User manual
3-2 DBK Setup in DaqView 968194 DBK Option Cards and Modules User’s Manual
DBK Reference for DaqView Users
DBK Description Type Comment
DBK33 Triple-Output Power Supply Card Power No configuration in DaqView.
DBK34 Vehicle UPS Module Power No configuration in DaqView.
DBK34A UPS / Battery Module Power No configuration in DaqView.
DBK40 18-Connector BNC Analog Interface Interface No configuration in DaqView.
DBK41 10-Slot Expansion Module Expansion No configuration in DaqView.
DBK42 16-Slot 5B Signal Conditioning Module P1-ANALOG 5B Module selection, see Note 3.
DBK43A 8-Channel Strain-Gage Module P1-ANALOG Must enter J2 setting in H/W Config.
DBK44 2-Channel 5B Signal-Conditioning Card P1-ANALOG 5B Module selection, see Note 3.
DBK45 4-Channel SSH and Low-Pass Filter Card P1-ANALOG Must enter SW6 setting in H/W Config.
DBK46 4-Channel Analog Output Card 4 DAC No configuration in DaqView.
DBK48 16-Slot 8B Signal Conditioning Module P1-ANALOG 8B Module selection, see Note 3.
DBK50 8-Channel High-Voltage Input Module P1-ANALOG Must enter JP1C setting in H/W Config.
DBK51 8-Channel Low-Voltage Input Module P1-ANALOG Must enter JP1C setting in H/W Config.
DBK52 14-Channel Thermocouple Input Module P1-ANALOG
DBK53 16-Ch. Low-Gain Multiplexing Module P1-ANALOG
DBK54 16-Ch. High-Gain Multiplexing Module P1-ANALOG
For these three DBKs: In DaqView’s
Acquisition Setup tab select 100 kHz as
the Internal Clock speed.
DBK55 8-Ch. Frequency to Voltage Input Module P1-ANALOG Must enter S1 setting in H/W Config.
DBK60 3-Slot Expansion Chassis Expansion No configuration in DaqView.
DBK65 8-Ch. Transducer Interface Module P1-ANALOG Must enter S1 setting in H/W Config.
DBK70 Vehicle Network Interface Mux. Module P1-ANALOG Refer to the DBK70 User’s Manual
DBK80
16-Ch. Differential Voltage Input Card with
Excitation Output
P1-ANALOG No configuration in DaqView.
DBK81
7-Channel T/C Card, High-Accuracy
P1-ANALOG
DBK82
14-Channel T/C Card, High-Accuracy
P1-ANALOG
DBK83
14-Ch. T/C Card, High-Accuracy; uses
Connection Pod
P1-ANALOG
DBK84
14-Ch. T/C Module, High-Accuracy
P1-ANALOG
Must select the Thermocouple Type in
DaqView’s Channel Setup Window.
DBK85
16-Ch. Differential Voltage Module
P1-ANALOG No configuration in DaqView.
DBK90
56-Ch. T/C Module, High-Accuracy
P1-ANALOG Must select the Thermocouple Type in
DaqView’s Channel Setup Window.
DBK200 P4-to-P1 Adapter Card Interface No configuration in DaqView.
DBK201 P4-to-P1/P2/P3 Adapter Board Interface No configuration in DaqView.
DBK202 P4-to-P1/P2/P3 Adapter Board, with
Screw Terminals & Locators for RC Filter
Interface No configuration in DaqView.
DBK203 P4-to-P1/P2/P3 Adapter Chassis, with
Screw Terminals & Locators for RC Filter
Interface
No configuration in DaqView.
DBK204 DBK203 with a CA-209 CE Cable Kit
Interface
No configuration in DaqView.
DBK204c DBK203 with a CA-209c CE Cable Kit Interface No configuration in DaqView.
DBK205 P4 to 12-Slot Screw Terminal Adapter Interface No configuration in DaqView.
DBK206 P4-to-P1/P2/P3 Adapter Board,
with Screw Terminals
Interface No configuration in DaqView.
DBK207 16-Channel, 5B Carrier Board P1-ANALOG 5B Module selection, see Note 3.
DBK207/
CJC
DBK207 with Cold Junction Compensation P1-ANALOG 5B Module selection, see Note 3.
Note 3: After selecting the DBK option in the Hardware Configuration window, 5B [or 8B] Module
selection is made in the DaqView main window, on the Channel Setup tab (for Analog and Scanned
Digital Inputs). Clicking on the Units column brings up the 5B [or 8B] Module selection function.