Datasheet

A16
16
Specifications
Approved Standard Ratings
Ratings
Switch Ratings
Minimum applicable load: 1 mA at 5 VDC
Rated values are obtained from tests conducted under the following
conditions.
1. Load: Resistive load
2. Mounting conditions: No vibration and no shock
3. Temperature: 20 ±2°C
4. Operating frequency: 20 operations/min
Contact Form
Super-bright LED
Incandescent Lamp
Voltage-reduction Unit (LED Lamp)
Characteristics
Socket Unit
*1. Set and reset constitute one operation.
*2. With LED and incandescent lamp not mounted.
*3. Degree of protection from the front of the panel.
Screw-less Clamp
Operating Characteristics
* Alternate operation models only.
UL, cUL (File No. E41515) TÜV (EN60947-5-1) (Low Voltage Directive)
CCC (GB14048.5)
5 A at 125 VAC, 3 A at 250 VAC (general use)
3 A at 30 VDC (resistive)
Note: Certification has been obtained for the Switch.
For detailed information on individual products that
have received certification, consult your supplier.
3 A at 250 VAC
3 A at 30 VDC
5 A at 125 VAC
3 A at 250 VAC
3 A at 30 VDC
Rated voltage Resistive load
125 VAC 5 A
250 VAC 3 A
30 VDC 3 A
Name Contact
DPDT
COM
NC
NO
Rated
voltage
Rated
current
Operating
voltage
Internal limiting resistor
5 VDC
8 mA
5 VDC ±5%
Red, yellow, white: 300 Ω
Green, blue, pure white: 160 Ω
12 VAC/VDC 12 VAC/VDC ±5%
Red, yellow, white: 1 kΩ
Green, blue, pure white: 910 Ω
24 VAC/VDC 24 VAC/VDC ±5% 2.4 kΩ
Rated voltage Rated current Operating voltage
6 VAC/VDC 60 mA 5 VAC/VDC
14 VAC/VDC 40 mA 12 VAC/VDC
28 VAC/VDC 24 mA 24 VAC/VDC
Rated voltage Operating voltage Applicable lamp
110 VAC/VDC
100/110 VAC/VDC
(90 to 121 V)
A16-24DS@
LED Lamp
220 VAC/VDC
200/220 VAC/VDC
(180 to 242 V)
Item Type Pushbutton Switch
Allowable
operating
frequency
Mechanical
Momentary operation: 120 operations/minute max.
Alternate operation: 60 operations/minute max. *1
Electrical 20 operations/minute max. *1
Insulation resistance 100 MΩ min. (at 500V DC)
Contact resistance 100 mΩ max. (initial value)
Dielectric
strength
Between terminals
of same polarity
1,000 VAC, 50/60 Hz for 1 minute
Between terminals
of different polarity
2,000 VAC, 50/60 Hz for 1 minute
Between each ter-
minal and ground
2,000 VAC, 50/60 Hz for 1 minute
Between lamp ter-
minals
1,000 VAC, 50/60 Hz for 1 minute *2
Vibration
resistance
Malfunction
10 to 55 Hz, 1.5-mm double amplitude
(malfunction within 1 ms)
Shock
resistance
Destruction 500 m/s
2
max.
Malfunction 150 m/s
2
max. (malfunction within 1 ms)
Durability
Mechanical
Momentary operation: 2,000,000 operations min.
Alternate operation: 200,000 operations min. *1
Electrical 100,000 operations min. *1
Electric shock protection class Class II
PTI (tracking characteristic) 175
Degree of contamination 3 (IEC947-5-1)
Weight
Approx. 10 g (in the case of a lighted
DPDT switch with solder terminals)
Degree of protection IP40: A16, Oil-resistant IP66: A165 *3
Ambient operating temperature –10 ° C to 55 ° C (with no icing or condensation)
Ambient operating humidity 35% to 85%RH
Ambient storage temperature –25 ° C to 65 ° C (with no icing or condensation)
Item Screw-Less Clamp
Recommended wire size 0.5 mm
2
twisted wire or 0.8 mm-dia. solid wire
Usable wires
and tensile
strength
Twisted
wire
0.3 mm
2
0.5 mm
2
0.75 mm
2
1.25 mm
2
Solid
wire
0.5 mm
dia.
0.8 mm
dia.
1.0 mm
dia.
—
Tensile
strength
10 N 20 N 30 N 40 N
Length of exposed wire 10 ±1mm
Compliant standards JIS C 2811 Terminal Blocks for Industrial Use
Type Pushbutton Switch
Characteristics IP40 Oil-resistant IP66
Operating force (OF) max. 4.41 N 4.91 N
Releasing force (RF) min. 0.29 N
Total travel (TT) Approx. 3 mm
Pretravel (PT) max. 2.5 mm
Lock travel alternate (LTA) min. * 0.5 mm