Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
IV - 15
Section 4 - Chapter 3 - TCP/IP Configuration and Printing
OKI OkiLAN 6020e User’s Guide
TCP/IP
Configuring for TCP/IP Network
Printing
Most computers that support TCP/IP network printing
use the Remote Line Printer Daemon (LPD) protocol.
This protocol was originally part of the Berkeley
Software Distribution (BSD) version of the UNIX
operating system. Remote LPD was quickly adopted as
a de facto standard. As a result, Remote LPD is now
supported by most versions of the UNIX operating
system and by many TCP/IP packages available for
other operating systems. Configuration of Remote LPD
printing varies among vendors who supply TCP/IP.
You may also use the File Transfer Protocol (FTP) for
printing. Typically FTP is used to transfer files between
computers on a TCP/IP network. The OkiLAN 6020e
simply prints the files it receives from FTP.
Remote Print Queue Name
The Remote Print Queue Name determines which
printer port will service the print job. The Remote Print
Queue Name may also be used to specify ASCII print
jobs. Both Remote LPD and FTP have provisions for
specifying a Remote Print Queue Name.
The OkiLAN 6020e looks at the last character of the
Remote Print Queue Name to determine which printer
port will service the print job. All Remote Print Queue
Names should end with the number 1, 2, 3 or 4. If a
number is not specified, the OkiLAN 6020e will use
printer port 1.
The OkiLAN 6020e is designed to handle many
different types of printers and print data. Typically you
will select the printer type for your printer in telnet
under the Configure Port option. However, if you are
connecting to an ASCII printer, you may wish to use
the OkiLAN 6020e to format the print data for your
printer.