FlexSwitchTM 4Fx Model 6530-FK Replacement Kit User Manual 140 Technology #500, Irvine, CA 92618 Phone: (949) 250-6510; Fax: (949) 250-6514
Table of Contents 1.0 1.1 1.2 2.0 2.1 2.2 2.3 3.0 3.1 3.2 3.3 3.3.1 3.3.2 4.0 4.1 5.0 6.0 INTRODUCTION .................................................................... 3 General Description ............................................................. 3 Chassis Models .................................................................... 3 INSTALLATION ...................................................................... 4 Chassis Installation ............................................................
1.0 INTRODUCTION 1.1 General Description The 6530-FK is the direct replacement for the discontinued FlexSwitch Model 600XC 4Fx. The 6530-FK replacement kit consists of two iConverter Fast Ethernet Fiber-to-Fiber Media Converter Modules installed in an iConverter 2Module chassis. The 6530-FK provides four 100Base-Fx fiber ports supporting half or full duplex operation. The 6530-FK features front panel accessible DIP-Switches for convenient configuration of the fiber ports.
2.0 INSTALLATION 2.1 Chassis Installation The 6530-FK is designed to accommodate wall-mounting and tabletop installations. For wall-mounting, the 8249-0 Wall-Mount kit (sold separately) is designed to attach the chassis to a wall, backboard or other flat surfaces. For tabletop installations, place the unit on a flat level surface. Attach the rubber feet to the bottom of the chassis to prevent the unit from sliding. Make sure the unit is placed in a safe, dry and secure location.
3.0 CONFIGURATION 3.1 AC Site Preparation • • • • • 3.2 Power source should be available within 5 ft. of the chassis and installed per the National Electrical Code ANSI/NFPA-70. This equipment requires a 100-240VAC, 0.5Amp, 50/60Hz power outlet. Appropriate overloading protection should be provided on the AC power source outlets utilized. The operating temperature of this equipment is 0 to 50 degrees C.
3.3 Configuring the DIP-Switches 3.3.1 Media Converter Modules - Front Panel The Media Converter Modules have been pre-configured for full duplex operation as illustrated below. For half duplex operation, use the front panel DIP-Switch associated with the appropriate fiber port.
the LEFT position, Link Propagate mode is enabled. Note: Setting both the “LP”, “ RFD” and “SFD” to the RIGHT positions on the same module is an illegal mode that will result in unpredictable behavior. Remote Fault Detection “RFD” DIP-Switch When the Remote Fault Detect “RFD” DIP-Switch is in the RIGHT position, the RFD mode is selected. When in the LEFT position (factory default), the RFD mode is disabled. When the “RFD” and the “LP” DIP-Switches are in the RIGHT position, the RFD+LP mode is selected.
5.0 SPECIFICATIONS Description Four Port Fast Ethernet Optical Switch Protocols 100Base-Fx Fiber Cable Type Multimode: 50/125, 62.5/125,100/140um Singlemode: 9/125um Fiber Connector Type ST or SC DIP-Switches Link Modes: LS/LP, RFD, SFD Fiber: FDX/HDX LED Displays Power, Fiber Link, FDX/HDX Power Requirements 100 - 240 VAC @ 0.5A/0.4A, 50/60 Hz Dimensions W: 6.7" x D: 5.51" x H: 1.87" Weight 3.0 lbs.
6.0 LINK MODES In order to accommodate different user requirements, the 6530-FK Media Converter Modules support five different link modes: Link Segment (LS) LS mode transmits a link signal independently of any received Link at any port. Utilizing this configuration, a loss of a receive link signal will only affect the port detecting the loss of signal. All the other ports will continue to generate a link signal. A loss of link on the UTP port, only affects the UTP port; the other ports remain unaffected.
Warning The operating description in this Instruction Manual is for use by qualified personnel only. To avoid electrical shock, do not perform any servicing of this unit other than that contained in the operating instructions, unless you are qualified and certified to do so by Omnitron Systems Technology, Inc. Caution All user-required operations can be performed without opening the unit. Never attempt to open or remove the cover or tamper with the unit.
TECHNICAL SUPPORT If you encounter problems with this product, contact Omnitron Technical Support. Phone: Fax: Address: 800-675-8410 949-250-6510 949-250-6514 Omnitron Systems Technology, Inc. 140 Technology Dr., #500 Irvine, CA 92618 Email: URL: support@omnitron-systems.com http://www.omnitron-systems.
