Datasheet

ManualsBrandsOmron Industrial Automation ManualsAutomationLimit Switch, Short Hinge Roller Lever, 1NC + 1NO,

Enclosed Switch D4MC

Economical, High Utility Enclosed

Switch

High precision and long life (10,000,000 mechani-

cal

operations) through employment of the moving

spring used in OMRON Z Basic Switch.

Sealed with gasket diaphragm to provide high

sealing

property without use

of any adhesive or pin.

Suitable for applications demanding higher me-

chanical

strength, dustproof and drip-proof proper

ties than those on basic switches.

Panel mount versions have the same operating

position as Z Basic Switch.

Resin molded terminal versions are available.

Ordering Information

Model Number Legend

D4MC-

1. Actuator

5000:

Panel mount plunger

5020:

Panel mount roller plunger

5040:

Panel mount crossroller plunger

1020:

Short hinge lever

1000:

Hinge lever

2000:

Hinge roller lever

2020:

Short hinge roller lever

3030:

One-way action short hinge roller lever

List of Models

Actuator Model

Panel

mount plunger

D4MC-5000

Panel mount roller plunger

D4MC-5020

Panel mount crossroller plunger

D4MC-5040

Short hinge lever

D4MC-1020

Hinge lever

D4MC-1000

Hinge roller lever

D4MC-2000

Short hinge roller lever

D4MC-2020

One-way action short hinge roller lever

D4MC-3030

Note: 1.

Use molded terminal models (refer to page 209) when using the Switch under one of the following conditions:

a) dusty

, b) high amount of dripping oil, or c) high humidity

Micro-load models are available.

e.g. Standard model

Micro-load model

D4MC-5020 D4MC-5020-C

Summary of content (7 pages)

PAGE 1
Enclosed Switch D4MC Economical, High Utility Enclosed Switch High precision and long life (10,000,000 mechanical operations) through employment of the moving spring used in OMRON Z Basic Switch. Sealed with gasket diaphragm to provide high sealing property without use of any adhesive or pin. Suitable for applications demanding higher mechanical strength, dustproof and drip-proof properties than those on basic switches. Panel mount versions have the same operating position as Z Basic Switch.
PAGE 2
D4MC D4MC Specifications Ratings Rated voltage Non-inductive load Resistive load NC Inductive load Lamp load NO NC Inductive load NO NC Motor load NO NC NO 125 VAC 10 A 3A 1.5 A 10 A 5A 2.5 A 250 VAC 10 A 2.5 A 1.25 A 10 A 3A 1.5 A 480 VAC 3A 1.5 A 0.75 A 2.5 A 1.5 A 0.75 A 8 VDC 10 A 3A 1.5 A 6A 5A 2.5 A 14 VDC 10 A 3A 1.5 A 6A 5A 2.5 A 30 VDC 6A 3A 1.5 A 5A 5A 2.5 A 125 VDC 0.5 A 0.4 A 0.05 A 0.05 A 250 VDC 0.25 A 0.2 A 0.03 A 0.
PAGE 3
D4MC D4MC Characteristics Degree of protection IP67 (NEMA250: 6.6P) Life expectancy Mechanical: 10,000,000 operations min. Electrical: 500,000 operations min. Operating speed 0.05 mm/s to 0.5 m/s (at panel mount plunger) Operating frequency Mechanical: 120 operations/min Electrical: 20 operations/min Insulation resistance 100 MΩ min. (at 500 VDC) Contact resistance 15 mΩ max.
PAGE 4
D4MC D4MC Engineering Data (Reference Data) 10,000 Electrical Life Expectancy Operating temperature: 20±2°C Operating humidity: 65±5% No load Operating frequency: 120 operations/min 5,000 Life expectancy (x 104 operations) Life expectancy (x 104 operations) Mechanical Life Expectancy (D4MC-5000) 2,000 1,000 500 200 100 0.01 0.02 0.05 0.1 0.2 0.5 1 2 5 10,000 7,000 5,000 125 VAC cosφ=1 3,000 125 VAC cosφ=0.4 250 VAC cosφ=1 1,000 700 500 250 VAC cosφ=0.
PAGE 5
D4MC D4MC Panel Mount Crossroller Plunger D4MC-5040 M12 x 1 mounting screw Two hexagon nuts (thickness: 3 width: 17) (See note 2) 12.7 dia. × 5 (see note 1) Note: 16 dia. 1. Stainless steel roller 2. The length of the imperfect threads is 1.5 mm maximum. 22 max. (21 x 21) Terminal protective cover Short Hinge Lever D4MC-1020 Two, 4.3±0.1 dia. mounting holes Seal rubber (NBR) t = 1 (see note) Note: Stainless steel lever 22 max.
PAGE 6
D4MC D4MC One-way Action Short Hinge Roller Lever D4MC-3030 t=1 (see note 1) 12.7 dia. × 7.5 (see note 2) 14 Angle of roller swing: 90° Note: 1. Stainless steel lever 2. Plastic roller 22 max. 15 Terminal protective cover (21 x 21) Two, 4.3±0.1 dia. mounting holes Seal rubber (NBR) Mounting Holes Two 4.3 dia. mounting holes or M4 screw holes 25.4 ± 0.
PAGE 7
D4MC D4MC Precautions Mounting Correct Use Operating Method Excessive dog angle, operating speed, or overtravel (OT) may damage the actuator. Check that OT has a sufficient margin. The actual OT should be rated OT x 0.7 to 1. When mounting the Switch with screws on a side surface, fasten the Switch with M4 screws and use washers, spring washers, etc., to ensure secure mounting. Mounting Holes Handling • Do not expose the Switch to water exceeding 60°C or use it in Two, 4.3-dia.