Installation

INSTALLATION INSTRUCTIONS FOR LATCHSETS
Installing Latch - Skip to #4 Instruction if door is pre-bored.
1. Following template, mark all points for drilling. Use correct
backset for latch. Drill 2 " bore first.
2. Using 1" bit, drill from door edge across the bore to
accommodate latch length.
3. With face cover in place, position latch and mark perimeter
of latch faceplate on door edge. Mortise to accommodate
latch face and face cover, approximately deep (refer to
Figure #1).
5. Position latch [G] in door to suit bevel (refer to Figure #1).
Screw latch [G] to
door.
:
6.
For 2 diameter
roses or narrow plates drill ¾" diameter hole instead of
2 " bore.
BEFORE INSTALLING ROSE
Insert spindle [F] through latch hub. FOR PRIVACY
FUNCTION: Insert split spindle until spindle stop hits
latch hub.
"
"
PASSAGE :
PRIVACY :
4. When installing a passage latch, hold latch
with writing on label facing upwards.
When installing privacy latch, the side of the
privacy that is inside of the room must be towards locking
side of room. (refer to Figure #2 on reverse side).
To change latch bolt bevel, pull latch bolt out slightly and
rotate 180 degrees. faceplate [H] and
Installing Passage and Privacy Rose Set (refer to Figure #4)
1. Place the adaptor [E] and adaptor [J] into the door prep,
on either side of the door. Fasten the adaptors together
using the (2) screws [K] provided by passing them through
the adaptor [J] and into the adaptor [E]. (do not fully
tighten).
Make
sure the spindle [F] is centered in the hole of the adaptors
[E] and [J].
2. Place levers [A] onto each end of spindle [F] and test
operation of latch. If operation is smooth, fully tighten
screws [K] and remove levers [A] and washers [C].
3. Place a finished rose [D] and [L] onto each adaptor. For
privacy function, ensure that the privacy hole is towards the
door edge. Thread washers [C] onto inside and outside
adaptors securing the finished roses [D] and [L]. Use the
washer installation tool [N] to fully tighten each threaded
washer [C].
4. Slide both levers [A] onto the spindle [F] until securely
seated into the threaded washers [C]. (For privacy
function, ensure the spindle [F] is centered in the latch [G]
so that each lever [A] works independently). Insert the set
screws [B] provided into the levers [A] and secure the
levers [A] to the spindle [F]. If installing privacy function,
thread the privacy pin [M] through the rose [L] into the
latch.
Install the nylon threaded washers [C] onto
the adaptors before applying roses [D] and [L].
Your Omnia Dealer/Distributor can help you with any further
questions or information on other Omnia Products.
1
/
8
1
/
8
5
/
32
CEDAR GROVE, NJ 07009
9/26/2012
OM-PDY1
TUBULAR LATCH TEMPLATE
FOLD ALONG DOOR EDGE
DRILL 1" DIA. HOLE
IN DOOR EDGE
1 "
DOOR
3
4
1 "
DOOR
3
8
3
8
38" FROM FLOOR
3
4
2 " BACKSET
2 " BACKSET
11
16
"
7
8
"
5
32
"
FACEPLATE
1 x 2” ”
1
/
4
2 " BORE
1
/
8
NOTE: Template may not be true-to-size. Please use for reference
purposes only. DO NOT drill until measurements are verified.
CAUTION: DOOR AND FRAME MANUFACTURERS
When door gasketing or silencers are used, proper allowances must be made for strike location to
maintain a common centerline with lock and door so that the bolt will freely enter strike
.
3
4
2 " B.S
2 "
3
8
or
NARROWER WIDTH (LOW SIDE)
WIDER WIDTH (HIGH SIDE)
Figure #1
*
* Cut high side of door deeper on the
face to compensate for bevel.
For beveled edged door