Owner's manual

iConverter 4GT
Standalone Module User Manual
Product Overview
The iConverter 4GT standalone module is an unmanaged four-port 10/100/1000Mbps Ethernet
switch that supports Half/Full Duplex and auto-negotiation on each RJ-45 port.
Model Numbers
Model Number Description
8482-4-D Wall mount with External US AC Power Supply
8482-4-E Wall mount with External Universal AC Power Supply
8482-4-F Wall mount with DC Terminal Power
Installation Procedure
1) Congure DIP-switches
2) Install Standalone Module and Connect Cables
3) Verify Operation
1) CONFIGURE DIP-SWITCHES
DIP-switches are located on the side of the module.
DIP-SWITCH BANK 1
The location of the DIP-switches is shown in Figure 1.
Figure1: DIP-switch Locations
Each port can be congured for Auto Negotiation (AN) or Manual conguration (Man). When
congured for AN, the port automatically determines the speed, duplex and pause capability of the
connected device. If the port is congured for Manual, the speed and duplex is determined by the
100/10 and FDX/HDX DIP-switches (see Figure 4 for conguration details).
1000Mbps Manual operation is not supported. For 1000Mbps operation, congure the ports for
AN operation.
The functions of DIP-switch Bank 1 are outlined in Figure 2. DIP-switch Bank 1 controls the
operation of Port 1 and Port 2.
Switch Legend Function
DOWN
(Default)
UP
SW3 AN/Man Port 1 Negotiation AN Man
SW4 100/10 Port 1 Speed 100 10
SW5 FDX/HDX Port 1 Duplex FDX HDX
SW6 AN/Man Port 2 Negotiation AN Man
SW7 100/10 Port 2 Speed 100 10
SW8 FDX/HDX Port 2 Duplex FDX HDX
Figure 2: DIP-switch Bank1 Denitions
SW3 - Port 1 “AN/Man”
This DIP-switch congures Port 1 for Auto Negotiation or Manual operation.
SW4 and SW5 - Port 1 Speed “100/10” and Duplex “FDX/HDX”
See Figure 4 for conguring duplex and speed when the port is congured for Manual operation.
3) VERIFY OPERATION
Verify the correct LED is illuminated based on the conguration of the port.
Figure 6: Front panel layout
Each port can operate at 10/100/1000Mbps. The gure below indicates the operation of the port
based on the illuminated LEDs. If the 100 LED is illuminated, the port is operating at 100Mbps. If
the 1000 LED is illuminated, the port is operating at 1000Mbps and if the 100 and 1000 LEDs are
illuminated, the port is operating at 10Mbps.
LED Function
“Legend”
Color OFF State ON/Blinking State
Power
“PWR”
Green No power Module has power
P1 Link Activity
“100”
Green Port not linked at 100M
ON: Port linked at 100M
Blinking: Data activity
P1 Link Activity
“1000”
Green Port not linked at 1000M
ON: Port linked at 1000M
Blinking: Data activity
P1 Link Activity
“100” and “1000”
Green Port not linked at 10M
ON: Port linked at 10M
Blinking: Data activity
P2 Link Activity
“100”
Green Port not linked at 100M
ON: Port linked at 100M
Blinking: Data activity
P2 Link Activity
“1000”
Green Port not linked at 1000M
ON: Port linked at 1000M
Blinking: Data activity
P2 Link Activity
“100” and “1000”
Green Port not linked at 10M
ON: Port linked at 10M
Blinking: Data activity
P3 Link Activity
“100”
Green Port not linked at 100M
ON: Port linked at 100M
Blinking: Data activity
P3 Link Activity
“1000”
Green Port not linked at 1000M
ON: Port linked at 1000M
Blinking: Data activity
P3 Link Activity
“100” and “1000”
Green Port not linked at 10M
ON: Port linked at 10M
Blinking: Data activity
P4 Link Activity
“100”
Green Port not linked at 100M
ON: Port linked at 100M
Blinking: Data activity
P4 Link Activity
“1000”
Green Port not linked at 1000M
ON: Port linked at 1000M
Blinking: Data activity
P4 Link Activity
“100” and “1000”
Green Port not linked at 10M
ON: Port linked at 10M
Blinking: Data activity
Figure 7: LED Indicators
040-08482-001B 12/10
Page 1
Omnitron Systems Technology * 140 Technology Dr. #500 * Irvine, CA 92618
949.250.6510 tel * 949.250.6514 fax * www.omnitron-systems.com