OM-CP-RFPULSE2000A Wireless Pulse Data Logger
OM-CP-RFPULSE2000A Product Overview The OM-CP-RFPULSE2000A is a wireless data logger that records pulse output signals from various sensors such as flow meters and anemometers. When started, the data logger samples at 100Hz and at the user specified reading rate. The OM-CP-RFPULSE2000A features a display screen which provides instant access to the current reading, minimum, maximum and average statistics.
Quick Start Manual Quick Start Steps Product Operation (Wireless) 1. Install the Omega Software and USB Drivers onto a Windows PC. 2. The OM-CP-RFC1000-EXT interface device comes with a USB cable. Plug one end of the cable into an available USB port on the PC and plug the opposite end of the cable into the communication port on the OM-CP-RFC1000-EXT. 3. Push and hold the wireless button on the OM-CP-RFPULSE2000A for 5 seconds to activate wireless communication.
OM-CP-RFPULSE2000A Additional Features and Operation Alarm Settings/Rules In the Omega Software, alarms can be created on two levels; in the software itself, and programmed specifically to the data logger. Creating alarm rules in the software allows the user to utilize alarms while real time recording, and have the added benefit of features such as e-mail and SMS notification.
Quick Start Manual Troubleshooting Tips Why is the wireless data logger not appearing in the software? If the OM-CP-RFPULSE2000A doesn’t appear in the Connected Devices panel, or an error message is received while using the OM-CP-RFPULSE2000A, try the following: • Check that the OM-CP-RFC1000-EXT is properly connected. For more information, see Troubleshooting Interface Cable problems (below). • Ensure that the battery is not discharged.
OM-CP-RFPULSE2000A Product Maintenance Battery Replacement Materials: OM-CP-BAT103 1. On the bottom of the enclosure, open the battery compartment by pulling in on the cover tab. 2. Remove the battery by pulling it from the compartment. 3. Install the new battery, taking note of the polarity. 4. Push the cover closed until it clicks.
Quick Start Manual OM-CP-RFPULSE2000A General Specifications Reading Rate 1 reading every second up to 1 reading every 24 hours Memory 16,128 readings • Green LED blinks every 5 seconds to indicate unit is logging LED Functionality • Blue LED blinks every 15 seconds to indicate unit is in wireless mode • Red LED blinks every 1 second to indicate alarm condition Wrap Around Yes Start Modes Immediate Start & Delay Start Battery Type Ultralife 9V lithium battery included; user replaceable Battery Life 5 years
OM-CP-RFPULSE2000A Measurement Sensor Type Channel 1: Ambient; Pulse Detection Circuit Channel 2: Mathematic; Phantom Total Channel Response Time 10uS microseconds Input Range 0 to 4,294,967,295 Pulses Calibrated Accuracy 512 ±1 Pulse Wireless 2.45GHz IEEE 802.15.4 ultra-low power wireless transceiver with fully bi-directional communication ISM band 2.405-2.
Quick Start Manual OM-CP-RFC1000-EXT Wireless Transceiver Other models available: OM-CP-RFC1000-EUR Approved for European markets OM-CP-RFC1000-IP69K Splash Proof for harsh environments
OM-CP-RFC1000-EXT Product Overview The OM-CP-RFC1000-EXT, a high powered transceiver that has a substantially long transmission range, providing enhanced performance in occluded environments (ovens, refrigerators, etc.). The OM-CP-RFC1000EXT also features an external antenna, allowing more flexibility with mounting positions in both orientation and proximity to metal walls. The device may be used as a repeater, or directly plugged into the Windows PC.
Quick Start Manual Mounting Instructions For best wireless performance, both the OM-CP-RFC1000-EXT and the Omega data loggers should be mounted in the same orientation. This usually means that the external antenna should be pointing straight up. The antenna can pivot to accommodate either a wall mount or a desk mount.
OM-CP-RFC1000-EXT Channel Programming The OM-CP-RFC1000-EXT transmits data on the 2.4GHz band and is programmed by default on channel 11. Each Omega Wireless Data Logger and OM-CP-RFC1000-EXT has a set of dip switches with which the channel may be programmed. Different wireless channels may be used to create multiple networks in one area, or to avoid wireless interference from other devices. Any Omega data logger or OM-CP-RFC1000-EXT that is on the same network is required to use the same channel.
Quick Start Manual OM-CP-RFPULSE2000A: To program the channel on the OM-CP-RFPULSE2000A data logger, start by switching the wireless mode to OFF by holding down the Wireless button on the data logger for 5 seconds. 1. 2. 3. 4. Use the USB Cable, plug the USB end of the cable into an available USB port on the PC. Plug the opposite end of the cable into the communication port on the OM-CP-RFPULSE2000A. Open the Omega Software. Locate and select the OM-CP-RFPULSE2000A in the Connect Devices panel.
OM-CP-RFC1000-EXT Troubleshooting Tips Why is the wireless data logger not appearing in the software? If the OM-CP-RFPULSE2000A doesn’t appear in the Connected Devices panel, or an error message is received while using the OM-CP-RFPULSE2000A, try the following: • Check that the OM-CP-RFC1000-EXT is properly connected. For more information, see Troubleshooting Interface Cable problems (below). • Ensure that the battery is not discharged.
Quick Start Manual OM-CP-RFC1000-EXT General Specifications Interface Type Operating Environment LED Indicators Enclosure Materials Dimensions Approvals USB (to PC) / Wireless (to Data Logger) -20°C to +85°C, 0 to 95%RH non-condensing Red & Green ABS Plastic (body), PVC Plastic (antenna) Enclosure: 3.8” x 1.6” x 0.8” / Antenna: 7.2” FCC ID:OA3MRF24J40MC, IC#: 7693A-24J40MC Transmission Distance (To other OM-CPRFC1000-EXTs) 4000’ max. outdoor - line of sight unobstructed 1000’ max.
OM-CP-RFC1000-EXT Compliance Information • “This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
OMEGAnet ® Online Service omega.com Internet e-mail info@omega.com Servicing North America: Servicing Europe: U.S.A.: Omega Engineering, Inc., One Omega Drive, P.O. Box 4047 Benelux: Stamford, CT 06907-0047 Toll-Free: 1-800-826-6342 Tel: (203) 359-1660 FAX: (203) 359-7700 e-mail: info@omega.com Czech Canada: 976 Bergar Laval (Quebec), H7L 5A1 Canada Toll-Free: 1-800-826-6342 TEL: (514) 856-6928 FAX: (514) 856-6886 e-mail: info@omega.
