Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
IV - 8
Section 4 - Chapter 2 - Configuring the OkiLAN 6020e
OKI OkiLAN 6020e User’s Guide
Configuring the OkiLAN 6020e
There are four utilities available to configure the
OkiLAN 6020e for TCP/IP printing. You may use
whichever utility is best suited for your needs.
• OkiNet for TCP/IP - Windows TCP/IP print
manager utility. See Chapter 3 of this section for
more information.
• OkiLAN 6020e Configuration Utility - This utility is
accessed via telnet. See Chapter 6 of this section for
more information.
In order to configure the OkiLAN 6020e via telnet,
you must first assign an IP address to the OkiLAN
6020e and verify communication by pinging the
device.
• OkiNet for NetWare - This windows utility must be
run from a Novell NetWare client. See Section III of
this manual for specific information.
• OkiNet for VINES (VPMAN) Utility - This
Windows utility must be run from a Banyan VINES
client (may apply to other OkiLAN print server
models).
Assigning the IP Address
There are eight different methods for assigning an IP
address to the OkiLAN 6020e: Gleaning, Static Route
Entry, DHCP, RARP, BOOTP and using the OkiNet or
OkiNet for VINES utilities. Gleaning, Static Route
Entry and RARP require the OkiLAN 6020e and the
host to be on the same subnet. DHCP and BOOTP also
have this restriction unless the network routers are
configured to pass these requests. The OkiNet and
OkiNet for VINES utilities (may apply to other
OkiLAN print server models) do not have this
restriction.