Safety & Warranty Warnings OMNE SLEEP READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT If unable to understand warnings, cautions, and/or instructions, contact the dealer or technical personnel if applicable, before attempting to use the equipment. Otherwise, injury or damage may result. SAFETY WARNINGS: Product Rating: The motors are not designed to operate continuously for more than • Do not use bed outdoors.
Parts List OMNE SLEEP All electronics and components that need to be installed are located in boxes under the foundation or attached to the frame. Before discarding the packing materials, ensure that all the parts are accounted for.
0S2 Electronics Quick Reference Guide [os2 WIRELESS OVERVIEW Customer Service: 1-888-236-3044 OMNE SLEEP
OMNE SLEEP 0S25 Electronics Quick Reference Guide OS25 WIRELESS OVERVIEW Customer Service: 1-888-236-3044
0S3 Electronics Quick Reference Guide [OS3 WIRELESS OVERVIEW �l�G l]�(I) El0El @�@ �B§l Customer Service: 1-888-236-3044 OMNE SLEEP
OMNE SLEEP 0S65 Electronics Quick Reference Guide [OS65 WIRELESS OVERVIEW Foot Massage Motor @(i)@ (�Jl:�)I�] Customer Service: 1-888-236-3044
OMNE SLEEP Installation Guide Two people are required to set up the foundation. NOTE: To avoid damage to the foundation, always open the carton while the bed is in the flat position. STEP6 Locate the power supply and install (2) 9-volt batteries (not included). STEP7 1--· Carefully flip the foundation over onto its legs. STEP 1 Important: Two people are required to move the foundation. Do not drag across the floor. Do not rest frame on its side; excessive pressure may damage the legs ..
OMNE SLEEP 0S2/0S25 Remote Control Instructions 2 �-------------------- � ,------Flash Light ��El EJ Head Lifts and Lower� $HEAD Foot Lifts and Lowers $FOOT ... t] .:....I.: The HEAD ..o. • arrows lift and lower the head section of the foundation. The FOOT ..o. • arrows lift and lower the foot section of the foundation. ,,- --' Memory�� Position i \Ill/ ·: One touch flash light on/off. ,,�/ Flat Position Flash Light on/off [cm"E TOUCH BUTTON ;�TJ One touch FLAT preset position [\VI � O
0S3 Remote Control I ntructions OMNE SLEEP Flash Light I Head Lifts and Lowers G --£]
0S65 Remote Control Instructions OMNE SLEEP Flash Light I r+---. t:j GJ. �0UV e:=J 8 �Zero-G Preset Positon TV Preset Positon� Head Lifts and Lowers � ,u:BAR Memory Positions--- --'--� Lounge Preset Positon � Lifts Lowers Lumbar Foot Lifts and Lowers '---------Lowers Lumbar B-Flat Button He�d Ma��age On---[§] � §---Foot Massage on (3 intensities) (3 mtens1t1es) ..,,.
Setting Programmable Positions and Pairing Remote I OMNE SLEEP SETTING PROGRAMMABLE POSITIONS The wireless power bed has a programmable feature that allows you to save custom positions. Please read all the instructions below before setting your custom presets on the remote STEP 1 STEP2 Adjust the head and foot to your desired position. Press and hold the flat button8 first, then press and hold memory button � for 5 seconds until the buttons' lights are flashing. The position is then saved.
Synchronizing Two Bases OMNE SLEEP I SYNCHRONIZING TWO BASES If simultaneous operation of two foundations is desired, please read paring remotes instructions on page 11. STEP 1 STEP 2 Plug A and B bases to power source. Make sure remote A was already paired to Base A and Remote B was paired to Base B. If not, please paring them by following the pairing remote instructions on page 11. STEP 3 Pair remote A to Base B, then base A and base B can be simultaneously operated by Remote A.
OMNE SLEEP Headboard Bracket Installation Guide Headboard brackets are an optional accessory and are not included. A 1/2" (13 mm) socket and 1/2" (13 mm) crescent wrench are necessary to complete installation. L (2) Headboard Brackets __] HEADBOARD BRACKET COMPONENTS (2) T-Brackets (4) Short Bolts (12) Nuts (8) Long Bolts STEP 1 STEP2 The headboard bracket will have 2 long slots to accomodate any frame type. Align the appropiate slots on the bracket with the holes on the bed.
Troubleshooting OMNE SLEEP In the event that the power foundation fails to operate, assess the symptoms and possible solutions provided in the chart below. SYMPTOMS SOLUTIONS Remote control illuminates and appears to be operable, but will not activate bed. Verify that the power cord is plugged into a working, grounded electrical outlet. Test the outlet by plugging in another working appliance.
