 70 g Approx. 150 g Approx. 210 g
Pre-wired Connector
Models
Approx. 30 g Approx. 40 g Approx. 90 g Approx. 140 g
Materials
Case Fluororesin coating (Base material: brass)
Sensing surface Fluororesin
Clamping nuts Fluororesin coating (Base material: brass)
Toothed washer Zinc-plated iron
Cable Vinyl chloride (PVC)
Accessories Instruction manual, Clamping nuts, Toothed washer
Refer to the timing charts under I/O Circuit Diagrams on page 22 for details.