Datasheet

E2E/E2EQ NEXT Series
16
Ratings and Specifications
E2E NEXT Series (Long-distance type)
DC 2-wire
*1. Use the Sensor within the range in which the setting indicator (green LED) is ON (except D2 Models).
*2. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard
sensing object, and a set distance of half the sensing distance.
*3. The IP67G is the degree of protection which is defined according to the JIS (Japanese Industrial Standards).
The IP67 indicates the same level of protection as defined by the IEC, and the G indicates that a device has resistance to oil.
*4. The Oil-resistant Component Evaluation Standards are OMRON's own durability evaluation standards.
2-year oil resistance indicates the median value of the product design and the oil-resistance performance criterion result (=Typical value).
The Pre-wired Connector Model verifies 2 years of oil resistance when mating with Round Oil-resistant Connectors XS5 NEXT series correctly.
The degree of protection is not satisfied with the part where cable wires are uncovered for the Pre-wired Models.
Size M8 M12 M18 M30
Shielded Shielded Unshielded Shielded Unshielded Shielded Unshielded Shielded Unshielded
Item Model E2E-X3D@ E2E-X6MD@ E2E-X7D@ E2E-X10MD@ E2E-X11D@ E2E-X20MD@ E2E-X20D@ E2E-X40MD@
Sensing distance 3 mm ±10% 6 mm ±10% 7 mm ±10% 10 mm ±10% 11 mm ±10% 20 mm ±10% 20 mm ±10% 40 mm ±10%
Setting distance *1 0 to 2.4 mm 0 to 4.8 mm 0 to 5.6 mm 0 to 8 mm 0 to 8.8 mm 0 to 16 mm 0 to 16 mm 0 to 32 mm
Differential travel 15% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 19.)
Standard sensing object
Iron,
9 × 9 × 1 mm
Iron,
18 × 18 × 1 mm
Iron,
21 × 21 × 1 mm
Iron,
30 × 30 × 1 mm
Iron,
33 × 33 × 1 mm
Iron,
60 × 60 × 1 mm
Iron,
60 × 60 × 1 mm
Iron,
120 × 120 × 1 mm
Response frequency *2 350 Hz 250 Hz 350 Hz 200 Hz 250 Hz 200 Hz 200 Hz 50 Hz
Power supply voltage 10 to 30 VDC, (including 10% ripple (p-p))
Leakage current 0.8 mA max.
Control
output
Load current 3 to 100 mA
Residual
voltage
Polarity: 3 V max. (Load current: 100 mA, Cable length: 2 m)
No polarity: 5 V max. (Load current: 100 mA, Cable length: 2 m)
Indicator
D1 Models: Operation indicator (orange), Setting indicator (green)
D2 Models: Operation indicator (orange)
Operation mode
D1 Models: NO
D2 Models: NC
Protection circuits Surge suppressor, Load short-circuit protection
Ambient temperature
range
Operating: -25 to 70°C, Storage: -40 to 85°C (with no icing or condensation)
Ambient humidity range Operating and Storage: 35% to 95% (with no condensation)
Temperature influence
±10% max. of sensing distance at 23°C
in the temperature range of -25 to 70°C
±20% max. of
sensing
distance at
23°C in the
temperature
range of
-25 to 70°C
±10% max. of
sensing
distance at
23°C in the
temperature
range of
-25 to 70°C
±20% max. of sensing distance
at 23°C in the temperature
range of -25 to 70°C
Voltage influence ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range
Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case
Vibration resistance
(destruction)
10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance
(destruction)
500 m/s
2
10 times each in X, Y,
and Z directions
1,000 m/s
2
10 times each in X, Y, and Z directions
Degree of protection
Pre-wired Models/Pre-wired Connector Models: IP67 (IEC 60529), IP67G
*3 (JIS C 0920 Annex 1) Passed OMRON's Oil-resistant
Component Evaluation Standards
*4 (Cutting oil type: specified in JIS K 2241:2000, Temperature: 35 °C max.) and IEC 60529 (old
standard: DIN 40050 PART9) IP69K
Connecting method Pre-wired Models (Standard cable length: 2 m) and Pre-wired Connector Models (Standard cable length: 0.3 m)
Weight
(packed
state)
Pre-wired
Models
Approx. 60 g Approx. 70 g Approx. 130 g Approx. 150 g Approx. 180 g Approx. 210 g
Pre-wired
Connector
Models
Approx. 30 g Approx. 40 g Approx. 70 g Approx. 90 g Approx.110 g Approx. 140 g
Materials
Case
Nickel-plated
brass
Stainless steel
(SUS303)
Nickel-plated brass
Sensing surface Polybutylene terephthalate (PBT)
Clamping nuts Nickel-plated brass
Toothed washer Zinc-plated iron
Cable Vinyl chloride (PVC)
Accessories Instruction manual, Clamping nuts, Toothed washer
Refer to the timing charts under I/O Circuit Diagrams on page 22 for details.