Instruction Manual

ManualsBrandsOmnitron Systems Technology ManualsCommunicationmiConverter GX

Page 15

Page 10 Page 11 Page 12Page 9

Page 14 Page 16

SPECIFICATIONS:

Form: 040-12000-001E 1/13

Warning

The operating description in this Instruction Manual is

for use by qualied personnel only. To avoid electrical

shock, do not perform any servicing of this unit other

than that contained in the operating instructions, unless

you are qualied and certied to do so by Omnitron

Systems Technology, Inc.

Warranty

This product is warranted to the original purchaser

against defects in material and workmanship for a

period of TWO YEARS from the date of shipment. A

LIFETIME warranty may be obtained by the original

purchaser by REGISTERING this product with

Omnitron within 90 days from the date of shipment.

TO REGISTER, COMPLETE AND MAIL OR FAX

THE ENCLOSED REGISTRATION FORM TO THE

INDICATED ADDRESS. Or you may register your

product on the Internet at http://www.omnitron-systems.

com. During the warranty period, Omnitron will, at its

option, repair or replace a product which is proven to

be defective.

For warranty service, the product must be sent to

an Omnitron designated facility, at Buyer’s expense.

Omnitron will pay the shipping charge to return the

product to Buyer’s designated US address using

Omnitron’s standard shipping method.

Limitation of Warranty

The foregoing warranty shall not apply to defects

resulting from improper or inadequate use and/or

maintenance of the equipment by Buyer, Buyer-supplied

equipment, Buyer-supplied interfacing, unauthorized

modications or tampering with equipment (including

removal of equipment cover by personnel not specically

authorized and certied by Omnitron), or misuse, or

operating outside the environmental specication of the

product (including but not limited to voltage, ambient

temperature, radiation, unusual dust, etc.), or improper

site preparation or maintenance.

No other warranty is expressed or implied. Omnitron

specifically disclaims the implied warranties of

merchantability and tness for any particular purpose.

Exclusive Remedies

The remedies provided herein are the Buyer’s sole and

exclusive remedies. Omnitron shall not be liable for any

direct, indirect, special, incidental, or consequential

damages, whether based on contract, tort, or any

TECHNICAL SUPPORT:

For help with this product, contact Omnitron’s Tech.

Support:

Phone: (949) 250-6510

Fax: (949) 250-6514

Address: Omnitron Systems Technology, Inc.

38 Tesla

Irvine, CA 92618 USA

E-mail: support@omnitron-systems.com

URL: http://www.omnitron-systems.com

SPECIFICATIONS (CONT.):

TROUBLESHOOTING GUIDE:

Problem:

The Power LED does not illuminate after installation

is complete.

Possible Causes:

A. Conrm that the power supply is connected.

B. Conrm that the correct power supply is being used.

Problem:

The Fiber Optic link LED does not illuminate after

installation is complete.

Possible Causes:

A. Confirm that the fiber optic cable is properly

connected to the miConverter Gx and the remote ber

optic device.

B. Conrm that the ber cable type matches the ber

transceiver type (multimode, single-mode) on the

miConverter Gx.

C. If using a dual-ber model, conrm that the transmitter

(Tx) is attached to the receiver side of its link partner,

and that the receiver (Rx) is attached to the transmitter.

D. If using a single-ber model, conrm that the Tx

wavelength on the miConverter Gx matches the Rx of

the connected ber optic device.

Problem:

The Fiber Optic link LED blinks slowly after installation

is complete, indicating connected devices are not able

to complete auto-negotiation.

Possible Causes:

A. Conrm that the miConverter Gx and the connected

ber optic and UTP devices are set to auto-negotiation

mode. If the connected ber device does not support

auto-negotiation, congure the miConverter to MAN

mode.

B. Conrm that the UTP cables of the miConverter Gx

and the connected ber optic and UTP devices are

properly connected.

C. If two miConverter Gx converters are connected via

ber, conrm that both converters have their ber optic

ports set to auto-negotiate “AN” and their UTP ports

connected to remote devices.

D. Conrm that the connected UTP and ber optic

devices have the same Duplex/Pause capabilities.

Problem:

The UTP link LED does not illuminate after installation

is complete.

Possible Causes:

A. Conrm that the UTP cable is connected properly

to the miConverter Gx and the attached UTP device.

B. Conrm that the UTP cable pin-out is correct

(EIA/TIA-568-A).

C. Conrm that the attached UTP device is working

properly and is capable of Gigabit Ethernet speed.

Note: If corrective actions do not resolve your

situation, please contact Omnitron Systems

Page 13

Description

1000BASE-T UTP to 1000BASE-X

Copper to Fiber Media Converter

with Auto-negotiation

Protocols

802.3ab, 1000BASE-T,

1000BASE-X

UTP Cable Type

EIA/TIA 568A/B

Category 5 and higher

Fiber Cable Type

Multimode: 50/125,

62.5/125, 100/140um

Single-mode: 9/125um

UTP Connector Type

RJ45

Fiber Connector Types

Single-Fiber: SC

Dual Fiber: ST, SC

Power Requirements

Minimum DC Power 0.5A @ 5VDC

DC Power Connector 2.5mm DC Jack - Center Positive

AC Power Adapter

[US]

100-120VAC/60Hz

0.03A @ 120VAC

AC Power Adapter

[Universal and

Country/Region Specific]

100-240VAC/50-60Hz

0.03A @ 120VAC

Dimension (WxDxH)

W:1.71" x L:4.10" x H:0.84"

Weight

without power adapter

5 oz.

with USB power adapter cable 6 oz.

with AC power adapter [US] 12 oz.

with AC power adapter

[Universal]

19 oz.

Compliance

UL, CE, FCC Class A

Temperature

Operational 0 to +50

Storage -50 to +80

Humidity

(non-condensing)

5% to 95%

Altitude [ft]

-100m to 4000m

MTBF [hrs]

without power adapter 810,000

with US and

Country/Region Specific

power adapter

250,000

with Universal power adapter 100,000

LED INDICATORS:

Function Color Legend Off State On / Blinking State

Power Amber PWR No power Amber = power

F/O link Act Green F/O No fiber

optic link

Green = li nk

Green rapid blink (10Hz) = data

Green slow blink (0.5Hz) = fiber

cable is connected but unable

to complete auto-negotiation

F/O Auto-Neg Green AN Manual

mode

Auto-negotiation mode

UTP-link Act Green UTP No UTP

link

Green = li nk

Green rapid blink (10Hz) = data

Full-Half

Duplex

Green FDX UTP is at

Half-Duplex

UTP is at Full-Duplex

Note: For additional assistance with LED

indicators, please refer to the miConverter Gx

TROUBLESHOOTING GUIDE (pp. 11-13).