Axis/Anvil System Installation Guide TOOLS REQUIRED: Powered screwdriver, soft rubber hammer. eg Inset L g Axis Le eg Anvil L myolgoffice.
ANVIL DESK Installation Guide
ANVIL DESK Installation Guide * To prevent possible scratches or damage, assemble the Desk upside down on a soft surface such as a blanket, carpet or packaging. Recommended 2-person Step * Attach Leg to the Top assembly by using Bolts, spring washer, flat washer. Tighten using the Allen Wrench provided. Desk Top Desk Top Desk Back Rail Leg Frame Self-tapping Screw Screw 5mm STEP 1: Loosely assemble frames & rails together (1 turn from tight).
ANVIL DESK (WITH MODESTY) Installation Guide STEP 3: Position the modesty behind the rail. STEP5: Using two people, carefully set the Desk upright and position. STEP 4: Pre-drill holes into the modesty and fully tighten the modesty to the rail with provided screws.
ANVIL DESK Installation Guide * To prevent possible scratches or damage, assemble the Desk upside down on a soft surface such as a blanket, carpet or packaging. Recommended 2-person Step * Attach Leg to the Top assembly by using Bolts, spring washer, flat washer. Tighten using the Allen Wrench provided. Desk Top Desk Side Rail Screw 5mm STEP 1: Assemble frames & rails together, loosely (1 turn from tight). STEP 2: Fix desk top with 5mm overhang over metal frame.
ANVIL DESK (WITH MODESTY) Installation Guide 200mm 200mm STEP 3: Measure 200mm from the front edge. STEP 4: Pre-drill holes into the modesty and the worksurface, fully tighten with provided screws. STEP5: Using two people, carefully set the Desk upright and position.
Anvil Straightline Desk Installation Guide TOOLS REQUIRED: Powered screwdriver myolgoffice.
ANVIL STRAIGHTLINE DESK Installation Guide * To prevent possible scratches or damage, assemble the Desk upside down on a soft surface such as a blanket, carpet or packaging. Recommended 2-person Step * Attach Leg to the Top assembly by using Bolts, spring washer, flat washer. Tighten using the Allen Wrench provided. STEP 1: Assemble frames & rails together, loosely (1 turn from tight). STEP 2: Assemble screen brackets to frame, loosely (1 turn from tight).
ANVIL STRAIGHTLINE DESK Installation Guide Desk Top Screw 5mm Desk Side Rail STEP 3: Fix desk top with 5mm overhang over metal frame. Where desktops butt together, make sure these are fitted tight together. STEP 2: STEP 5: Attach centre screen end seal and top cap with soft non-marking mallet. STEP 6: Attach screens to centre pole with top slug connectors. Fix desk top with 5mm overhang over metal frame. Lastly, fully tighten all rail to frame screws.
ANVIL STRAIGHTLINE DESK Installation Guide Place light mark on desktop. STEP 7: Mark out end of return screens on desk. STEP 9: Remove return screen end seal, and attach screen to bracket with self tapper screws. STEP 8: Remove return screen and fix bracket in place. As an alternative to screws, use 3M double sided tape to fasten return screen bracket to desk top. STEP 10: Attach return screen end seal and top cap with soft non-marking mallet.
ANVIL STRAIGHTLINE DESK Installation Guide STEP 11: Install all top caps simultaneously down all together gently tapping with a soft non-marking mallet. STEP 12: If for whatever reason you have to remove the top seal, then to refit, slightly arc in the middle, placing the 2 ends into location, & gently tap down. STEP 13: Fit power/data rails with screws into frame rail. STEP 14: Fully tighten all rail to frame screws, & then screen bracket screws.
ANVIL STRAIGHTLINE DESK Installation Guide STEP 15: Attach cable trays with screws provided.
Anvil System Straightline with Comseal Brushes Installation Guide TOOLS REQUIRED: Powered screwdriver. myolgoffice.
Anvil System Straightline with Comseal Brushes INSTALLATION GUIDE myolgoffice.
Anvil System Straightline with Comseal Brushes INSTALLATION GUIDE 01 02 Assemble frames & rails together, loosely (1 turn from tight). 03 Assemble screen brackets to frame, loosely (1 turn from tight). 04 Desk Top Screw 5mm Desk Side Rail Fix desk top with 5mm overhang over metal frame. Where desktops butt together, make sure these are fitted tight together. Screw fix the Comseal cable brushes to the base screen.
Anvil System Straightline with Comseal Brushes INSTALLATION GUIDE 05 Slide centre screen pole over bracket. Carefully remove end seal on centre screens & fit screen between end brackets & screw self tappers to fix screen tightly. 07 06 Attach centre screen end seal and top cap with soft non-marking mallet. 08 Place light mark on desktop. Attach screens to centre pole with top slug connectors. Mark out end of return screens on desk. myolgoffice.
Anvil System Straightline with Comseal Brushes INSTALLATION GUIDE 09 Remove return screen and fix bracket in place. As an alternative to screws, use 3M double sided tape to fasten return screen bracket to desk top. 11 Attach return screen end seal and top cap with soft non-marking mallet. 10 Remove return screen end seal, and attach screen to bracket with self tapper screws. 12 Install all top caps simultaneously down all together gently tapping with a soft nonmarking mallet. myolgoffice.
Anvil System Straightline with Comseal Brushes INSTALLATION GUIDE 13 If for whatever reason you have to remove the top seal, then to refit, slightly arc in the middle, placing the 2 ends into location, & gently tap down. 15 Fully tighten all rail to frame screws, & then screen bracket screws. 14 Fit power/data rails with screws into frame rail. 16 Attach cable trays with screws provided. myolgoffice.
Anvil System Straightline with Comseal Brushes INSTALLATION GUIDE myolgoffice.
