00E Adam .
00E Adam .book Page 2 Tuesday, November 9, 2004 3:24 PM For customers in North and South America For customers in USA Declaration of Conformity Product Name Model Number Trade Name Responsible Party Address Telephone Number :Digital Camera :IR-500 :OLYMPUS : :Two Corporate Center Drive, PO Box 9058, Melville, NY 11747-9058 U.S.A. :1-631-844-5000 Tested To Comply With FCC Standards FOR HOME OR OFFICE USE This device complies with Part 15 of the FCC rules.
00E Adam .book Page 3 Tuesday, November 9, 2004 3:24 PM Introduction Introduction The reference manuals for this camera consist of the following three guides. To ensure correct and safe use of the camera, please read the manuals before using the camera and refer to them whenever necessary during use. Quick Start Guide Contains instructions for basic operations to use the camera immediately after purchase. OK * * Basic Manual Contains instructions for setup and some for basic operations.
00E Adam .book Page 4 Tuesday, November 9, 2004 3:24 PM Introduction • The contents of this manual are subject to change without notice. Contact an authorized Olympus service center in the enclosed Authorized Distributors List with the product name and model number for the latest information. • While every care has been taken in the preparation of this manual, if you find any errors, omissions, or points which are unclear, please contact an authorized Olympus service center.
00E Adam .book Page 5 Tuesday, November 9, 2004 3:24 PM What can I do with the camera? What can I do with the camera? When shooting Retracting display for LCD and lens protection and easy portability Easy self-shooting with the multiswing display (in self-portrait mode g page 61) OPEN Shoot subjects from high or low angles, adjusting the angle of the multi-swing display.
00E Adam .book Page 6 Tuesday, November 9, 2004 3:24 PM How to use this instruction manual How to use this instruction manual How to read the instructions Controls necessary for operations are shown using illustrations. Screens show the results of the operations. This sample page is only for your reference. It may differ from the actual page in this manual. What do the icons mean? This manual uses the following icons: Icons Tip Indicates useful information for convenient camera operation.
00E Adam .book Page 7 Tuesday, November 9, 2004 3:24 PM Table of contents Table of contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 What can I do with the camera? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 How to use this instruction manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
00E Adam .book Page 8 Tuesday, November 9, 2004 3:24 PM Table of contents Chapter 4: Setting according to shooting conditions Zooming in (Telephoto) or out (Wide angle) (W/T) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the flash u ! # $ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Taking close-up pictures (macro/super macro) & % . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the self-timer Y . . .
00E Adam .book Page 9 Tuesday, November 9, 2004 3:24 PM Table of contents Editing still pictures (EDIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recording sound to pictures (postrecording) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Editing movies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Editing movie images (EDIT) . . . . . . . . .
00E Adam .book Page 10 Tuesday, November 9, 2004 3:24 PM Table of contents Setting the operation sound (BEEP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking the picture you have just taken (REC VIEW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting serial numbers for file names (FILE NAME) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjusting the CCD and image processing functions (PIXEL MAPPING) . . . . . . . . .
00E Adam .book Page 11 Tuesday, November 9, 2004 3:24 PM Table of contents Chapter 9: Using images with your computer 202 Before transferring image data to your computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operational sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the supplied OLYMPUS Master software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
00E Adam .book Page 12 Tuesday, November 9, 2004 3:24 PM For safe use of this product Chapter 1: Read this first Chapter 1: Read this first For safe use of this product Be sure to read this section for correct and safe use of the product before you start using the product. Various symbols are used to warn of hazards to yourself and others and prevent damage to property through misuse of the camera. The symbols and their meanings are explained below.
00E Adam .book Page 13 Tuesday, November 9, 2004 3:24 PM For safe use of this product • Avoid prolonged contact with the camera, AC adapter, and cradle while charging. The camera and cradle become hot during charging. Also the camera becomes hot during could result in low temperature burns. • Do not use or store the camera for a long time in an environment where there is a lot of dust, dampness, smoke, or steam. This could result in fire or electric shock.
00E Adam .book Page 14 Tuesday, November 9, 2004 3:24 PM For safe use of this product • Do not leave the camera in places of high temperature. Doing so could result in deterioration of parts or fire. Do not cover the AC adapter or cradle with anything such as a Chapter 1: Read this first cloth or blanket when in use. This may cause overheating, resulting in fire. • Use only the specified AC adapter.
00E Adam .book Page 15 Tuesday, November 9, 2004 3:24 PM For safe use of this product Conditions for use of the product periods of time in the following places as this could result in failure or malfunction.
00E Adam .book Page 16 Tuesday, November 9, 2004 3:24 PM For safe use of this product Precautions regarding the monitor Chapter 1: Read this first • Do not apply excessive pressure to the monitor. This may cause smears, prevent pictures from being played back properly, or damage the monitor. Should the monitor break, avoid getting any of the liquid crystal in your mouth. If it gets on your hands or feet or on your clothing, wash it off immediately with soap and water.
00E Adam .book Page 17 Tuesday, November 9, 2004 3:24 PM For safe use of this product About the AC adapter • Use only the supplied AC adapter. Use the AC adapter within the specified range of voltage. • The AC adapter is for indoor use only. • Be sure to turn off the camera before you disconnect the cables from the terminals or electrical outlet. Failure to do so could affect the camera’s internal image data, settings or functions. • The AC adapter may become warm while being used.
00E Adam .book Page 18 Tuesday, November 9, 2004 3:24 PM For safe use of this product Warning Chapter 1: Read this first • When you store or use the battery, keep the battery out of the reach of children. If the battery is accidentally swallowed, seek medical attention immediately. • Do not wet the battery. Do not immerse the battery in water or in the sea. • Do not expose the battery to strong impacts or damage the battery.
00E Adam .book Page 19 Tuesday, November 9, 2004 3:24 PM For safe use of this product Precautions for handling the picture card • Keep out of the reach of children. Failure to do so may cause accidental swallowing. Caution • The picture card is a precision electronic device. Do not bend it or subject it to impact. And keep it away from static electricity. The data stored on the card is saved in a nonvolatile semiconductor memory, but it can be accidentally destroyed.
00E Adam .book Page 20 Tuesday, November 9, 2004 3:24 PM Unpacking the box contents Unpacking the box contents Chapter 1: Read this first Make sure your box contains everything listed below. If any item is missing or damaged, contact the dealer where you purchased the camera.
00E Adam .book Page 21 Tuesday, November 9, 2004 3:24 PM Names of parts Names of parts The illustrations below show the camera with the multi-swing display turned 360 degrees.
00E Adam .
00E Adam .book Page 23 Tuesday, November 9, 2004 3:24 PM Names of parts Monitor indications A B C D E F G I J K A B +2.0 L M N O P Chapter 1: Read this first Shooting mode Q 4M When shooting still images +2.
00E Adam .book Page 24 Tuesday, November 9, 2004 3:24 PM Names of parts Item Number Indication Chapter 1: Read this first A Battery level e, f P.27 B Shooting mode P, L, K, m, 8, H, y, S, I, o, G, d, J, F, U, e, v, 7, N P.57 P.243 C Camera movement warning a P.52 D Flash standby Flash charging # (Lights) # (Blinks) P.53 P.245 E Green indicator ( P.43 P.245 F Macro mode, Super macro mode &, % P.54 G Flash mode u, !, #, $ (Only $ when shooting movies) P.
00E Adam .book Page 25 Tuesday, November 9, 2004 3:24 PM Names of parts Playback mode You can change the information display to either the standard mode or detail mode. Below are information display mode (INFO)” (g page 110). A B C 10 100 00-0009 10 4M SIZE:2288 1712 +2.0 '04.12.03.14:03 9 When playing back still images A B C E F G H I J K L M N Chapter 1: Read this first the displays when “INFO” is set to “DETAIL” For more information, see “Switching the D 10 100 00-0013 G SIZE:320 240 +2.
00E Adam .book Page 26 Tuesday, November 9, 2004 3:24 PM Names of parts Item Number Indication Chapter 1: Read this first A Battery level e, f P.27 B Playback mode t (Calendar mode) g (Album mode) P.132 P.132 C File number Still image: Movie: D Movie n P.46 E Storage status 2 (When “NOT STORE” is selected/ After the image data is stored to the storage unit) P.129 F Print order × The number of print copies < × 10 P.185 G Protect 9 P.126 H Sound H P.91 P.
00E Adam .book Page 27 Tuesday, November 9, 2004 3:24 PM Names of parts About the battery level You can check the battery level as follows when you turn on the camera or while you are using Lights (green) Pictures can be taken. Blinks (red) The battery is running low. Charge the battery as soon as possible. “BATTERY EMPTY” appears. The battery is empty. Charge the battery. Chapter 1: Read this first the camera. Tip The rate of battery consumption varies greatly depending on the operating conditions.
00E Adam .book Page 28 Tuesday, November 9, 2004 3:24 PM Names of parts About the memory gauge The memory gauge is lit while the still image is being stored onto the card. The indication of the Chapter 1: Read this first memory gauge changes as follows according to the shooting conditions. When the memory gauge is fully lit, wait until the gauge goes off before you resume shooting.
00E Adam .book Page 29 Tuesday, November 9, 2004 3:24 PM Attaching the strap Chapter 2: Preparation NE O OKK Thread the strap through the strap eyelet as shown. SCE V IV ID O OKK Chapter 2: Preparation Attaching the strap Pull the strap tight, making sure that it is securely fastened and does not come loose. Notes • Do not swing the camera around by the strap or pull the strap with excessive force. This may cause the strap to break. • Attach the strap correctly following the steps above.
00E Adam .book Page 30 Tuesday, November 9, 2004 3:24 PM About the battery and card About the battery and card About the battery Chapter 2: Preparation The Olympus LI-12B (supplied) or LI-10B lithium ion battery can be used with this camera. Do not use any other type of battery. The battery is not fully charged when the camera is purchased. Charge the battery using the supplied cradle before using the camera. For details, see “Charging the battery” (g page 33).
00E Adam .book Page 31 Tuesday, November 9, 2004 3:24 PM About the battery and card Inserting the battery and card Open the battery/card cover. Chapter 2: Preparation PUSH PUSH N OPE OK 1 OK EN OP Grasp the cover on both sides and lift it up. 2 Insert the battery and card as shown below. Inserting the battery Inserting the card PUSH PUSH OK OK EN OP EN OP Battery lock lever Press up the battery lock lever with the corner of the battery. Push the card in until it clicks.
00E Adam .book Page 32 Tuesday, November 9, 2004 3:24 PM About the battery and card 3 Close the battery/card cover. OK EN OP Chapter 2: Preparation PUSH Notes • The camera does not work if the battery/card cover is not closed properly. • Do not open the battery/card cover, disconnect the AC adapter, or remove the camera from the cradle while the camera is operating or communicating with a computer. Such actions could destroy all the data on the card. Once destroyed, data cannot be restored.
00E Adam .book Page 33 Tuesday, November 9, 2004 3:24 PM Charging the battery To remove the card Push the card in. The card springs up so you can pull the card out. PUSH OK EN OP OK EN OP Chapter 2: Preparation PUSH Note If you release your finger quickly after pushing the card in or flick the card to remove it, the card may jump out. Remove the card with care. Charging the battery The supplied lithium ion battery (LI-12B) is not fully charged when the camera is purchased.
00E Adam .book Page 34 Tuesday, November 9, 2004 3:24 PM Charging the battery 1 Connect the AC adapter to the cradle. Cradle Chapter 2: Preparation To a wall outlet A / V OUT (MONO) + DC IN 5V USB USB To DC input terminal AC adapter (A511) * The shape of the plug differs from country to country. 2 Power cord* Set the camera on the cradle. The mark on the camera connector dial indicates the orientation of the camera when the camera is set on the cradle.
00E Adam .book Page 35 Tuesday, November 9, 2004 3:24 PM Charging the battery 3 Charging begins. The power lamp slowly blinks during charging. The lamp goes off when charging is complete. Tips • We recommend using an AC adapter for time-consuming tasks such as image downloads to a computer, printing, or slide shows. For information on the supplied AC adapter, be sure to read “About the AC adapter” (g page 17).
00E Adam .book Page 36 Tuesday, November 9, 2004 3:24 PM Power on/off Power on/off Opening the multi-swing display Chapter 2: Preparation The camera automatically turns on when the multi-swing display is opened. The camera turns off when the display is closed. Multi-swing display Pressing the power switch When the camera is off with the multi-swing display opened, press the power switch to turn on the camera. The power lamp lights up. To turn off the camera, press the power switch again.
00E Adam .book Page 37 Tuesday, November 9, 2004 3:24 PM How to use the multi-swing display How to use the multi-swing display You can shoot at various angles by turning the multi-swing display. Determine the desired angle of the multi-swing display while watching the monitor, then take a picture. Chapter 2: Preparation SCENE VIV ID P-AUTO QUICK VIEW OK OPEN Turn the multi-swing display 360 degrees for normal shooting. You can take a photo of yourself while viewing your image on the monitor.
00E Adam .book Page 38 Tuesday, November 9, 2004 3:24 PM Setting the date and time Setting the date and time The date and time are not preset. If you set the date and time, it will be stored with shot images and available for printing images. Chapter 2: Preparation Tip If the date and time are not set, “Y/M/D” appears every time you turn on the camera. 1 Turn the mode dial to q. The setup menu appears.
00E Adam .book Page 39 Tuesday, November 9, 2004 3:24 PM Setting the date and time 3 Select the date format. While “o” is selected, press a/c to select the date format from among “_Y_M_D,” “_M_D_Y,” and “_D_M_Y.” The following steps show the procedure used when the date format is set to “_Y_M_D.” 00 : 00 SELECT 4 SET GO Press d to go to the year field. Press a/c to set the year. After setting the year, press d to go to the month field. Chapter 2: Preparation 2004 . 01 .
00E Adam .book Page 40 Tuesday, November 9, 2004 3:24 PM Setting the date and time 5 Press 9 to confirm the date and time settings. The clock starts at the same time you press 9. Chapter 2: Preparation 40 Note The date and time settings will be canceled if the camera is left with the battery removed for more than one day (under the standard Olympus testing conditions). If this occurs, set the date and time again.
00E Adam .book Page 41 Tuesday, November 9, 2004 3:24 PM Holding the camera correctly Chapter 3: Basic shooting and playback Holding the camera correctly movement while taking a picture. Extending your arms may cause camera movement, which can cause blurred images. Horizontal grip Incorrect grip Be careful to keep your fingers and the strap away from the lens and flash.
00E Adam .book Page 42 Tuesday, November 9, 2004 3:24 PM Easy shooting with P-AUTO (Program Auto) mode Easy shooting with P-AUTO (Program Auto) mode Taking a picture using the P-AUTO (Program Auto) mode is easy because the camera will make the most suitable settings automatically. Chapter 3: Basic shooting and playback Composing the image and taking a shot 1 Turn the mode dial to j.
00E Adam .book Page 43 Tuesday, November 9, 2004 3:24 PM Easy shooting with P-AUTO (Program Auto) mode 3 Press the shutter button gently. This is the half-press position of the shutter button. The green indicator lights up when the focus and exposure are locked. The green indicator blinks if the subject is not in focus. Recompose the picture, and hold down the shutter button until the green indicator lights up. Half-press 4 When the green indicator lights up, press the shutter button all the way.
00E Adam .book Page 44 Tuesday, November 9, 2004 3:24 PM Easy shooting with P-AUTO (Program Auto) mode Subjects that are difficult to focus on using the AF (Auto Focus) This camera’s auto focus feature brings the subject into focus automatically. However, under certain conditions, the auto focus may not function effectively. Try the following methods if the subject is difficult to focus on.
00E Adam .book Page 45 Tuesday, November 9, 2004 3:24 PM Easy shooting with P-AUTO (Program Auto) mode Recomposing the shot after locking the focus (Focus Lock) When the subject you want to focus on is out of the AF target mark (not in the center of the monitor), lock the focus and take the picture as explained below. This is called Focus Lock. 1 Position the AF target mark on the subject you want to focus on.
00E Adam .book Page 46 Tuesday, November 9, 2004 3:24 PM Recording movies Recording movies You can record movies as well as still images with this camera. To record a movie, set the shooting mode to n (movie). View the monitor while shooting. Chapter 3: Basic shooting and playback Tips • The focus and optical zoom are locked while you are shooting a movie with sound. • If you want to record a movie without sound, set “R” to “OFF.” For details, see “Recording sound with movies (R)” (g page 94).
00E Adam .book Page 47 Tuesday, November 9, 2004 3:24 PM Recording movies 2 Press the shutter button halfway (half-press). The green indicator lights up when the focus and exposure are locked. Green indicator (Lights up) 3 Press the shutter button all the way (full-press). The recording starts. The power lamp blinks during recording. Tip During movie recording, the “N” indicator lights in red and the remaining recording time is displayed. 4 Press the shutter button again to stop recording.
00E Adam .book Page 48 Tuesday, November 9, 2004 3:24 PM Viewing/Erasing the shot images Viewing/Erasing the shot images Easy playback with the h button Press h after shooting. POWER The still image or movie you have just taken appears. Chapter 3: Basic shooting and playback 48 QUICK VIEW 100 00-0009 0009 4M SIZE:2288 1712 +2.0 Displays the previous image. h button OK 9 button OPEN OPEN OK Displays the next image. '04.12.03.14:03 '04. 12.03.
00E Adam .book Page 49 Tuesday, November 9, 2004 3:24 PM Viewing/Erasing the shot images Erasing an image using the S button 1 Display the image you want to erase, then press S. POWER The “ERASE” screen appears. 2 abcd buttons QUICK VIEW Press a/c to select “YES.” OPEN S button YES NO SELECT 3 9 button OPEN GO Press 9. The selected image is erased.
00E Adam .book Page 50 Tuesday, November 9, 2004 3:24 PM Zooming in (Telephoto) or out (Wide angle) (W/T) Chapter 4: Setting according to shooting conditions Zooming in (Telephoto) or out (Wide angle) (W/T) Chapter 4: Setting according to shooting conditions This camera has an optical zoom up to 2.8 × (40 to 112 mm (1.6" to 4.4"), 35mm film format equivalent.) Tip With the combined optical and digital zoom functions, images can be zoomed up to an approximate factor of 30.
00E Adam .book Page 51 Tuesday, November 9, 2004 3:24 PM Using the flash u ! # $ Using the flash u ! # $ The camera is initially set to “AUTO” (auto-flash), but you can select from the following five flash modes according to the shooting conditions. AUTO (default setting) The flash fires automatically in low light or backlight conditions. The flash is weakened. This is effective when “AUTO” or “#” (fill-in flash) is too strong and too bright.
00E Adam .book Page 52 Tuesday, November 9, 2004 3:24 PM Using the flash u ! # $ $ (flash off) The flash does not fire even in low-light conditions. Use this flash mode when you do not want to fire the flash even in a dark place. Also use this flash mode when you shoot night or sunset scenes where the flash is not effective. Chapter 4: Setting according to shooting conditions Note Since a slow shutter speed is automatically selected in low light situations, take care to avoid camera shaking.
00E Adam .book Page 53 Tuesday, November 9, 2004 3:24 PM Using the flash u ! # $ 3 Press a/c to select the flash mode, then press 9. Shooting mode resumes with the chosen flash mode. The flash mode indication is displayed on the screen when a flash mode other than “AUTO” is set. Flash standby icon (Lights up when the flash is ready to fire.) Selected flash mode Flash effective range The appropriate shooting distance when using the flash is shown below. Shooting distance [in wide angle (W)]: approx. 0.
00E Adam .book Page 54 Tuesday, November 9, 2004 3:24 PM Taking close-up pictures (macro/super macro) & % Taking close-up pictures (macro/super macro) & % Use the macro mode when you want to shoot close to the subject, for example when taking a picture of a flower. The camera takes longer than usual for focusing when taking close-ups. In such cases, select the macro mode so that you can obtain faster focusing.
00E Adam .book Page 55 Tuesday, November 9, 2004 3:24 PM Using the self-timer Y 3 Press a/c to select the macro setting, then press 9. Shooting mode resumes with the chosen macro mode setting. When macro mode is set, & appears in the monitor. When super macro mode is set, % appears. OFF GO Notes • If you use the flash in & (macro) mode, shadows may be noticeable or the appropriate exposure may not be obtained. • The zoom or flash cannot be used in % (super macro) mode.
00E Adam .book Page 56 Tuesday, November 9, 2004 3:24 PM Using the self-timer Y 3 Press c to select “ON,” then press 9. The self-timer is set and shooting mode resumes. OFF ON SELECT Chapter 4: Setting according to shooting conditions 56 4 GO “Y” appears when self-timer mode is set. Press the shutter button. The picture will be taken approximately 12 seconds after the shutter button is pressed. Tips • The self-timer lamp lights for about 10 seconds after the shutter button is pressed.
00E Adam .book Page 57 Tuesday, November 9, 2004 3:24 PM Selecting a scene mode according to the subject (SCENE SELECT) Selecting a scene mode according to the subject (SCENE SELECT) This camera is preset with 17 types of scene mode selections. Settings such as tone, brightness, and shutter speed are pre-determined for each type of scene, which allows for easy shooting with just one press of the shutter button. 1 Turn the mode dial to l.
00E Adam .book Page 58 Tuesday, November 9, 2004 3:24 PM Selecting a scene mode according to the subject (SCENE SELECT) 3 Press d to enter the scene mode settings, then press a/c to select the scene mode. The sample image of the selected scene mode appears. 17 VIVID 17 VIVID Vividly reproduce colors. Uses different way from program auto. Chapter 4: Setting according to shooting conditions 58 SELECT GO SELECT Selected scene mode 4 GO Then the explanation of the scene mode appears.
00E Adam .book Page 59 Tuesday, November 9, 2004 3:24 PM Selecting a scene mode according to the subject (SCENE SELECT) LANDSCAPE (L) For shooting landscapes. Vivid reproduction of blues and greens. For shooting both main subject and background. Vivid reproduction of blues and greens. NIGHT SCENE (m) (Can also be selected by turning the mode dial to n.) For shooting illuminated scenes in evening or at night. Uses a slower shutter speed than in normal shooting.
00E Adam .book Page 60 Tuesday, November 9, 2004 3:24 PM Selecting a scene mode according to the subject (SCENE SELECT) NIGHT+PORTRAIT (8) For shooting both main subject and illuminated background in evening or at night. Uses a slower shutter speed than in normal shooting. Chapter 4: Setting according to shooting conditions The shutter speed will be slower. Take care to avoid camera shaking. INDOOR (H) For shooting both main subject and background indoors. Background is reproduced clearly.
00E Adam .book Page 61 Tuesday, November 9, 2004 3:24 PM Selecting a scene mode according to the subject (SCENE SELECT) SUNSET (S) For shooting setting/rising sun. Vivid reproduction of reds and yellows. A flash cannot be used. Take care to avoid camera shaking. For taking a portrait-style shot. SELF PORTRAIT (o) (Can also be selected by turning the mode dial to o.) Lets you take a picture of yourself while holding the camera.
00E Adam .book Page 62 Tuesday, November 9, 2004 3:24 PM Selecting a scene mode according to the subject (SCENE SELECT) CUISINE (G) For still life photography. Vividly reproduces colors of fruit, vegetables, flowers, etc. Chapter 4: Setting according to shooting conditions 62 DOCUMENTS (d) For shooting documents, etc. Increases contrast between letters and background. A flash cannot be used. Take care to avoid camera shaking. SPORT (J) Captures fast-moving action without blurring.
00E Adam .book Page 63 Tuesday, November 9, 2004 3:24 PM Selecting a scene mode according to the subject (SCENE SELECT) BEACH & SNOW (F) For shooting snow-capped mountains, landscapes, white sand sea-scapes, etc. For shooting under candlelight. Warm colors are reproduced. A flash cannot be used. Take care to avoid camera shaking. AVAILABLE LIGHT PORTRAIT (e) For shooting sensitive subjects in low light conditions without a flash.
00E Adam .book Page 64 Tuesday, November 9, 2004 3:24 PM Selecting a scene mode according to the subject (SCENE SELECT) BEHIND GLASS (v) For shooting a subject through glass. Chapter 4: Setting according to shooting conditions 64 VIVID (7) (Can also be selected by turning the mode dial to k.) Vividly reproduce colors. Uses different way from PAUTO (Program Auto.
00E Adam .book Page 65 Tuesday, November 9, 2004 3:24 PM Selecting the record mode (D) Selecting the record mode (D) Your choice to store the image to the card in a particular record mode should be determined according to its purpose. (Still image Number of storable images without sound (with a 16 MB card) SUPER HIGH 4M* 2288 × 1712 16 The number of pictures you can take is fewer and it takes time to store images.
00E Adam .book Page 66 Tuesday, November 9, 2004 3:24 PM Selecting the record mode (D) Resolution (image size) This refers to the number of pixels (horizontal × vertical) used when saving an image. If the image will be printed, higher resolutions (larger numbers) are recommended so that the image will be clearer. However, higher resolutions make the file size (amount of data) larger, so the number of pictures that can be saved will be fewer.
00E Adam .book Page 67 Tuesday, November 9, 2004 3:24 PM Selecting the record mode (D) (Movie (maximum continuous recording time) The maximum continuous recording time per movie varies depending on the record mode. Record mode Resolution (image size) (Frames per second) Max. continuous recording time with sound (with a 16 MB card) Max. continuous recording time without sound (with a 16 MB card) 640 × 480 (15 frames/sec.) 17 sec. 17 sec. STANDARD*1 320 × 240 (30 frames/sec.) 34 sec. 35 sec.
00E Adam .book Page 68 Tuesday, November 9, 2004 3:24 PM Selecting the record mode (D) 2 Press p to select the shooting menu, then press a/c to select “D.” Press d to enter the record mode settings, then press a/c to select the record mode. DIGITAL ZOOM WB Chapter 4: Setting according to shooting conditions 68 SUPER HIGH 4M HIGH 2M BASIC 1M E-MAIL VGA The still image shooting menu is displayed. 3 Press 9 to confirm the selected record mode. The selected record mode is set.
00E Adam .book Page 69 Tuesday, November 9, 2004 3:24 PM Sequential shooting (j) Sequential shooting (j) This function allows you to take pictures in rapid succession by keeping the shutter button pressed. (You can shoot approx. 7 frames continuously when the record mode is set to “SUPER HIGH 4M.
00E Adam .book Page 70 Tuesday, November 9, 2004 3:24 PM Sequential shooting (j) 2 Press p to select the shooting menu, then press a/c to select “j.” Press d to enter the sequential shooting mode settings, then press a/c to select “ON.” OFF ON Chapter 4: Setting according to shooting conditions 70 DIGITAL ZOOM WB 3 Press 9. The camera enters the sequential shooting mode. To exit the setting screen and resume shooting mode, press p. “j” appears when the camera enters sequential shooting mode.
00E Adam .book Page 71 Tuesday, November 9, 2004 3:24 PM Adjusting the settings to suit a bright/dark subject (F) Adjusting the settings to suit a bright/dark subject (F) If your subject is extremely bright or dark, or if there is a considerable difference between the brightness of the subject and the brightness of the background, you can adjust the brightness using the exposure compensation feature. You can adjust the brightness between +2.0 and –2.0 in 1/2 steps.
00E Adam .book Page 72 Tuesday, November 9, 2004 3:24 PM Adjusting the settings to suit a bright/dark subject (F) 3 Press d to enter the exposure compensation settings, then press a/ c to select the exposure compensation value. The gauge for adjusting exposure compensation appears on the monitor. Adjusts towards “+” to give a brighter image. 0.0 Chapter 4: Setting according to shooting conditions CANCEL 4 SELECT GO OK Adjusts towards “–” to give a darker image. Press 9.
00E Adam .book Page 73 Tuesday, November 9, 2004 3:24 PM Enabling the digital zoom (DIGITAL ZOOM) Enabling the digital zoom (DIGITAL ZOOM) This camera is equipped with two zooms, a normal zoom (optical zoom) and a digital zoom. The optical zoom is operated simply by turning the zoom lever, but to use the digital zoom, “DIGITAL ZOOM” must be set to “ON.” When using the digital zoom, the picture can be enlarged up to 11 times. 1 Turn the mode dial to j, k, i, n, o, l, or n.
00E Adam .book Page 74 Tuesday, November 9, 2004 3:24 PM Enabling the digital zoom (DIGITAL ZOOM) 2 Press p to display the shooting menu. Press a/c to select “DIGITAL ZOOM.” DIGITAL ZOOM WB Chapter 4: Setting according to shooting conditions 74 SUPER HIGH 4M OFF 0.0 OFF AUTO The still image shooting menu is displayed. 3 Press d to enter the digital zoom settings, then press a/c to select “ON.
00E Adam .book Page 75 Tuesday, November 9, 2004 3:24 PM Enabling the digital zoom (DIGITAL ZOOM) 4 Press 9. The digital zoom function turns on. To exit the setting screen and resume shooting mode, press p. Optical zoom Digital zoom T T 4M Amount of image magnification with the optical zoom lens. When the optical zoom is zoomed to maximum extension, the zoom function will switch to digital zoom. 4M Turn the zoom lever further towards T (U).
00E Adam .book Page 76 Tuesday, November 9, 2004 3:24 PM Selecting the white balance according to the surrounding lighting (WB) 5 31> Selecting the white balance according to the surrounding lighting (WB) 5 3 1 > Different types of light (such as full daylight, sunset/sunrise, and artificial lighting) produce different shades of white when reflected on white paper.
00E Adam .book Page 77 Tuesday, November 9, 2004 3:24 PM Selecting the white balance according to the surrounding lighting (WB) 5 31> 2 Press p to display the shooting menu. Press a/c to select “WB.” DIGITAL ZOOM WB SUPER HIGH 4M OFF 0.0 OFF AUTO 3 Press d to enter the white balance settings, then press a/c to select the white balance. AUTO DIGITAL ZOOM WB 4 Press 9 to confirm the selected white balance. The selected white balance is set. Press p to start shooting with the new settings.
00E Adam .book Page 78 Tuesday, November 9, 2004 3:24 PM Selecting the white balance according to the surrounding lighting (WB) 5 31> Notes on white balance • The white balance feature may not be effective under some special lighting conditions, such as when multiple lights are used. • If you set a white balance mode other than “AUTO,” play back the picture and check the colors on the monitor.
00E Adam .book Page 79 Tuesday, November 9, 2004 3:24 PM When the brightness of the subject and background differ (METERING) 5 When the brightness of the subject and background differ (METERING) 5 Taking backlit pictures may result in darkened foreground objects and faces. Using SPOT metering in such situations will ensure that the subject is clear regardless of the background light.
00E Adam .book Page 80 Tuesday, November 9, 2004 3:24 PM When the brightness of the subject and background differ (METERING) 5 2 Press p to select the shooting menu, then press a/c to select “METERING.” Press d to enter the “METERING” settings, then press a/c to select “SPOT.” METERING AF MODE AUTO SPOT PANORAMA 2 IN 1 Chapter 4: Setting according to shooting conditions 80 3 Press 9. “METERING” is set to “SPOT.” Press p to start shooting with the new settings.
00E Adam .book Page 81 Tuesday, November 9, 2004 3:24 PM Changing the focus range (AF MODE) Changing the focus range (AF MODE) If the subject is out of focus even when you shoot with the auto focus, you can narrow the autofocusing area only to the AF target mark. AUTO The camera always focuses on the AF target mark. When it is difficult to focus on the subject with auto focus, use this mode to lock the focus. Tip “AF MODE” cannot be set in movie shooting mode.
00E Adam .book Page 82 Tuesday, November 9, 2004 3:24 PM Changing the focus range (AF MODE) 2 Press p to select the shooting menu, then press a/c to select “AF MODE.” Press d to enter the “AF MODE” settings, then press a/c to select “SPOT.” METERING AF MODE PANORAMA 2 IN 1 Chapter 4: Setting according to shooting conditions 82 3 AUTO SPOT Press 9. “AF MODE” is set to “SPOT.” Press p to start shooting with the new settings.
00E Adam .book Page 83 Tuesday, November 9, 2004 3:24 PM Panorama shooting (PANORAMA) Panorama shooting (PANORAMA) You can take advantage of the panorama shooting feature with the supplied Olympus xD-Picture Card. Panorama shooting lets you connect pictures with overlapping edges into a single panoramic picture on a computer using the OLYMPUS Master software contained on the supplied CDROM. 1 Turn the mode dial to j, k, i, n, o, or l.
00E Adam .book Page 84 Tuesday, November 9, 2004 3:24 PM Panorama shooting (PANORAMA) 2 Press p to select the shooting menu, then press a/c to select “PANORAMA.” Press d to enter the panorama settings. METERING AF MODE AUTO AUTO PANORAMA 2 IN 1 Chapter 4: Setting according to shooting conditions 84 OFF 3 On the monitor, use the arrow pad to choose the direction you want to take the pictures in. d: Takes pictures from left to right. b: Takes pictures from right to left.
00E Adam .book Page 85 Tuesday, November 9, 2004 3:24 PM Panorama shooting (PANORAMA) 4 Take the first picture. 5 Make sure that the edges of the pictures overlap, then take your pictures. Use the frames at the edges of the screen as a guide when composing your pictures. The first and second shots are taken so that they overlap part A. The second and third pictures are taken so that they overlap part B. Remember the image in the frame so that you can compose the next picture.
00E Adam .book Page 86 Tuesday, November 9, 2004 3:24 PM Panorama shooting (PANORAMA) 6 7 Chapter 4: Setting according to shooting conditions 86 When you have finished taking pictures, press 9 to exit panorama shooting. The composite photograph is created by combining the images on a computer using the OLYMPUS Master software contained on the supplied CD-ROM. Tip Sound cannot be recorded during panorama shooting.
00E Adam .book Page 87 Tuesday, November 9, 2004 3:24 PM Stitching together two images (2 IN 1) Stitching together two images (2 IN 1) This function allows you to position two pictures taken in succession next to each other and store them as a single picture. You can combine two different subjects in one picture. First picture Second picture 1st 2nd Chapter 4: Setting according to shooting conditions 4M 4M Positioned on left. Positioned on right.
00E Adam .book Page 88 Tuesday, November 9, 2004 3:24 PM Stitching together two images (2 IN 1) 2 Press p to select the shooting menu, then press a/c to select “2 IN 1.” Press d to enter the “2 IN 1” settings. METERING AF MODE AUTO AUTO PANORAMA 2 IN 1 Chapter 4: Setting according to shooting conditions 88 OFF 3 Take the first shot using the monitor. 1st 4M Tips To cancel shooting in 2 IN 1 shooting mode, press p. The screen returns to the menu.
00E Adam .book Page 89 Tuesday, November 9, 2004 3:24 PM Stitching together two images (2 IN 1) 4 Take the second shot. The first shot and second shot are combined and stored onto the card as a single picture. After storing is complete, the screen returns to the normal shooting screen. 2nd Tip Sound cannot be recorded during 2 IN 1 mode.
00E Adam .book Page 90 Tuesday, November 9, 2004 3:24 PM Recording sound with still pictures (R) Recording sound with still pictures (R) This function lets you record sound when taking a picture. Recording begins about 0.5 seconds after pressing the shutter button and lasts for about 4 seconds. When this function is enabled, sound is automatically recorded after a picture is taken. This is useful for adding an audio comment to the picture.
00E Adam .book Page 91 Tuesday, November 9, 2004 3:24 PM Recording sound with still pictures (R) 3 Press 9. Recording sound with still pictures is set. To exit the setting screen and resume shooting mode, press p. “R” appears when the recording sound with still pictures is set. 100 00-0009 4M While recording sound “H” appears when a picture with sound is played back. '04.12.03.14:03 '04. 12.03.14:03 9 Tips • The volume of the recorded sound can be adjusted during playback.
00E Adam .book Page 92 Tuesday, November 9, 2004 3:24 PM Compensating for camera movement (IMAGE STABILIZER) Compensating for camera movement (IMAGE STABILIZER) The image stabilizer function reduces blurry images from camera movement. This works by changing the image capturing area on the CCD according to the movement of the subject before recording the image. The picture shot using the image stabilizer function is slightly enlarged.
00E Adam .book Page 93 Tuesday, November 9, 2004 3:24 PM Setting the Auto Focus while shooting movies (FULLTIME AF) Tips • To save the IMAGE STABILIZER setting for the next time you use the camera, set “ALL RESET” to “OFF.” For details, see “Saving the settings (ALL RESET)” (g page 148). • This feature may not compensate for large movement and some other movements of the subject.
00E Adam .book Page 94 Tuesday, November 9, 2004 3:24 PM Recording sound with movies (R) 2 Press p to select the shooting menu, then press a/c to select “FULLTIME AF.” Press d to enter the “FULLTIME AF” settings, then press a/c to select “ON.” FULLTIME AF OFF ON FORMAT Chapter 4: Setting according to shooting conditions 3 Press 9. The FULLTIME AF feature is enabled. Press p to start shooting a movie with the new settings.
00E Adam .book Page 95 Tuesday, November 9, 2004 3:24 PM Recording sound with movies (R) 2 Press p to select the shooting menu, then press a/c to select “R.” Press d to enter the recording sound with movies settings, then press a/c to select “ON.” FULLTIME AF FORMAT Press 9. Recording sound with movies is set. Press p to start shooting a movie with the new settings. 100 00-001 0013 “R” appears when recording sound with movies is set. SIZE:320 240 +2.
00E Adam .book Page 96 Tuesday, November 9, 2004 3:24 PM Playing back still images Chapter 5: Playing/Editing images Playing back still images Still pictures recorded on the card can be played back. 1 Turn the mode dial to q. The last picture taken appears on the POWER monitor. Mode dial Chapter 5: Playing/Editing images QUICK VIEW OK abcd buttons OPEN OPEN 9 button 2 Press b/d to select the picture you want to play back. Displays the previous picture. 100 00-0009 0009 4M SIZE:2288 1712 +2.
00E Adam .book Page 97 Tuesday, November 9, 2004 3:24 PM Playing back movies How to play back the recorded sound When a picture with sound is displayed, the sound is reproduced by pressing 9. Turns up the volume. OK Turns down the volume. Playing back movies This section explains you how to play back recorded movies. 1 Turn the mode dial to q after shooting a movie and the card access lamp goes off. Card access lamp POWER Mode dial QUICK VIEW The last movie taken appears on the monitor.
00E Adam .book Page 98 Tuesday, November 9, 2004 3:24 PM Playing back movies 2 Press b/d to select the movie you want to play back. Displays the previous picture. 100 00-001 0013 SIZE:320 240 +2.0 WB AUTO OK Displays the next picture. '04.12.03.14:50 '04. 12.03.14:50 13 3 Press 9. The movie is played back. Chapter 5: Playing/Editing images How to end a movie during playback 1 Press p to display the playback menu. The movie being played back pauses. Press a/c to select “STOP.
00E Adam .book Page 99 Tuesday, November 9, 2004 3:24 PM Playing back movies Operations while playing back a movie Volume up 100 00-001 0013 SIZE:320 240 +2.0 WB AUTO '04.12.03.14:50 '04. 12.03.14:50 13 Volume down Hold down this button for 2× speed playback. Hold down during 2× speed playback for 20× speed. To return to normal playback, release the button. Pause Press this button for reverse playback. Hold down to fast reverse at 2× speed. Hold down during 2× speed playback for 20× speed.
00E Adam .book Page 100 Tuesday, November 9, 2004 3:24 PM Playing back movies To play back movies frame by frame This function lets you play the movie one frame at a time. 1 Press 9 during movie playback. The movie is paused. 2 Select the desired frame. Displays the top frame. 100 00-001 0013 Chapter 5: Playing/Editing images 100 SIZE:320 240 +2.0 WB AUTO OK '04.12.03.14:50 '04. 12.03.14:50 13 Displays the next frame. Displays the last frame. Displays the previous frame.
00E Adam .book Page 101 Tuesday, November 9, 2004 3:24 PM Enlarging pictures (Close-up playback) Enlarging pictures (Close-up playback) A picture displayed on the monitor can be enlarged up to four times its original size. 1 Select a picture. See “Playing back still images” Zoom lever POWER (g page 96). QUICK VIEW See “Playing back movies” (g page 97). abcd buttons OK OPEN OPEN 2 Turn the zoom lever to T (U). The picture is enlarged to 1.5 times. 1.5 1.
00E Adam .book Page 102 Tuesday, November 9, 2004 3:24 PM Displaying several images at once (Index playback) 3 Press a/b/c/d to scroll the enlarged picture up, left, down, and right (scroll function). If you press 9, the movie is played while the picture is in close-up (only for movies). OK 2.5 .5 Chapter 5: Playing/Editing images Displaying several images at once (Index playback) You can display several pictures at once. This function lets you view several thumbnail pictures on the monitor at once.
00E Adam .book Page 103 Tuesday, November 9, 2004 3:24 PM Displaying several images at once (Index playback) 2 Turn the zoom lever to W (G). The index display (four pictures at once) appears. Select the image you want to play back by pressing a/b/c/d. 30 31 32 33 OK Advances to the next image frame by frame. When you press this button while the lower-right image is selected, the display will advance to the next page. Moves to the upper row.
00E Adam .book Page 104 Tuesday, November 9, 2004 3:24 PM Displaying several images at once (Index playback) To change the number of frames in the index display Turn the zoom lever to W (G) during playback. 4 frames appear in the index display. Zoom lever 30 31 32 33 4 frame index display Chapter 5: Playing/Editing images Each turn of the zoom lever to W (G) increases the number of indexed frames to 9, 16, and 25, in order.
00E Adam .book Page 105 Tuesday, November 9, 2004 3:24 PM Playback of the pictures as a slide show (m) Playback of the pictures as a slide show (m) This function displays the images in order frame by frame. You can select from among the following 9 types of slide show playback effects. NORMAL CHECKERBOARD Pictures on the card are played back one The next picture is displayed with a veil. The frame at a time.
00E Adam .book Page 106 Tuesday, November 9, 2004 3:24 PM Playback of the pictures as a slide show (m) 1 Turn the mode dial to q. POWER Mode dial QUICK VIEW p button OK abcd buttons OPEN OPEN 9 button 2 Chapter 5: Playing/Editing images 106 3 Press p to display the playback menu. Press a/c to select “m.” Press d to enter the slide show settings, then press a/c to select the desired slide show effect.
00E Adam .book Page 107 Tuesday, November 9, 2004 3:24 PM Playback of the pictures as a slide show (m) 4 Press 9. The slide show with the selected effect begins. During playback, if you want to view the previous frame or next frame, press b/d. Displays the previous frame. OK Displays the next frame. 5 Press 9 or p to end the slide show. The screen returns to single frame display. Tips • We recommend that you use the AC adapter when running a slide show for a long period of time.
00E Adam .book Page 108 Tuesday, November 9, 2004 3:24 PM Rotating pictures (y) Rotating pictures (y) Pictures taken when the camera is held vertically are played horizontally. This function lets you rotate images so that they are played back with the correct orientation. You can rotate an image 90 degrees clockwise or counterclockwise. 100-0046 4M Chapter 5: Playing/Editing images , 05.07.10.12:41 46 100-0046 4M Rotated 90 degrees clockwise (+ 90°) ,05.07.10.
00E Adam .book Page 109 Tuesday, November 9, 2004 3:24 PM Rotating pictures (y) 3 Press p to display the playback menu, then press a/c to select “y.” Press d to enter the picture rotation settings, then press a/c to select “+ 90°” or “– 90°.” INFO Chapter 5: Playing/Editing images Notes • Movies cannot be rotated. • Protected images cannot be rotated. Cancel the protection setting before rotating. For details, see “Protecting pictures (0)” (g page 126).
00E Adam .book Page 110 Tuesday, November 9, 2004 3:24 PM Switching the information display mode (INFO) Switching the information display mode (INFO) You can choose how much shooting information is displayed on the monitor. DETAIL 100 00-0009 STANDARD 10 4M SIZE:2288 1712 +2.0 Chapter 5: Playing/Editing images '04.12.03.14:03 '04. 12.03.14:03 9 100 00-0009 NO INFO 10 4M '04.12.03.14:03 '04. 12.03.14:03 9 Tip Information appears for about 3 seconds if you set “INFO” to “DETAIL” or “STANDARD.
00E Adam .book Page 111 Tuesday, November 9, 2004 3:24 PM Switching the information display mode (INFO) 3 Press p to display the playback menu, then press a/c to select “INFO.” Press d to enter the information display settings, then press a/c to select “STANDARD,” “DETAIL,” or “NO INFO.” INFO Press 9. The information in the selected mode appears. Press p to resume playback mode. Tip To save the selected information display mode for the next time you use the camera, set “ALL RESET” to “OFF.
00E Adam .book Page 112 Tuesday, November 9, 2004 3:24 PM Playing back on a TV Playing back on a TV You can play back images on a TV. To play back on a TV, set the camera on the cradle and connect the supplied AV cable to the TV. Connecting to a TV 1 Turn off the camera and TV, then connect the cradle and TV.
00E Adam .book Page 113 Tuesday, November 9, 2004 3:24 PM Choosing a starting frame for movie playback (INDEX PLAY) 3 4 Turn the mode dial to q, then turn on the camera. Turn on the TV and set the TV to the video input to which the cradle is connected. For information on how to set the TV’s video input, refer to your TV’s instruction manual.
00E Adam .book Page 114 Tuesday, November 9, 2004 3:24 PM Choosing a starting frame for movie playback (INDEX PLAY) 2 Play back a movie, or pause the movie. “Playing back movies” (g page 97). 3 4 Press p to display the playback menu, then press a/c to select “INDEX PLAY.” Press d to enter the “INDEX PLAY” settings. The movie being played is displayed in time frames in the index display. Select the desired frame by pressing a/b/c/d.
00E Adam .book Page 115 Tuesday, November 9, 2004 3:24 PM Editing still pictures (EDIT) Editing still pictures (EDIT) This function allows you to edit still pictures, such as changing pictures into monochrome (black and white) or sepia color, or changing the picture size. The edited picture is stored as a new picture separate from the original picture. 1 Turn the mode dial to q. POWER Mode dial QUICK VIEW abcd buttons OPEN OPEN 2 3 9 button Play back the picture you want to edit.
00E Adam .book Page 116 Tuesday, November 9, 2004 3:24 PM Editing still pictures (EDIT) 4 Press d to enter the picture edit settings. Press a/c to select the edit mode from among “BLACK & WHITE,” “SEPIA,” or “Q” (resizing), then press 9. BLACK & WHITE SEPIA EDIT ERASE FORMAT ALBUM ENTRY Chapter 5: Playing/Editing images When “BLACK & WHITE” is selected BLACK & WHITE BLACK & WHITE CANCEL SELECT GO When “SEPIA” is selected Press a/c to select “SEPIA,” then press 9.
00E Adam .book Page 117 Tuesday, November 9, 2004 3:24 PM Editing still pictures (EDIT) When “Q” is selected Press a/c to select “640 × 480” or “320 × 240,” then press 9. Resizing of the picture begins. When the resizing is complete, the resized picture appears. CANCEL SELECT GO Recording sound to pictures (postrecording) You can attach sounds (postrecording) to shot still pictures. You can also erase the sound already recorded and re-record the sound.
00E Adam .book Page 118 Tuesday, November 9, 2004 3:24 PM Editing still pictures (EDIT) 3 Press p to display the playback menu, then press a/c to select “R.” Press d to enter the recording sound settings. INFO START Chapter 5: Playing/Editing images 118 4 Press 9. Sound recording begins. When recording ends, the screen returns to the playback menu. Press p to return to playback mode. 100 00-0009 4M “H” appears when a picture with sound is played back. '04.12.03.14:03 '04. 12.03.
00E Adam .book Page 119 Tuesday, November 9, 2004 3:24 PM Editing movies Editing movies Editing movie images (EDIT) You can edit movie images which have been shot. This function allows you to cut a portion of the movie images and save the cut movie to the card as a new file. You can also overwrite the original movie image. 1 Turn the mode dial to q. POWER p button OK abcd buttons OPEN OPEN 9 button 2 Select a movie image you want to edit. “Playing back movies” (g page 97).
00E Adam .book Page 120 Tuesday, November 9, 2004 3:24 PM Editing movies 5 Select the frame you want as the first frame and press 9. The selected frame is set as the first frame. Jumps to the first frame. OK Displays the next frame. While pressed, the movie is fast-forwarded. Jumps to the last frame. 00:00:00/12:56:34 GO Displays the previous frame. While pressed, the movie is rewound. Chapter 5: Playing/Editing images 6 Select the frame you want as the last frame and press 9.
00E Adam .book Page 121 Tuesday, November 9, 2004 3:24 PM Editing movies 8 Press a/c to select “YES,” “RESET,” or “CANCEL,” then press 9. YES: Records the edited content to the card. When recording ends, the screen returns to the playback screen for the edited movie. RESET: Resets the editing settings. Return to step 5. CANCEL: Cancels the edited contents and returns to the playback menu.
00E Adam .book Page 122 Tuesday, November 9, 2004 3:24 PM Editing movies 3 Press p to display the playback menu. Press a/c to select “CAPTURE.” STANDARD INFO INDEX PLAY EDIT CAPTURE 4 Chapter 5: Playing/Editing images 122 Press d to enter the “CAPTURE” settings. The selected movie image is displayed as a single frame. Select the desired frame by pressing a/b/c/d. Jumps to the first frame. OK 00:00:00/12:56:34 Displays the next frame. While pressed, the movie is fast-forwarded.
00E Adam .book Page 123 Tuesday, November 9, 2004 3:24 PM Editing movies 6 Press a/c to select “YES,” “RESET,” or “CANCEL,” then press 9. YES: Records the captured image onto the card. When recording ends, the still picture you created is played back. RESET: Resets the “CAPTURE” settings. Return to step 4. CANCEL: Cancels the captured image and returns to the playback mode menu. CAPTURE YES RESET CANCEL SELECT GO Creating an index (INDEX) You can create a still picture index from a movie.
00E Adam .book Page 124 Tuesday, November 9, 2004 3:24 PM Editing movies 3 Press p to display the playback menu. Press a/c to select “INDEX.” INDEX OFF ERASE FORMAT ALBUM ENTRY 4 Press d to enter the index creation settings. Chapter 5: Playing/Editing images The selected movie is indexed into 9 frames with the first frame selected. The frame in this position is selected as the first index frame.
00E Adam .book Page 125 Tuesday, November 9, 2004 3:24 PM Editing movies 5 Press 9. The last frame is selected. GO 7:36:23/12:56:34 The frame in this position is selected as the last index frame. To change and set the content of the last index frame, press and hold b to rewind the movie until your desired frame appears. 6 Press 9. Press a/c to select “YES,” “RESET,” or “CANCEL,” then press 9. • YES: Records the set contents to the card. When recording ends, the screen returns to the playback menu.
00E Adam .book Page 126 Tuesday, November 9, 2004 3:24 PM Protecting pictures (0) Protecting pictures (0) You can protect important pictures to avoid accidentally erasing them. Protected pictures cannot be erased by the single-frame/all-frame erase function. 1 Turn the mode dial to q. POWER Mode dial QUICK VIEW p button OK Chapter 5: Playing/Editing images OPEN 9 button 2 3 Play back the picture you want to protect. Press p to display the playback menu, then press a/c to select “0.
00E Adam .book Page 127 Tuesday, November 9, 2004 3:24 PM Erasing pictures (ERASE/ALL ERASE) 5 Press 9. The selected picture is protected and the screen returns to playback mode. “9” appears when the picture is protected. 100 00-0009 4M '04.12.03.14:03 '04. 12.03.14:03 9 Erasing pictures (ERASE/ALL ERASE) Pictures recorded on the card can be erased. You can select either “ERASE” to erase only the selected picture or “ALL ERASE” to erase all the pictures on the card.
00E Adam .book Page 128 Tuesday, November 9, 2004 3:24 PM Erasing pictures (ERASE/ALL ERASE) Erasing one frame/all frames 1 Turn the mode dial to q. POWER Mode dial QUICK VIEW p button OK abcd buttons OPEN OPEN 9 button Chapter 5: Playing/Editing images 2 3 Play back the picture you want to erase. Press p to display the playback menu, then press a/c to select “ERASE.” Press d to enter the erase settings. Press a/c to select “ERASE” or “ALL ERASE,” then press 9.
00E Adam .book Page 129 Tuesday, November 9, 2004 3:24 PM Setting images to store on a QDock&Done-compatible storage unit (STORE) 5 Press 9. When “ERASE” is selected, only the selected picture is erased. When “ALL ERASE” is selected, all the images on the card are erased (except protected images and images registered to albums.
00E Adam .book Page 130 Tuesday, November 9, 2004 3:24 PM Setting images to store on a QDock&Done-compatible storage unit (STORE) 3 Press d to enter the storage settings. 4 Press 9. Press a/c to select “STORE.” The setting of whether or not to store all the pictures on the card onto a Dock&Done-compatible storage unit is set.
00E Adam .book Page 131 Tuesday, November 9, 2004 3:24 PM Displaying pictures in a calendar Chapter 6: Viewing images in a calendar or album Displaying pictures in a calendar This camera allows you to display pictures in a calendar. When still pictures and movies are shot, the camera automatically sets the pictures to calendar according to the shooting date. The calendar can be displayed in three ways: as a one-month display, 12-month display, or multi-year display.
00E Adam .book Page 132 Tuesday, November 9, 2004 3:24 PM Playing back pictures from the calendar display 2 Change the calendar display. Turn the zoom lever to change the calendar display. Turn the zoom lever to W (G).
00E Adam .book Page 133 Tuesday, November 9, 2004 3:24 PM Playing back pictures from the calendar display In the case of one-month calendar display Moves to the preceding day. If the first date of the current month is selected, the preceding month is displayed. Moves to the same day of the preceding week. OK OK Moves to the next day. If the last date of the current month is selected, the next month is displayed. Moves to the same day of the next week.
00E Adam .book Page 134 Tuesday, November 9, 2004 3:24 PM Playing back pictures from the calendar display In the case of multi-year display Moves to the preceding year. OK Moves to the next year.
00E Adam .book Page 135 Tuesday, November 9, 2004 3:24 PM Playing back pictures from the calendar display 2 Press 9 to display the selected picture in a single frame. To return to the calendar display, turn the zoom lever to W (G). 2004 12 5 6 7 1 2 3 8 9 10 11 4 100 00-0004 4M 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 OK '04.12.20.20:00 4 Press 9. Displays the picture of the previous frame.
00E Adam .book Page 136 Tuesday, November 9, 2004 3:24 PM Registering pictures into an album (ALBUM ENTRY) Registering pictures into an album (ALBUM ENTRY) The pictures which you have taken can be grouped and organized into albums on the card. There are 12 albums and each album can store up to 100 pictures. Moreover, using the OLYMPUS Master software contained within the supplied CD-ROM, you can store pictures into the albums on the card from a computer. “Launching OLYMPUS Master” (g page 213).
00E Adam .book Page 137 Tuesday, November 9, 2004 3:24 PM Registering pictures into an album (ALBUM ENTRY) 3 Press b/d to select the album where you want to store the picture. The first frame of the pictures entered in the album is displayed to represent this album. Nothing will be displayed for albums in which no pictures are entered. Album number SEL. ALBUM REGISTERED:10 CANCEL The number of pictures entered in this album GO Press 9.
00E Adam .book Page 138 Tuesday, November 9, 2004 3:24 PM Registering pictures into an album (ALBUM ENTRY) 6 Press 9. Registration of the picture begins. When the picture is registered to the album, the screen returns to normal playback mode. BUSY When “SEL. IMAGE” is selected Chapter 6: Viewing images in a calendar or album 5 Press b/d to select the pictures you want to store into the album, then press 9. The selected picture is shown by “0” (a check mark).
00E Adam .book Page 139 Tuesday, November 9, 2004 3:24 PM Viewing the pictures in the albums 6 7 After selecting all of the pictures you want to store into the album, press p. Press a/c to select “YES,” then press 9. Registration of the pictures begins. When the pictures are registered to the album, the screen returns to normal playback mode. ALBUM ENTRY YES NO GO SELECT Viewing the pictures in the albums This section explains how to play back the pictures stored in the albums.
00E Adam .book Page 140 Tuesday, November 9, 2004 3:24 PM Reordering the pictures in an album (REARRANGE) 3 Press 9. The first picture in the selected album is played back. 10 100 00-0011 Displays the preceding picture in the album. 4M OK Displays the next picture in the album. '04.12.03.14:15 '04. 12.03.14:15 11 Turn the zoom lever to T (U) to enlarge the picture.
00E Adam .book Page 141 Tuesday, November 9, 2004 3:24 PM Reordering the pictures in an album (REARRANGE) 2 Press p to display the album menu. 3 Press d to enter the “REARRANGE” settings. Press a/c to select “REARRANGE.” A Press b/d to select the picture you want to move. REARRANGE Selected picture 56 CANCEL SELECT The frame number of the selected picture GO The selected picture is bordered in red. C Press b/d to select the destination.
00E Adam .book Page 142 Tuesday, November 9, 2004 3:24 PM Releasing pictures from the albums (UNDO ENTRY) Releasing pictures from the albums (UNDO ENTRY) This section explains how to release pictures from the albums. The pictures released from the albums remain on the card. Tip The protected pictures are also released from the album. However, the picture remains on the card. 1 Turn the mode dial to g.
00E Adam .book Page 143 Tuesday, November 9, 2004 3:24 PM Releasing pictures from the albums (UNDO ENTRY) 4 Press d to enter the picture release settings. The picture selection screen appears. Select “THIS IMAGE” or “SEL. IMAGE,” then press 9. UNDO ENTRY THIS IMAGE SEL. IMAGE CANCEL SELECT THIS IMAGE: You can release the currently displayed picture. Go to “When “THIS IMAGE” is selected” (g page 143). SEL. IMAGE: You can release another picture or multiple pictures. Go to “When “SEL.
00E Adam .book Page 144 Tuesday, November 9, 2004 3:24 PM Releasing pictures from the albums (UNDO ENTRY) When “SEL. IMAGE” is selected 5 Press b/d to select a picture you want to release, then press 9. To select other pictures, repeat this step. 10/100 SEL. IMAGE CANCEL The selected picture is shown by “0.” To cancel the picture, press 9 again. , 100-0009 EXIT Chapter 6: Viewing images in a calendar or album 144 SELECT 6 04.12.11.
00E Adam .book Page 145 Tuesday, November 9, 2004 3:24 PM Releasing all the pictures from the selected album (UNDO ALL) Releasing all the pictures from the selected album (UNDO ALL) This section explains how to release all the pictures from the selected album. The pictures released from the album remain on the card. Tip If there are any protected pictures in the album, it is also released from the album. However, the pictures will remain on the card. 1 Turn the mode dial to g.
00E Adam .book Page 146 Tuesday, November 9, 2004 3:24 PM Selecting and erasing a picture from an album (ERASE) 5 Press a/c to select “YES,” then press 9. All the pictures are released from the album. When the process is complete, the screen returns to album playback mode. Selecting and erasing a picture from an album (ERASE) You can erase a picture from a selected album. The picture is erased from the card. 1 Turn the mode dial to g.
00E Adam .book Page 147 Tuesday, November 9, 2004 3:24 PM Selecting and erasing a picture from an album (ERASE) 5 Press a/c to select “YES,” then press 9. The selected picture is erased. Then the screen returns to album playback mode. Tips • You can erase pictures and play slide shows from the album menu. For the features you can perform using the album menu, see “Album menu” in “Menu list” (g page 241). • You cannot perform “ALL ERASE” from the album menu.
00E Adam .book Page 148 Tuesday, November 9, 2004 3:24 PM Saving the settings (ALL RESET) Chapter 7: Customizing your camera Saving the settings (ALL RESET) You can let the camera keep the changed settings even after you turn off the camera. For the settings of the functions this feature is applied to, see “Functions that resume their default settings when “ALL RESET” is set to “ON”” (g page 150). The “ALL RESET” setting applies to all modes except setup mode.
00E Adam .book Page 149 Tuesday, November 9, 2004 3:24 PM Saving the settings (ALL RESET) 3 Press a/c to select “OFF” or “ON,” then press 9. “ALL RESET” is set to “OFF” or “ON,” then the screen returns to the setup menu.
00E Adam .book Page 150 Tuesday, November 9, 2004 3:24 PM Saving the settings (ALL RESET) Functions that resume their default settings when “ALL RESET” is set to “ON” Function Default setting Ref. page FLASH MODE AUTO & (macro)/% (super macro) OFF P.51 P.54 Y (self-timer) OFF P.55 D (record mode) Still picture: SUPER HIGH 4M Movie: STANDARD P.65 j (sequential shooting) OFF P.69 F (exposure compensation) ±0 P.71 DIGITAL ZOOM OFF P.
00E Adam .book Page 151 Tuesday, November 9, 2004 3:24 PM Selecting your language for on-screen display (W) Selecting your language for on-screen display (W) You can select the language in which the menus and error messages are displayed on the monitor. 1 Turn the mode dial to q. The setup menu appears. POWER Mode dial QUICK VIEW OK abcd buttons OPEN OPEN 9 button Press a/c to select “W.” ALL RESET SCREEN SLEEP CUSTOM BUTTON 3 OFF ENGLISH OFF 3MIN Press d to enter the language settings.
00E Adam .book Page 152 Tuesday, November 9, 2004 3:24 PM Changing the startup screen (SCREEN) 4 5 Press a/c to select the desired language. Press 9. The selected language is set and the screen returns to the setup menu. Changing the startup screen (SCREEN) You can change the startup screen which appears on the monitor when the power is turned on. Choose from among the following three types of screens.
00E Adam .book Page 153 Tuesday, November 9, 2004 3:24 PM Changing the sleep timer duration (SLEEP) 2 Press a/c to select “SCREEN.” Press d to enter the startup screen settings. ALL RESET SCREEN SLEEP CUSTOM BUTTON 3 OFF 1 2 CLOCK Press a/c to select the desired startup screen. Select “OFF” if no startup screen is needed. 4 Press 9. The selected startup screen is set and the screen returns to the setup menu.
00E Adam .book Page 154 Tuesday, November 9, 2004 3:24 PM Changing the sleep timer duration (SLEEP) 2 Press a/c to select “SLEEP.” Press d to enter the sleep timer settings. ALL RESET SCREEN SLEEP CUSTOM BUTTON 3 4 30SEC 1MIN 3MIN 5MIN 10MIN Press a/c to select the length of time before the camera enters sleep mode. Press 9. The selected sleep timer duration is set and the screen returns to the setup menu.
00E Adam .book Page 155 Tuesday, November 9, 2004 3:24 PM Setting regularly used functions to the custom button (z CUSTOM BUTTON) Setting regularly used functions to the custom button (z CUSTOM BUTTON) You can select a desired function from among the functions listed below and set it to the custom button. D (record mode) See “Selecting the record mode (D)” (g page 65). j (sequential shooting) See “Sequential shooting (j)” (g page 69).
00E Adam .book Page 156 Tuesday, November 9, 2004 3:24 PM Setting regularly used functions to the custom button (z CUSTOM BUTTON) 1 Turn the mode dial to q. The setup menu appears. POWER Mode dial QUICK VIEW OK abcd buttons OPEN OPEN 9 button 2 Press a/c to select “CUSTOM BUTTON.” Press d to enter the custom button settings. CUSTOM BUTTON Chapter 7: Customizing your camera 156 DIGITAL ZOOM CANCEL 3 4 SELECT GO Press a/c to select the function you want to register to the custom button.
00E Adam .book Page 157 Tuesday, November 9, 2004 3:24 PM Erasing the image data automatically after storing them onto the storage unit (ERASE STORED IMAGE) Using the custom button 1 Turn the mode dial to j, k, i, n, o, l, or n. POWER Mode dial QUICK VIEW OK abcd button OPEN OPEN 9 button 2 3 Press c (z) to display the “CUSTOM BUTTON” screen. Press a/c to select the desired function, then press 9.
00E Adam .book Page 158 Tuesday, November 9, 2004 3:24 PM Erasing the image data automatically after storing them onto the storage unit (ERASE STORED IMAGE) 2 Press a/c to select “ERASE STORED IMAGE.” ERASE STORED IMAGE OFF ON SHUTTER SOUND 1 1 BEEP REC VIEW ON 3 Press d to enter the “ERASE STORED IMAGE” settings. Press a/c to select “ON.” ERASE STORED IMAGE Chapter 7: Customizing your camera 158 OFF ON SHUTTER SOUND BEEP REC VIEW 4 Press 9.
00E Adam .book Page 159 Tuesday, November 9, 2004 3:24 PM Setting the warning sound (8) Setting the warning sound (8) You can adjust the volume of, or turn off, the warning sound. 1 Turn the mode dial to q. The setup menu appears. POWER Mode dial QUICK VIEW OK abcd buttons OPEN OPEN 9 button 2 Press a/c to select “8” (warning sound). 3 Press d to enter the warning sound settings. Press a/c to select “ON.
00E Adam .book Page 160 Tuesday, November 9, 2004 3:24 PM Setting the shutter sound (SHUTTER SOUND) 4 Press d to select the warning sound volume “LOW” or “HIGH.” The warning sound at the selected volume level sounds. 5 Press 9. The volume level is set, and the screen returns to the setup menu. Tip Even when “8” (warning sound) is set to “OFF,” the warning sound still sounds depending on the camera’s condition.
00E Adam .book Page 161 Tuesday, November 9, 2004 3:24 PM Setting the shutter sound (SHUTTER SOUND) 3 Press d to enter the shutter sound settings. SHUTTER SOUND OFF 1 2 CANCEL 4 LOW HIGH SELECT GO Press a/c to select “1” or “2.” The selected shutter sound is reproduced. Tip The shutter sound does not sound when “OFF” is selected. Press d to select the shutter sound volume “LOW” or “HIGH.” The shutter sound at the selected volume level sounds.
00E Adam .book Page 162 Tuesday, November 9, 2004 3:24 PM Setting the operation sound (BEEP) Setting the operation sound (BEEP) You can select from two different sounds when you operate the camera. You can also set the volume of each sound to “HIGH” or “LOW.” To disable the operation sound, select “OFF.” 1 Turn the mode dial to q. The setup menu appears. POWER Mode dial QUICK VIEW OK abcd buttons OPEN OPEN 9 button 2 Chapter 7: Customizing your camera 162 Press a/c to select “BEEP.
00E Adam .book Page 163 Tuesday, November 9, 2004 3:24 PM Checking the picture you have just taken (REC VIEW) 4 Press a/c to select “1” or “2.” The selected operation sound is reproduced. Tip The operation sound does not sound when “OFF” is selected. 5 Press d to select the operation sound volume “LOW” or “HIGH.” The operation sound at the selected volume level sounds. BEEP OFF 1 2 6 SELECT GO Press 9. The selected operation sound and volume level are set, and the screen returns to the setup menu.
00E Adam .book Page 164 Tuesday, November 9, 2004 3:24 PM Setting serial numbers for file names (FILE NAME) 2 Press a/c to select “REC VIEW.” Press d to enter the Rec View settings. ERASE STORED IMAGE SHUTTER SOUND BEEP REC VIEW 3 OFF ON Press a/c to select “ON” or “OFF,” then press 9. Rec View is enabled or disabled and the screen returns to the setup menu. Chapter 7: Customizing your camera Setting serial numbers for file names (FILE NAME) There are two file naming methods, “RESET” or “AUTO.
00E Adam .book Page 165 Tuesday, November 9, 2004 3:24 PM Setting serial numbers for file names (FILE NAME) This function can be set to “RESET” or “AUTO” to determine how to assign file and folder numbers. Select the more convenient setting to transfer images to a computer. RESET: This resets the file and folder numbers each time a picture card is inserted into the camera. The file number returns to “0001” and the folder number returns to “100.
00E Adam .book Page 166 Tuesday, November 9, 2004 3:24 PM Adjusting the CCD and image processing functions (PIXEL MAPPING) 2 Press a/c to select “FILE NAME.” Press d to enter the file name settings. FILE NAME PIXEL MAPPING RESET AUTO VOLUME 3 4 Press a/c to select “AUTO.” Press 9. The file naming method is set to “AUTO” and the screen returns to the setup menu.
00E Adam .book Page 167 Tuesday, November 9, 2004 3:24 PM Adjusting the brightness of the monitor (s) 2 Press a/c to select “PIXEL MAPPING.” Press d to enter Pixel Mapping mode. FILE NAME PIXEL MAPPING START VOLUME 3 Press 9 to begin Pixel Mapping. Pixel Mapping starts. When Pixel Mapping is complete, the screen returns to the setup menu. Adjusting the brightness of the monitor (s) This function lets you adjust the brightness of the monitor. 1 Turn the mode dial to q. The setup menu appears.
00E Adam .book Page 168 Tuesday, November 9, 2004 3:24 PM Setting the playback sound volume (VOLUME) 2 Press a/c to select “s.” FILE NAME RESET PIXEL MAPPING ,04.12.03 10:20 VOLUME 3 Press d to enter the monitor brightness adjustment settings. Brightens OK Chapter 7: Customizing your camera SELECT 4 Darkens GO Press 9. The adjusted monitor brightness is confirmed and the screen returns to the setup menu.
00E Adam .book Page 169 Tuesday, November 9, 2004 3:24 PM Setting the playback sound volume (VOLUME) 2 Press a/c to select “VOLUME.” FILE NAME RESET PIXEL MAPPING ,04.12.03 10:20 VOLUME 3 Press d to enter the playback volume settings. Press a/c to select the volume level. FILE NAME PIXEL MAPPING 4 6: Playback sound is muted. Press 9. The volume level for playback sound is set and the screen returns to the setup menu.
00E Adam .book Page 170 Tuesday, November 9, 2004 3:24 PM Selecting the video signal type (VIDEO OUT) Selecting the video signal type (VIDEO OUT) Select NTSC or PAL according to your TV video signal type. When you use the camera with a TV overseas, set the correct video signal type in accordance with the local system before connecting to the TV. If an incorrect video signal type is set, the output images will not appear properly.
00E Adam .book Page 171 Tuesday, November 9, 2004 3:24 PM Resetting the settings to default (MODE RESET) Resetting the settings to default (MODE RESET) You can reset the settings changed for shooting and playback to default (the settings at the time of purchase). Note If you perform “MODE RESET,” all the settings including the saved settings after setting “ALL RESET” to “OFF” will reset to default. 1 Turn the mode dial to q. The setup menu appears.
00E Adam .book Page 172 Tuesday, November 9, 2004 3:24 PM Formatting a card (FORMAT) Formatting a card (FORMAT) A card can be prepared for optimal storing conditions for this camera by formatting. Cards not supplied with this camera or formatted on a computer or another camera must be formatted with this camera. Notes • All data stored on the card is erased when the card is formatted. • All the images on the card including the images protected or registered to the albums are erased.
00E Adam .book Page 173 Tuesday, November 9, 2004 3:24 PM Formatting a card (FORMAT) 2 Press p. Press a/c to select “FORMAT.” EDIT OFF ERASE FORMAT ALBUM ENTRY The still image playback menu is displayed. 3 Press d to enter the format settings. Press a/c to select “YES.” FORMAT CAUTION ERASING ALL SELECT 4 GO Press 9. The camera starts formatting the card. When formatting is complete, the screen returns to the original mode.
00E Adam .book Page 174 Tuesday, November 9, 2004 3:24 PM Using various clock functions from the clock menu Using various clock functions from the clock menu This camera allows you to set the alarm and to select the style of the clock which is displayed in the monitor. The clock related functions can be set using the clock menu. Tip The date and time can also be set using the clock menu rather than using the setup menu. Display the clock menu referring to the steps below, then select “W.
00E Adam .book Page 175 Tuesday, November 9, 2004 3:24 PM Using various clock functions from the clock menu 2 Press p to display the clock menu, then press a/c to select “CLOCK STYLE.” Press d to enter the “CLOCK STYLE” settings. CLOCK STYLE DESIGNER'S DIGITAL ALARM SET ALARM SOUND 3 4 Press a/c to select “DESIGNER’S” or “DIGITAL.” Press 9. The selected clock style is set. Press p and the clock of the selected style appears.
00E Adam .book Page 176 Tuesday, November 9, 2004 3:24 PM Using various clock functions from the clock menu Setting the alarm (ALARM SET) This function allows you to set the alarm. When the alarm is set, even if the camera’s power is Off, the power will automatically turn on at the time set for the alarm to go off. If you want to cancel the alarm, set the alarm to “OFF.” Tip “ALARM SET” cannot be selected if the date and time are not set. Set the date and time before setting the alarm.
00E Adam .book Page 177 Tuesday, November 9, 2004 3:24 PM Using various clock functions from the clock menu 3 Press d to enter the alarm settings. Press a/c to select “ON,” then press d to set the alarm. ALARM SET OFF ON ONE TIME DAILY CANCEL 4 SELECT GO Press a/c to select “ONE TIME” or “DAILY,” then press 9. When “ONE TIME” is selected, the alarm goes off only once. When “DAILY” is selected, the alarm goes off each time the set time arrives. 5 Set the alarm time. set only the time.
00E Adam .book Page 178 Tuesday, November 9, 2004 3:24 PM Using various clock functions from the clock menu 6 Press 9. The selected alarm is set. Press p to return to clock mode. “%” appears when the alarm is set. Note If you want to let the alarm go off while the camera’s power is on, turn the mode dial to r to enter the clock mode.
00E Adam .book Page 179 Tuesday, November 9, 2004 3:24 PM Using various clock functions from the clock menu Setting the type of alarm sound and sound level (ALARM SOUND) This function allows you to set the type of alarm sound and sound level. You can select from three types of alarm sounds. You can also set the volume of each sound to “LOW,” “MID,” “HIGH,” or “GRADUAL” which increases the volume gradually. 1 Turn the mode dial to r.
00E Adam .book Page 180 Tuesday, November 9, 2004 3:24 PM Using various clock functions from the clock menu 4 Press d to enter the volume level settings. Press a/c to select the desired volume level. ALARM SOUND LOW MID HIGH GRADUAL 1 2 3 CANCEL 5 SELECT GO Press 9. The selected alarm sound and volume level are set. Press p to return to clock mode.
00E Adam .book Page 181 Tuesday, November 9, 2004 3:24 PM Selecting a printing method Chapter 8: Printing images Selecting a printing method Several different printing options are available for printing out pictures taken with this camera. Using a QDock&Done-compatible printer If you connect the camera to a separately sold Dock&Done-compatible storage unit or printer, you can easily save and print images without using a computer.
00E Adam .book Page 182 Tuesday, November 9, 2004 3:24 PM Making print reservations (DPOF) Using the printing service offered by camera shops You can have the images on the card printed at a camera shop. If you make print reservations in advance with the camera, you can get pictures printed according to the print reservation data. See “Making print reservations (DPOF)” (g page 182). Making print reservations (DPOF) You can specify pictures and the number of prints on the card.
00E Adam .book Page 183 Tuesday, November 9, 2004 3:24 PM Making print reservations (DPOF) What is DPOF? DPOF is short for Digital Print Order Format. DPOF is the format used to record information relating to which frames have been selected, how many prints are required, and whether the date and time are to be included. The DPOF print reservation data is stored on the card. Notes • DPOF reservations for 999 frames can be made on one card. • Saving print reservation data may take considerable time.
00E Adam .book Page 184 Tuesday, November 9, 2004 3:24 PM Making print reservations (DPOF) 1 Turn the mode dial to q. POWER Mode dial QUICK VIEW p button OK abcd buttons OPEN OPEN 9 button 2 Press p to display the playback menu, then press a/c to select “<.” Press d to enter the print reservation settings. INFO Chapter 8: Printing images When making single-frame reservations (<) 3 Press a/c to select “<.
00E Adam .book Page 185 Tuesday, November 9, 2004 3:24 PM Making print reservations (DPOF) 4 Press 9. • When entered from single-frame playback A picture appears as a single frame. • When entered from index playback Pictures appear in the index display. Select the picture you want to reserve for printing and press 9. (When the index is displayed in 4 frame partitions, you can obtain the same result by turning the zoom lever to T (U) instead of pressing 9.
00E Adam .book Page 186 Tuesday, November 9, 2004 3:24 PM Making print reservations (DPOF) 7 8 Press 9. Press a/c to select “SET,” then press 9. The selected pictures are reserved for printing and the print reservation data is stored on the card. When making an all-frame reservation (U) 3 Press a/c to select “U.” PRINT ORDER ALBUM CHECK / CANCEL CANCEL Chapter 8: Printing images 4 SELECT GO Press 9. Press a/c to select “NO,” “DATE” or “TIME.
00E Adam .book Page 187 Tuesday, November 9, 2004 3:24 PM Making print reservations (DPOF) Making print reservations from an album (ALBUM) This function allows you to select an album and make print reservations. There are two methods of reservation: single-frame reservation (<)—single frames can be selected from an album; and, all-frame reservation (U)—all pictures in an album can be selected. 1 Turn the mode dial to g.
00E Adam .book Page 188 Tuesday, November 9, 2004 3:24 PM Making print reservations (DPOF) 4 Press d to enter the print reservation settings. Press a/c to select “ALBUM.” PRINT ORDER ALBUM CHECK / CANCEL CANCEL SELECT GO Tips • When you enter the print reservation settings from the playback menu, “ALBUM” is not displayed. When you want to make an album reservation, select a picture in the album, press p, then select “<.” • To return to the album selection screen, press p or b.
00E Adam .book Page 189 Tuesday, November 9, 2004 3:24 PM Making print reservations (DPOF) 7 Press a/c to select “< or “U” then press 9. • When “<” (single-frame reservation) is selected Print reservations are made for the selected pictures only. To make single-frame reservations, follow the procedure in “When making single-frame reservations (<)” (g page 184) from step 5. • When “U” (all-frame reservation) is selected Print reservations are made for all the pictures in the selected album.
00E Adam .book Page 190 Tuesday, November 9, 2004 3:24 PM Making print reservations (DPOF) 3 Press d to enter the print reservation settings. Press a/c to select “CHECK / CANCEL.” PRINT ORDER ALBUM CHECK / CANCEL CANCEL SELECT GO Tip When print reservation settings are selected from the album menu, “CHECK / CANCEL” cannot be selected. Perform print reservation settings from the playback menu. 4 Press 9. Chapter 8: Printing images CHECK / CANCEL 100-0041 [DATE] , 04.12.06.
00E Adam .book Page 191 Tuesday, November 9, 2004 3:24 PM Making print reservations (DPOF) 6 Press 9. • When “CANCEL” is selected The print reservation for the selected picture is canceled. If pictures with print reservations are still remaining, the screen will return to step 4. To quit, select “EXIT” and press 9. • When “CANCEL ALL” is selected The print reservations of all the images on the card are canceled. The screen returns to the menu.
00E Adam .book Page 192 Tuesday, November 9, 2004 3:24 PM Printing with a PictBridge-compatible printer 4 Press 9. A picture with a print reservation appears. Press b/d to display the picture you want to check. CHECK / CANCEL “<” and a number of prints appear on a picture with a print reservation. 100-0041 [DATE] , 04.12.06.16:31 IMAGE 5 SELECT CANCEL CANCEL ALL EXIT GO When you finish checking, press a/c to select “EXIT,” then press 9. The screen returns to playback mode.
00E Adam .book Page 193 Tuesday, November 9, 2004 3:24 PM Printing with a PictBridge-compatible printer Standard settings All printers that support PictBridge have standard print settings. By selecting “STANDARD” (g page 199) on the settings screens, images are printed according to these settings. Refer to the instruction manual of your printer for its standard settings or inquire with the printer’s manufacturer. Tip For details of printing paper types, ink cassettes, etc.
00E Adam .book Page 194 Tuesday, November 9, 2004 3:24 PM Printing with a PictBridge-compatible printer 2 Connect the AC adapter to the cradle. Cradle To a wall outlet A / V OUT (MONO) + DC IN 5V USB USB To DC input terminal AC adapter (A511) Power cord* * The shape of the plug differs from country to country.
00E Adam .book Page 195 Tuesday, November 9, 2004 3:24 PM Printing with a PictBridge-compatible printer 3 Connect the supplied USB cable to the cradle’s USB terminal, then set the camera on the cradle with the multi-swing display opened. Camera connector dial A / V OUT (MONO) Turn the dial to select this mark. + DC IN 5V USB OK The camera turns on and the “PC / PRINTER” screen appears. 4 Press a/c to select “SEL. PRINT,” then press 9. printing” (g page 196). PC / PRINTER PC PRINT SEL.
00E Adam .book Page 196 Tuesday, November 9, 2004 3:24 PM Printing with a PictBridge-compatible printer Procedures for printing After you connect the camera to the printer correctly, you can make print reservations for the images to be printed or print pictures one by one by letting the camera display the picture. Check the camera’s monitor while following this procedure. Press a/b/c/d to select a setting item. Select “ALL IMAGES.
00E Adam .book Page 197 Tuesday, November 9, 2004 3:24 PM Printing with a PictBridge-compatible printer c Select the frame(s) you want to print. Display the picture you want to print. You can print the currently displayed picture or make print reservation(s). See “Printing/Making print reservations” (g page 199). 100-0009 PRINT MORE SELECT SINGLE PRINT d Choose the number of prints and print information. PRINT INFO DATE FILE NAME 1 WITHOUT WITHOUT GO e Print.
00E Adam .book Page 198 Tuesday, November 9, 2004 3:24 PM Printing with a PictBridge-compatible printer When you want to select the pictures you want to print from the albums You can select and print pictures from the selected album. You can also print all the pictures in the album. PRINT MODE SELECT ALL IMAGES ALBUM SELECT a Select “ALBUM” and press 9, then the album selection screen appears. GO SEL. ALBUM b Select the images you want to print from the album, then press 9.
00E Adam .book Page 199 Tuesday, November 9, 2004 3:24 PM Printing with a PictBridge-compatible printer b Choosing the paper size and layout The available options vary depending on your printer. If your printer only has its standard settings available, you cannot change the printer’s settings. PRINTPAPER SIZE SIZE BORDERLESS STANDARD CANCEL PRINTPAPER SELECT STANDARD PICS/SHEET STANDARD GO CANCEL SELECT 16 GO SIZE: Choose the paper size from among the options offered by your printer.
00E Adam .book Page 200 Tuesday, November 9, 2004 3:24 PM Printing with a PictBridge-compatible printer d Choosing the number of prints and print information You can specify the number of prints and whether or not to print each picture’s information such as the date and file name. PRINT INFO DATE FILE NAME 1 WITHOUT WITHOUT SELECT < ×: Sets the number of prints. DATE: Prints the date recorded with each picture at the same time.
00E Adam .book Page 201 Tuesday, November 9, 2004 3:24 PM Printing with a PictBridge-compatible printer Exiting direct printing When printing is finished, the monitor returns to the “PRINT MODE SELECT” screen. 1 Press b while “PRINT MODE SELECT” is displayed. PRINT MODE SELECT PRINT ALL PRINT MULTI PRINT ALL INDEX EXIT 2 SELECT GO Press a/c to select “EXIT” in the “PC / PRINTER” screen. PC / PRINTER GO SELECT 3 Disconnect the USB cable from the cradle. The camera turns off.
00E Adam .book Page 202 Tuesday, November 9, 2004 3:24 PM Before transferring image data to your computer Chapter 9: Using images with your computer Before transferring image data to your computer Once the shot images are on your computer, you can do much more than print the pictures you like. Using application software, you can catalog images by date and on your purposes, and edit and process images. Further out, you can send images as attachment to your email through internet.
00E Adam .book Page 203 Tuesday, November 9, 2004 3:24 PM Before transferring image data to your computer Notes • When you connect the camera to your computer with the cradle, use the AC adapter whenever possible. When using the battery, be sure that the battery has sufficient power. Note that the camera's battery will continuously discharge (use energy) when connected (communicating) with a computer.
00E Adam .book Page 204 Tuesday, November 9, 2004 3:24 PM Using the supplied OLYMPUS Master software Using the supplied OLYMPUS Master software The supplied CD-ROM includes the OLYMPUS Master application software for image editing and organizing your photos and movies. What is OLYMPUS Master? OLYMPUS Master is for use on computers to view, edit, and organize the pictures taken with the digital camera. When this software is installed, the following operations can be performed.
00E Adam .book Page 205 Tuesday, November 9, 2004 3:24 PM Using the supplied OLYMPUS Master software Installing OLYMPUS Master Check the operating system of your computer before installing OLYMPUS Master. For the compatibility of a new operating system, see the Olympus website.
00E Adam .book Page 206 Tuesday, November 9, 2004 3:24 PM Using the supplied OLYMPUS Master software Macintosh Chapter 9: Using images with your computer 206 Operating System Mac OS X v10.
00E Adam .book Page 207 Tuesday, November 9, 2004 3:24 PM Using the supplied OLYMPUS Master software Windows 1 Insert the CD-ROM into the CD-ROM drive. The OLYMPUS Master installation window is displayed. If the installation window does not display automatically, double click the [My Computer] icon on your desktop and then click the CD-ROM icon. 2 Select the language to be installed. 3 Click [OLYMPUS Master]. The QuickTime installation window automatically appears.
00E Adam .book Page 208 Tuesday, November 9, 2004 3:24 PM Using the supplied OLYMPUS Master software 5 Operate according to the window messages. When the software license agreement window is displayed, review the agreement and click [Yes]. When the user information window is displayed, type in [Name] and [OLYMPUS Master Serial Number]. Then, select your resident country and click [Next]. The serial number is shown on the label pasted on the CD-ROM package.
00E Adam .book Page 209 Tuesday, November 9, 2004 3:24 PM Using the supplied OLYMPUS Master software 7 Operate according to the window messages. The installation completion window appears. 8 Click [Finish]. The display returns to the initial window. 9 Select the option to restart the computer immediately and click [Finish]. Remove the CD-ROM from the CD-ROM drive and store it. Macintosh 1 Insert the CD-ROM into the CD-ROM drive. The CD-ROM’s window appears. of the CD-ROM on the desktop.
00E Adam .book Page 210 Tuesday, November 9, 2004 3:24 PM Connecting the camera to your computer Connecting the camera to your computer Connect the cradle and your computer using the supplied USB cable, and then set the camera on the cradle. 1 Connect the supplied USB cable to the USB port of your computer. For the location of the USB port on your computer, see the manual for the computer. Look this mark as an indication to connect to the USB port.
00E Adam .book Page 211 Tuesday, November 9, 2004 3:24 PM Connecting the camera to your computer 3 Set the camera on the cradle with the multi-swing display opened. Camera connector dial Turn the dial to select this mark. OK 4 When the “PC / PRINTER” screen appears on the camera’s monitor, select “PC,” then press 9. If the screen disappears, turn off the camera and turn it on again, or remove the camera from the cradle and repeat from step 2.
00E Adam .book Page 212 Tuesday, November 9, 2004 3:24 PM Connecting the camera to your computer 5 The computer recognizes the camera as a new device. • Windows 98SE/Me/2000 The first time when the camera is connected to your computer, the computer automatically installs the software to recognize the camera. Wait until recognition is completed and the completion message is displayed. Click [OK] to complete the message. The computer recognizes the camera as a (removable disk.
00E Adam .book Page 213 Tuesday, November 9, 2004 3:24 PM Launching OLYMPUS Master Launching OLYMPUS Master Windows 1 Double click the (OLYMPUS Master) icon on the desktop. The main menu window appears automatically. Macintosh 1 Double click the (OLYMPUS Master) icon in the [OLYMPUS Master] folder. The main menu window appears automatically.
00E Adam .book Page 214 Tuesday, November 9, 2004 3:24 PM Launching OLYMPUS Master OLYMPUS Master main menu A B D C F E G Chapter 9: Using images with your computer 214 A [Transfer Images] button Use to transfer images from the camera (Olympus model only) or media. B [Upgrade] button Use to display the dialog box for upgrading to OLYMPUS Master Plus. C [Browse Images] button Use to display the browse image. Closing OLYMPUS Master Click the (close) button on the main menu.
00E Adam .book Page 215 Tuesday, November 9, 2004 3:24 PM Displaying camera images on computer Displaying camera images on computer Transferring and storing the camera images on a computer Storing camera images on a computer. 1 In the OLYMPUS Master main menu, click the button. (Transfer Images) The transferring source selection window appears. 2 Click the (From Camera) button in the menu window. The transferring source window appears.
00E Adam .book Page 216 Tuesday, November 9, 2004 3:24 PM Displaying camera images on computer 4 Click the [Browse images now] button. The image transferred into the browse window is displayed. To return to the main menu, click [Menu] in the browse window. Note Never open the battery/card cover or disconnect/connect the AC adapter while the card access lamp is blinking. There is a possibility that the data could be corrupted.
00E Adam .book Page 217 Tuesday, November 9, 2004 3:24 PM Displaying camera images on computer For Windows Me/2000/XP A Click the [Eject Hardware] icon displayed on the control strip. B Click the displayed message. C When the [Safe to Remove Hardware] message is displayed, click [OK]. For Macintosh A Drag and drop the [NO_NAME] (or [Untitled]) icon on the desktop to [TRASH]. 3 Disconnect the USB cable from the cradle.
00E Adam .book Page 218 Tuesday, November 9, 2004 3:24 PM Viewing still images/movies Viewing still images/movies 1 In the OLYMPUS Master main menu, click the button. The Browse Window is displayed. 2 Double click the thumbnail of the still picture you want to view. Thumbnail The display switches to view mode and the picture is enlarged. Chapter 9: Using images with your computer 218 To return to the main menu, click [Menu] in the browse window.
00E Adam .book Page 219 Tuesday, November 9, 2004 3:24 PM Viewing still images/movies Viewing movies 1 In the Browse Window, double click the thumbnail of the movie you want to view. The display switches to view mode and the first frame of the movie is displayed. 2 Click the playback button the movie.
00E Adam .book Page 220 Tuesday, November 9, 2004 3:24 PM Printing images Printing images There are many printing menus for the photos, indexes, postcards, calendars, etc. This section describes how to print photos. 1 In the OLYMPUS Master main menu, click the [Print Images] button. The Print Menu window is displayed. 2 Click the (Photo) button. The photo print window is displayed. 3 Chapter 9: Using images with your computer 220 Click [Settings] on the Photo Print window.
00E Adam .book Page 221 Tuesday, November 9, 2004 3:24 PM Printing images 5 Select the thumbnail of the picture you want to print and click [Add]. The selected picture is displayed on the layout as a preview. 6 Set the number of prints. 7 Click [Print]. Chapter 9: Using images with your computer To return to the main menu, click [Menu] in the photo print window.
00E Adam .book Page 222 Tuesday, November 9, 2004 3:24 PM Transferring and storing camera images to a computer without using OLYMPUS Master Transferring and storing camera images to a computer without using OLYMPUS Master This camera is supported by USB Mass Storage Class Device Standards. Therefore, you can transfer and store images by connecting the camera to a computer with the supplied USB cable without using OLYMPUS Master.
00E Adam .book Page 223 Tuesday, November 9, 2004 3:24 PM Error message list Chapter 10: Others Error message list Error message NO CARD Corrective action Insert a card. Or remove the card and reinsert it correctly (g page 31). Wipe the gold contacts with a commercially available cleaning paper and insert the card again. If the problem persists, format the card (g page 172). If the card cannot be formatted, use another card. There is a problem with the card and it cannot be used.
00E Adam .book Page 224 Tuesday, November 9, 2004 3:24 PM Error message list Error message Corrective action Replace the card or erase unwanted pictures. Transfer the important images to your computer before erasing the image data on the card. CARD FULL The card contains no pictures. Record pictures before playing back. NO PICTURE Use image processing software to view the pictures on a computer. If that cannot be done, the image file is damaged.
00E Adam .book Page 225 Tuesday, November 9, 2004 3:24 PM Error message list Error message Corrective action Close the battery/card cover (g page 32). CARD-COVER OPEN Set the date/time (g page 38). Y/M/D The battery is empty. Charge the battery by setting the camera on the cradle or replace the battery with a fully charged battery. BATTERY EMPTY NOT FOR SHOOTING Chapter 10: Others The camera cannot be used for shooting when set on the cradle. Remove the camera from the cradle.
00E Adam .book Page 226 Tuesday, November 9, 2004 3:24 PM Error message list Error message Corrective action The camera is not connected to the printer or computer correctly. Disconnect the camera and connect it again correctly. NO CONNECTION CANCEL YES There is no paper in the printer. Load some paper in the printer. NO PAPER CANCEL YES The printer has run out of ink. Replace the ink cartridge in the printer. NO INK Chapter 10: Others CANCEL The paper is jammed in the printer.
00E Adam .book Page 227 Tuesday, November 9, 2004 3:24 PM Error message list Error message Corrective action The printer’s paper tray has been removed or a similar action has been taken. Do not operate the printer while configuring the printer settings. SETTINGS CHANGED CANCEL There is a problem with the printer. Turn off the camera and printer, check the printer, and then turn on both devices. PRINT ERROR CANCEL There is a problem with the printer. Press 9 again to restart printing.
00E Adam .book Page 228 Tuesday, November 9, 2004 3:24 PM If a problem arises If a problem arises Possible cause Corrective action Ref. page ( The camera does not operate./The camera's buttons do not operate. The power is off. Chapter 10: Others 228 The camera automatically turns off if you leave the camera for some time. Turn on the camera by opening the multi-swing display or pressing the power switch. P.36 The battery is running low. Charge the battery. P.
00E Adam .book Page 229 Tuesday, November 9, 2004 3:24 PM If a problem arises Possible cause The card is full. Corrective action Erase unnecessary images or replace the card with a new one. If you do not want to erase any image, transfer the images on the card to your computer before erasing the image data on the card. Ref. page P.127 P.215 The battery has run out during shooting or storing image data on the card (the monitor has turned off after “BATTERY EMPTY” was displayed).
00E Adam .book Page 230 Tuesday, November 9, 2004 3:24 PM If a problem arises Corrective action Ref. page If you want the flash to fire every time you shoot, set “FLASH MODE” to “#” (fill-in flash). P.51 The flash cannot be used while the mode dial is set to n. Set the mode dial to j, k, i, n, o, or l. — The battery was not fully charged. Charge the battery until the power lamp goes off. P.33 The camera is used in a cold place. The battery runs out fast at cold temperatures.
00E Adam .book Page 231 Tuesday, November 9, 2004 3:24 PM If a problem arises Corrective action Ref. page Block the sunlight with something such as your hand. — Possible cause The monitor is exposed to direct sunlight. ( The date recorded in the image data is wrong. The date and time are not set. The camera has been left with the battery removed. Set the date and time with the “W” (date and time) settings of the setup menu or clock menu. The date and time are not set at the time of purchase.
00E Adam .book Page 232 Tuesday, November 9, 2004 3:24 PM If a problem arises Possible cause Corrective action Ref. page The camera is in shooting mode. Set the mode dial to q. P.96 The brightness of the monitor is not adjusted properly. Adjust the monitor’s brightness with the “s” (monitor brightness adjustment) settings of the setup menu. P.167 The camera is connected to a TV. If the AV cable is connected to the camera through the cradle, the monitor does not turn on.
00E Adam .book Page 233 Tuesday, November 9, 2004 3:24 PM If a problem arises Possible cause Corrective action Ref. page The subject was out of the working range of the flash. Shoot within the flash working range. “FLASH MODE” was set to “$”(flash off). Set “FLASH MODE” to other than “$” (flash off). P.51 A small subject was shot with the backlit condition. Set “FLASH MODE” to “#” (fill-in flash mode) or set “METERING” to “SPOT” before shooting. P.51 P.
00E Adam .book Page 234 Tuesday, November 9, 2004 3:24 PM If a problem arises Possible cause Corrective action Ref. page ( The image not focused on is played back. The subject that are difficult to focus on was shot. Use focus lock to obtain an accurate focus. P.45 “FLASH MODE” is set to “$” (flash off) in insufficient light condition (camera movement occurred). Set “FLASH MODE” to other than “$.” The shutter speed is slow when you shoot in flash- off mode.
00E Adam .book Page 235 Tuesday, November 9, 2004 3:24 PM If a problem arises When connected to a computer or printer Corrective action Ref. page The USB driver has not been installed. It is necessary to install the USB driver for Windows 98/98SE. P.222 The camera’s power is off. Open the multi-swing display or press the power switch to turn on the camera. P.36 The camera is not set to connect with the computer. Select “PC” in the “PC / PRINTER” screen. P.
00E Adam .book Page 236 Tuesday, November 9, 2004 3:24 PM Menu list Menu list Shooting menu (still image) Item Y Settings Y Chapter 10: Others SCENE SELECT LANDSCAPE/LANDSCAPE+PORTRAIT/ NIGHT SCENE/NIGHT+PORTRAIT/ INDOOR/FIREWORKS/SUNSET/PORTRAIT/SELF PORTRAIT/CUISINE/DOCUMENTS/SPORT/ BEACH & SNOW/CANDLE/AVAILABLE LIGHT PORTRAIT/BEHIND GLASS/VIVID P.57 D (record mode) SUPER HIGH 4M/HIGH 2M/BASIC 1M/ E-MAIL VGA P.65 j (sequential shooting) OFF/ON P.69 F (exposure compensation) –2.0 - 0.0 - +2.
00E Adam .book Page 237 Tuesday, November 9, 2004 3:24 PM Menu list Shooting menu (movie) Item Y Settings Y Ref. page D (record mode) FINE/STANDARD/EXTENDED/SUPER FINE CLIP P.67 IMAGE STABILIZER OFF/ON P.92 F (exposure compensation) P.71 DIGITAL ZOOM OFF/ON P.73 WB (White Balance) AUTO/5/3/1/> P.76 FULLTIME AF OFF/ON P.93 R (recording sound with movies) OFF/ON P.94 FORMAT YES/NO P.172 The items in boldface type are default settings.
00E Adam .book Page 238 Tuesday, November 9, 2004 3:24 PM Menu list Playback menu (still image) Item Y INFO Settings Y NO INFO/STANDARD/DETAIL P.110 m (slide show) NORMAL/SCROLL/FADER/ZOOM DOWN/ZOOM UP/ CHECKERBOARD/BLINDS/SWIVEL/RANDOM P.105 y (image rotation) + 90° / 0° / – 90° P.108 < (print order) Chapter 10: Others 238 Ref. page P.182 R (recording) START P.117 EDIT BLACK & WHITE SEPIA Q (resize): 640 × 480 / 320 × 240 / CANCEL P.115 0 (protect) OFF/ON P.
00E Adam .book Page 239 Tuesday, November 9, 2004 3:24 PM Menu list Playback menu (movie) Item Y Settings Y Ref. page INFO NO INFO/STANDARD/DETAIL P.110 m (slide show) NORMAL/SCROLL/FADER/ZOOM DOWN/ZOOM UP/ CHECKERBOARD/BLINDS/SWIVEL/RANDOM P.105 STOP P.98 INDEX PLAY P.113 EDIT P.119 CAPTURE P.121 INDEX P.123 0 (protect) OFF/ON P.126 ERASE ERASE (one movie erase): YES/NO ALL ERASE: YES/NO P.127 YES/NO P.172 ALBUM ENTRY YES/NO P.136 STORE STORE/NOT STORE P.
00E Adam .book Page 240 Tuesday, November 9, 2004 3:24 PM Menu list Setup menu Item Y Settings Y Ref. page ALL RESET OFF/ON P.148 W (language) ENGLISH/ FRANCAIS/ ESPAÑOL/ PORTUGUES (Settings differ according to the region where the camera is sold.) P.151 SCREEN (startup screen) OFF/1/2/CLOCK P.152 SLEEP 30SEC/1MIN/3MIN/5MIN/10MIN P.153 CUSTOM BUTTON D (record mode) / j (sequential shooting) / P.
00E Adam .book Page 241 Tuesday, November 9, 2004 3:24 PM Menu list Album menu Item Y Settings Y SEL. ALBUM INFO NO INFO/STANDARD m (slide show) NORMAL/SCROLL/FADER/ ZOOM DOWN/ZOOM UP/ CHECKERBOARD/BLINDS/ SWIVEL/RANDOM Still image Movie Ref. page 0 0 P.139 0 0 P.110 P.105 0 0 STOP — 0 P.98 INDEX PLAY — 0 P.113 < (print order) 0 — P.182 REARRANGE 0 0 P.140 UNDO ENTRY 0 0 P.142 YES/NO 0 0 P.145 ERASE ERASE: YES/NO 0 0 P.
00E Adam .book Page 242 Tuesday, November 9, 2004 3:24 PM Menu list Calendar menu Item Y Settings Y Ref. page INFO NO INFO/STANDARD P.110 m (slide show) NORMAL/SCROLL/FADER/ZOOM DOWN/ZOOM UP/ CHECKERBOARD/BLINDS/SWIVEL/RANDOM P.105 STOP P.98 INDEX PLAY P.113 0 (protect) OFF/ON P.126 ERASE ERASE: YES/NO ALL ERASE: YES/NO P.127 FORMAT YES/NO P.172 The items in boldface type are default settings. Clock menu Chapter 10: Others Items Y Settings Y CLOCK STYLE DESIGNER’S/DIGITAL P.
00E Adam .book Page 243 Tuesday, November 9, 2004 3:24 PM List of functions by shooting mode List of functions by shooting mode Some settings may not be available depending on the shooting mode. For details, refer to the table below.
00E Adam .
00E Adam .book Page 245 Tuesday, November 9, 2004 3:24 PM Green indicator/flash mark/flash standby indication Green indicator/flash mark/flash standby indication The green indicator and flash mark appearing on the monitor indicate the following depending on whether they are on, off, or blinking. Indication Green indicator Camera status Possible/Impossible action Lights steadily The subject is in focus (when the shutter button is pressed halfway.) Pictures can be taken.
00E Adam .book Page 246 Tuesday, November 9, 2004 3:24 PM Camera maintenance Camera maintenance Cleaning the camera Exterior Wipe gently with a soft cloth. If the camera is very dirty, soak the cloth in mild soapy water and wring well. Wipe the camera with the damp cloth and then dry it with a dry cloth. If you used the camera at the beach, clean it with a cloth that has been soaked in clean water and well wrung. Lens Blow dust off the lens with a commercially available hand blower.
00E Adam .book Page 247 Tuesday, November 9, 2004 3:24 PM Camera maintenance Storing the camera • If you do not intend to use the camera for a long time, remove the card and battery, and store the camera in a cool, dry, well-ventilated place. • You are recommended to occasionally load the battery and operate the camera to keep it in working order. Condensation inside the camera What is condensation? When it is cold outside, the water vapor in the air is rapidly cooled and turns to droplets of water.
00E Adam .book Page 248 Tuesday, November 9, 2004 3:24 PM Camera specifications Camera specifications Product type Digital camera (for shooting and displaying) Recording system Still image Digital recording (in accordance with DCF) Compatible standards Exif 2.
00E Adam .book Page 249 Tuesday, November 9, 2004 3:24 PM Camera specifications Number of effective pixels 4,000,000 pixels Image pickup device 1/2.7" CCD (primary color filter) Lens Olympus lens 6.2 to 17.3 mm (equivalent to 40 to 112 mm lens on a 35mm film format), F2.9 to 4.8 Photometric system Digital ESP metering by image pickup device, Spot metering system Shutter speed 1/2 to 1/1000 sec. (max. 4 sec. in night scene mode) Shutter shooting distance 0.5 m - ) (1.6 ft. - )) (normal), 0.
00E Adam .book Page 250 Tuesday, November 9, 2004 3:24 PM Camera specifications Specifications of accessories xD-Picture Card Product type xD-Picture Card for digital cameras Memory type NAND flash EEP-ROM Memory capacity 16 MB Operating voltage 3 V (3.3 V) Operating temperature 0 to 55 °C (32 to 131 °F) (operation) / – 20 to 65 °C (– 4 to 149 °F) (storage) Operating humidity Less than 95 % (operation and storage) Dimensions Approx. 20 × 25 × 1.7 mm (0.8" × 1.0" × 0.
00E Adam .book Page 251 Tuesday, November 9, 2004 3:24 PM Camera specifications Lithium ion rechargeable battery (LI-12B) Product type Rechargeable lithium ion battery Nominal voltage DC 3.7 V Nominal capacity 1230 mAh Number of chargings Approx. 300 (Varies according to conditions of use.) Operating temperature 0 to 40 °C (32 to 104 °F) (charge) / – 10 to 60 °C (14 to 140 °F) (operation) / 0 to 30 °C (32 to 86 °F) (storage) Dimensions Approx. 31.9 × 45.8 × 10 mm (1.3" × 1.8" × 0.
00E Adam .book Page 252 Tuesday, November 9, 2004 3:24 PM Glossary Glossary Number of Pixels Pixels are the smallest units which comprise a digital image. Images consisting of greater numbers of pixels are more suitable for creating larger images. Resolution (Image size) This is the size of an image expressed by the number of points (pixels) comprising the image.
00E Adam .book Page 253 Tuesday, November 9, 2004 3:24 PM Glossary DCF (Design rule for Camera File system) The standards for camera file systems stipulated by the Japan Electronics and Information Technology Industries Association (JEITA). DPOF (Digital Print Order Format) This is a format for storing automatic print out information for digital cameras. Which images and the number of copies you want to print can be specified and stored onto the card where the image has been stored.
00E Adam .book Page 254 Tuesday, November 9, 2004 3:24 PM Index Index Chapter 10: Others 254 h button . . . . . . . . . . . . . . . . . . . . . . . 22, 48 12-month calendar display. . . . . . . . . . . . . . 133 2 IN 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 BEHIND GLASS . . . . . . . . . . . . . . . . . . . . . 64 BLACK & WHITE . . . . . . . . . . . . . . . . . . . 116 BLINDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 A C A/V output terminal . . . . . . . .
00E Adam .book Page 255 Tuesday, November 9, 2004 3:24 PM Index DIGITAL ZOOM . . . . . . . . . . . . . . . . . . . . . 73 Dock&Done connector . . . . . . . . . . . . . . . . . 22 DOCUMENTS . . . . . . . . . . . . . . . . . . . . . . . 62 DPOF . . . . . . . . . . . . . . . . . . . . . . . . . . 182, 253 E EDIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Editing movies . . . . . . . . . . . . . . . . . . . . . . . 119 E-MAIL VGA . . . . . . . . . . . . . . . . . . . . 65, 248 ERASE. . .
00E Adam .book Page 256 Tuesday, November 9, 2004 3:24 PM Index METERING. . . . . . . . . . . . . . . . . . . . . . . . . . 79 Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Mode dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 MODE RESET . . . . . . . . . . . . . . . . . . . . . . 171 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . 22, 23 Monitor brightness adjustment . . . . . . . . . . 167 Movies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
00E Adam .book Page 257 Tuesday, November 9, 2004 3:24 PM Index T Tungsten . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 U UNDO ALL . . . . . . . . . . . . . . . . . . . . . . . . . 145 UNDO ENTRY . . . . . . . . . . . . . . . . . . . . . . 142 USB cable . . . . . . . . . . . . . . . . . . . . . . 195, 210 USB terminal . . . . . . . . . . . . . . . . . 22, 195, 210 V VIDEO OUT . . . . . . . . . . . . . . . . . . . . . . . . 170 VIVID . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
00E Adam .book Page 258 Tuesday, November 9, 2004 3:24 PM Before you contact us Before you contact us • Confirm the following points before contacting us so that we can provide quick and accurate answers. • Please fill out this check sheet if you want to contact us by fax or mail. • Symptom, displayed messages, frequency, and other details of the problem: PC-related problems are difficult to accurately identify. Please provide as much detail as possible.
00E Adam .book Page 259 Tuesday, November 9, 2004 3:24 PM http://www.olympus.com/ Shinjuku Monolith, 3-1 Nishi-Shinjuku 2-chome, Shinjuku-ku, Tokyo, Japan Two Corporate Center Drive, PO Box 9058, Melville, NY 11747-9058, U.S.A. Tel. 631-844-5000 Technical Support (USA) 24/7 online automated help: http://www.olympusamerica.com/support Phone customer support: Tel. 1-888-553-4448 (Toll-free) Our phone customer support is available from 8 am to 10 pm (Monday to Friday) ET E-Mail: distec@olympus.
