iConverter® 19-Module Power Chassis User Manual 140 Technology Drive, #500, Irvine, CA 92618 Phone: (949) 250-6510; Fax: (949) 250-6514
Warning The operating description in this Instruction Manual is for use by qualified personnel only. To avoid electrical shock, do not perform any servicing of this unit other than that contained in the operating instructions, unless you are qualified and certified to do so by Omnitron Systems Technology, Inc. Caution All user-required operations can be performed without opening the unit. Never attempt to open or remove the cover or tamper with the unit.
iConverter 19-Module Power Chassis User Manual 1. 0 GENERAL DESCRIPTION The iConverter 2U (3.5 inch) 19-Module Power Chassis is powered by up to three (3) hot-swappable and redundant universal AC or DC power supplies and can accommodate up to nineteen iConverter media converters. It is ideal for enterprise Local Area Network (LAN) or Metropolitan Area Network (MAN) applications where managed media converters with high density and a small rack-footprint (2U) are important. Fig.
Fig. 2 19-Module Backplane Architecture Fig. 2 depicts the chassis’ backplane architecture including the A and B Links. The A Links connect between odd numbered slots on the left to even numbered slots on the right (i.e. 1-2, 3-4, 5-6, 7-8, 9-10, 11-12, 13-14, 15-16, 17-18). The B Links connect between even numbered slots on the left to odd numbered slots on the right (i.e. 2-3, 4-5, 6-7, 8-9, 10-11, 12-13, 14-15, 16-17, 18-19).
This configuration provides the network administrator with the ability to provide multi-customer service using a single chassis which is securely managed. 2.0 UNPACKING, VISUAL INSPECTION AND INVENTORY Review the contents.
Fig. 5 Attaching Grounding Lug to Chassis Attach one end of the ground cable to the chassis ground point using the appropriate bolts and dual-hole grounding lug connector (not provided). See Figure 5. Attach the other end of the ground cable to the office equipment using a dual-hole grounding lug connector according to the office equipment specifications. The standard operating temperature of this equipment is 0 to 50 degrees C.
WARNING: Only a DC power source that complies with safety extra low voltage (SELV) requirements can be connected to the DC-input power supply. o o o o WARNING REGARDING EARTHING GROUND: This equipment shall be connected to the DC supply system earthing electrode conductor or to a bonding jumper from an earthing terminal bar or bus to which the DC supply system earthing electrode is connected.
4.0 POWER SUPPLY REPLACEMENT CAUTION: To remove power from the chassis, remove power cord from all power supplies. WARNING!!! NEVER ATTEMPT TO OPEN THE CHASSIS OR SERVICE THE POWER SUPPLY OR FAN MODULE. OPENING THE CHASSIS MAY CAUSE SERIOUS INJURY OR DEATH. THERE ARE NO USER REPLACEABLE OR SERVICEABLE PARTS IN THIS UNIT. The power supplies are hot swappable and can be replaced without shutting the chassis down.
the power supply is seated firmly against the backplane and tighten the thumb screws securely with a screwdriver. Locate the DC circuit breaker and make sure that the switch is in the OFF position. Reconnect the DC power source to the iConverter power supply. Locate the DC circuit breaker and switch the circuit breaker to the ON position. Watch and listen to the fan in the rear of the power supply to ensure it is powered.
5.0 SPECIFICATIONS Chassis Type 19-Module AC 19-Module AC 19-Module 24VDC 19-Module 48VDC 19-Module 48VDC Model Number 8200-x 8201-x 8206-x 8205-x 8207-x Module Capacity 19 Power Supply Capacity Power Requirements (typical) 1 - 3 Power Supplies 60 watts 120 watts 66 watts 66 watts 120 watts 100 to 240VAC 50/60Hz 2.0A @ 100VAC 100 to 240VAC 50/60Hz 2.5A @ 100VAC +/- 18 to 36VDC 2.0A @ 100VAC +/- 36 to 60VDC 3.0A @ 100VAC +/- 36 to 60VDC 5.0A @ 100VAC 18A @ 3.3VDC 36A @ 3.
