Datasheet

11
B5T Human Vision Components (HVC-P2)
B5T
Check the Product for physical damage upon opening its pack-
age. It is recommended to wear gloves when opening the pack-
age.
Follow the indications listed below for a safe use of the Product.
(1) Installation Environment
• There is potential internal deterioration and damage of internal
parts of the Device. Do not use the Product in conditions
exceeding the ratings for temperature and humidity.
• Do not use the Product in an environment where condensation
occurs.
• Do not use the Product in an environment subjected to water,
oil or chemicals spills.
• Do not use the Product in an environment subjected to corro-
sive, combustible or explosive gas.
• Do not use the Product in an environment where dust, salt or
iron powder are present.
(2) Power Supply and Wiring
• Make sure there is no faulty wiring of I/O terminals, etc. as this
may result in fire.
• Do not connect the DC power supply terminal to AC power.
• Do not connect the Product to DC voltage above the rated
capacity.
• Do not reverse-connect the DC power supply.
• Make sure to turn the Device off before removing cables.
• Do not connect the UART connector (CN5) to asynchronous
method non-compliant devices.
• Make sure to check the Device and the connector pins for dis-
tortion or physical damage before connecting or removing
cables.
• Connect a commercially available Micro USB Cable (TypeB)
cable to the USB connector (CN3). Make sure the cable is not
damaged and do not modify it.
(3) Others
• Do not disassemble, repair or otherwise remodel the Device.
• Treat the Product as industrial waste when disposing of it.
• Use the M2 screws on the fixing holes on the Device when fix-
ing it. Make sure not to bend or break the board when fasten-
ing the screws. Apply torque appropriately for the screws
used.
• Do not apply stress on the Device, e.g. twists, deflections or
impacts, as it may result in causing defects or degradation.
• Do not apply stress on the connector or display implementa-
tion parts when installing the Device, as it may result in caus-
ing defects or degradation.
Observe the following precautions to prevent failure to operate
and malfunctions, and to prevent adversely affecting the perfor-
mance and function of the Product.
• Store the Device at a temperature between -30 and +70°C and
a humidity level below 90%.
• Do not touch the board mounted parts with bare hands. Dis-
charge any static electricity from the user before use.
• Take proper measures against static electricity by using an
antistatic wrist strap, etc. before handling the Product.
• Make sure to properly ground the connector's earth terminal in
order to prevent malfunction due to noise.
• Do not use the Product in places where the surrounding tem-
perature goes above the rating range.
• Do not use the Product in a location where it would be sub-
jected to direct sunlight.
• Do not use the Product in a location subject to excessive
inductive or power supply noise, such as in strong magnetic or
electric fields.
• Do not use the Product in a location where it would be sub-
jected to strong UV light.
• Do not use the Product in a location where it would be sub-
jected to radiation.
• Sufficiently evaluate the electrical characteristics of any con-
nection to the Device.
• Make sure to properly align the connectors when connecting
them.
• Avoid desorption of power supplied connectors as it will result
in accidents.
• Refer to the B5T-007001 Command Specifications document
separately provided by OMRON for details on the interface
specifications.
• Never use benzene, paint thinner, or any other volatile clean-
ing solution, detergent, bleach or chemical washcloth for
cleaning the Device.
• Take in consideration heat dissipation from the Device when
installing it in order to improve its long term reliability.
• Install the Device sufficiently far away from any other sur-
rounding charged parts.
• Install the Device making sure not to obstruct the camera
detection range.
• Use transparent materials to cover and protect the front of the
lens should it be in contact with hands or objects.
• Remove the lens protective seal before use (B5T-007001-
010).
• Remove the lens protective cover before use (B5T-007001-
020).
• Do not touch the camera module.
• The Product performs detection on images. As such, note that
it may sometimes detect objects other than living bodies, such
as photographs or posters.
• Note that since the Product uses a camera for detection, suc-
cessful detection may not be possible due to light orientation,
brightness or exposure issues.
• Make sure to reset the Product before using it again following
a power interruption or failure.
• Restart or reset the Device if data is received improperly.
• Cutting or losing power to the Device while saving the Album
on the flash ROM may destroy the Album data saved on it. As
such, make sure to take a backup of the Album data on the
Host device. Refer to the B5T-007001 Command Specifica-
tions document for details.
• Do not use the USB and UART connection method simultane-
ously.
• Do not remove the FFC connection between the main board
and the camera board, and do not alter the configuration of the
combination.
• When using the USB connector, note that the bus power may
not be properly powering the Device depending on the com-
puter USB port used. In such case, use a device like a self-
powered hub with an AC adaptor.
Precautions for Safe Use
Precautions for Safe Use