262640 HEM-711 EN_SP_r2.
62640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 2 TABLE OF CONTENTS Before Using the Unit Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Operating the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Risk of Electrical Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Care and Maintenance . . . . . . . .
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 3 Before Using the Unit INTRODUCTION Thank you for purchasing the Omron® HEM-711DLX IntelliSense® Automatic Blood Pressure Monitor with ComFitTM Cuff. Fill in for future reference. DATE PURCHASED: __________________ SERIAL NUMBER: ____________________ Staple your purchase receipt here Your new digital blood pressure monitor uses the oscillometric method of blood pressure measurement.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 4 SAFETY INFORMATION To assure the correct use of the product basic safety measures should always be followed including the warnings and cautions listed in this instruction manual. SAFETY SYMBOLS USED IN THIS INSTRUCTION MANUAL WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 5 SAFETY INFORMATION OPERATING THE DEVICE (continued) Operate the device only as intended. Do not use the device for any other purpose. Dispose of the device, components and optional accessories according to applicable local regulations. Unlawful disposal may cause environmental pollution. Do not use a cellular phone near the device. It may result in an operational failure. Use only Omron authorized parts and accessories.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 6 SAFETY INFORMATION CARE AND MAINTENANCE Do not subject the monitor to strong shocks, such as dropping the unit on the floor. Do not submerge the device or any of the components in water. Store the device and the components in a clean, safe location. Changes or modification not approved by Omron Healthcare will void the user warranty. Do not disassemble or attempt to repair the unit or components.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 7 BEFORE TAKING A MEASUREMENT To ensure a reliable reading follow these recommendations: 1. Avoid eating, drinking alcohol, smoking, exercising, and bathing for 30 minutes before taking a measurement. Rest for at least 15 minutes before taking the measurement. 2. Stress raises blood pressure. Avoid taking measurements during stressful times. 3. Measurements should be taken in a quiet place. 4. Remove tight-fitting clothing from your arm. 5.
262640 HEM-711 EN_SP_r2.
262640 HEM-711 EN_SP_r2.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 10 DISPLAY SYMBOLS IRREGULAR HEARTBEAT SYMBOL ( ) When the monitor detects an irregular rhythm two or more times during the measurement, the Irregular Heartbeat Symbol ( ) will appear on the display with the measurement values. An irregular heartbeat rhythm is defined as a rhythm that is more than 25 % slower or 25 % faster from the average rhythm detected while the monitor is measuring the systolic blood pressure and the diastolic blood pressure.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 11 DISPLAY SYMBOLS The American Heart Association1 recommends the following guideline for upper limit of normal for home blood pressure readings: AHA Home Guideline for Upper Limit of Normal BP Systolic Blood Pressure 135 mmHg Diastolic Blood Pressure 85 mmHg This is a general guideline because blood pressure depends on age and morbidity.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 12 DISPLAY SYMBOLS USING THE MEMORY FUNCTION The Heartbeat Symbol flashes when the blood pressure reading stored in the memory is above 135 for the Systolic Blood Pressure value and/or 85 for the Diastolic Blood Pressure value.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 13 BATTERY INSTALLATION 1. Press the ▼ indicator on the battery cover and slide the cover off in the direction of the arrow. 2. Install 4 “AA” size batteries so the + (positive) and - (negative) polarities match the polarities of the battery compartment as indicated. Battery Cover − ＋ 3. Replace the battery cover.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 14 BATTERY INSTALLATION BATTERY REPLACEMENT Low Battery Indicator When the Low Battery Indicator appears on the display screen turn the monitor off and remove all the batteries. Replace with four new batteries at the same time. Longlife alkaline batteries are recommended. CAUTION If battery fluid should get in your eyes, immediately rinse with plenty of clean water. Contact a physician immediately.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 15 USING THE AC ADAPTER NOTES: • Use only the authorized Omron AC Adapter, Model Number HEM-ADPT1,with this monitor. • We recommend you install the batteries even if the AC Adapter is used. If no batteries are installed, you may need to reset the date and time if the AC Adapter is disconnected. The measurement results will not be deleted. CAUTION Use only Omron authorized parts and accessories.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 16 SETTING THE DATE AND TIME Set the monitor to the current date and time before taking a measurement for the first time. If the date and time are not set correctly, the measurement values stored in the memory and the average values may not be correct. The Blood Pressure Monitor automatically stores up to 60 individual measurements values with the dates and times.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 17 SETTING THE DATE AND TIME 2. SETTING THE YEAR The year can be set between 2006 and 2030. When the display reaches 2030, it will return to 2006. START STOP Press the MEMORY button to advance by increments of one year. Press the Date/Time Setting button to set the current year. STOP The month flashes on the display. NOTE: Press and hold the MEMORY button to advance the date and time values faster. 3.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 18 SETTING THE DATE AND TIME 4. SETTING THE DAY Press the MEMORY button to advance by increments of one day. Press the Date/Time Setting button to set the current day. STOP The hour flashes on the display. 5. SETTING THE HOUR The time is set using AM or PM. Press the MEMORY button to advance by increments of one hour. Press the Date/Time Setting button to set the current hour. The minute flashes on the display. 6.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 19 APPLYING THE ARM CUFF CAUTION Read all of the information in the instruction manual and any other literature in the box before operating the unit. CAUTION This device is intended for use in measuring blood pressure and pulse rate in the adult population. Do not use this device on infants or persons who cannot express their intentions. APPLYING THE CUFF ON THE LEFT ARM 1. Make sure the air plug is securely inserted in the main unit. 2.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 20 APPLYING THE ARM CUFF 3. Sit in a chair with your feet flat on the floor. Place your left arm on a table so the cuff is level with your heart. Thumb Grip 4. Hold the grip on the cuff securely with your right hand, placing your thumb on the thumb grip. 5. Turn the palm of your left hand upward.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 21 APPLYING THE ARM CUFF 6. Apply the cuff to your left upper arm so the blue strip is on the inside of your arm and aligned with your middle finger. The air tube runs down the inside of your arm. The bottom of the cuff should be approximately 1/2" above your elbow. Blue Strip 1/2 inch (1 - 2 cm) Air Tube 7. Wrap the cuff firmly in place around your arm using the cloth strip.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 22 APPLYING THE ARM CUFF APPLYING THE CUFF ON THE RIGHT ARM Apply the cuff to your right upper arm so the thumb grip is centered on the inside of your inner arm. The bottom of the cuff should be approximately 1/2'' above your elbow. Thumb Grip NOTE: Be careful not to rest your arm on the air tube. This will restrict the flow of air to the cuff.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 23 TAKING A MEASUREMENT The monitor automatically determines your ideal inflation level. In rare circumstances when a higher inflation may be necessary, the monitor automatically re-inflates the cuff up to 30 mmHg higher than the initial inflation and restarts the measurement. CAUTION Operate the device only as intended. Do not use the device for any other purpose. 1. Press the START/STOP button. All symbols appear on the display.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 24 TAKING A MEASUREMENT 2. Inflation stops automatically and the measurement is started. As the cuff deflates, decreasing numbers appear on the display. The Heartbeat Symbol ( ) flashes at every heartbeat. 3. When the measurement is complete, the arm cuff completely deflates. Your blood pressure and pulse rate are displayed. 4. Press the START/STOP button to turn the monitor off.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 25 TAKING A MEASUREMENT SPECIAL CONDITIONS CAUTION Inflating to a higher pressure than necessary may result in bruising where the cuff is applied. If your systolic pressure is known to be more than 220 mmHg, press and hold the START/STOP button until the monitor inflates 30 to 40 mmHg higher than your expected systolic pressure. START STOP NOTES: • Do not apply more pressure than necessary. • The monitor will not inflate above 299 mmHg.
2640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 26 USING THE MEMORY FUNCTION The monitor is designed to store the blood pressure and the pulse rate in the memory every time a measurement is completed. The monitor automatically stores up to 60 sets of measurement values (blood pressure and pulse rate). When 60 sets of measurement values are stored, the oldest record is deleted to save the most recent values.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 27 USING THE MEMORY FUNCTION TO DISPLAY THE MEASUREMENT VALUES 1. Press the MEMORY button. STOP The Average Symbol ( ) appears on the display when the average reading is shown. 2. Press the MEMORY button to display the measurement values from the most recent to the oldest. 3. Press the START/STOP button to turn the power off. NOTES: • Press the MEMORY button to display the next values. • Press and hold the MEMORY button to display the values faster.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 28 USING THE MEMORY FUNCTION TO DELETE ALL VALUES STORED IN THE MEMORY You cannot partially delete values stored in the memory. All values will be deleted. 1. While holding the MEMORY button and the START/STOP button simultaneously for more than 2 seconds all values will be deleted.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 29 CARE AND MAINTENANCE To keep your digital blood pressure monitor in the best condition and protect the unit from damage, follow the directions listed below: Keep the monitor in the storage case when not in use. Make sure the AC adapter is placed in the storage case as illustrated to avoid damage to the display. Avoid kinking or sharply bending the AC Adapter cord. Do not forcefully bend the arm cuff or air tube. Do not fold tightly.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 30 CARE AND MAINTENANCE Remove the batteries if the unit will not be used for three months or longer. Always replace all the batteries with new ones at the same time. Use the unit consistent with the instruction provided in this manual. Use only authorized parts and accessories. CAUTION Changes or modification not approved by Omron Healthcare will void the user warranty. Do not disassemble or attempt to repair the unit or components.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 31 ERROR INDICATORS AND TROUBLESHOOTING TIPS ERROR INDICATORS SYMBOL CAUSE CORRECTION Monitor could not detect pulse wave. Take another measurement and remain still until the measurement is complete. Air plug is not connected. Cuff under-inflated. Cuff not applied correctly. Remove the arm cuff. Read “Taking a Measurement”. Take another measurement. Cuff over-inflated Replace the four batteries. Refer to “Battery Installation.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 32 ERROR INDICATORS AND TROUBLESHOOTING TIPS TROUBLESHOOTING TIPS PROBLEM CAUSES AND SOLUTIONS No power. Replace all four batteries with new ones. No display appears on the unit. Check the battery installation for proper placement of the battery polarities. Measurement values appear too high or too low. Blood pressure varies constantly. Many factors including stress, time of day, and how you wrap the cuff, may affect your blood pressure.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 33 FCC STATEMENT NOTE: POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for U.S.A. only) This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 34 WARRANTY Your HEM-711DLX, IntelliSense® Automatic Blood Pressure Monitor, excluding the arm cuff, is warranted to be free from defects in materials and workmanship appearing within 5 years from the date of purchase, when used in accordance with the instructions provided with the monitor.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 11:33 AM Page 35 SPECIFICATIONS HEM-711DLX LCD Digital Display Pressure: 0 to 299 mmHg, Pulse: 40-180/min.
262640 HEM-711 EN_SP_r2.qxp 1/15/07 Manufactured by OMRON HEALTHCARE Made in China Distributed by: OMRON HEALTHCARE, INC. 1200 Lakeside Drive Bannockburn, Illinois 60015 www.omronhealthcare.com Copyright © 2007 Omron Healthcare, Inc.
