Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
III - 5
Section 3 - Chapter 1 - Introduction
OKI OkiLAN 6020e User’s Guide
NetWare
Selecting PServer or
RPrinter/NPrinter Mode
Your OkiLAN 6020e supports both PServer and
NPrinter mode. There are several factors to consider
when choosing which mode to use.
In PServer mode, the OkiLAN 6020e operates as the
print server. It services specified queues on the
network. In RPrinter mode, the NetWare Print Server
NLM or EXE is in control.
Feature PServer Mode RPrinter/NPrinter Mode
User
Connection
Requires one NetWare
user connection per
OkiLAN 6020e.
Requires no user
connection.
Performance High performance. Good performance.
Installation Easier to set up.
Requires fewer steps.
More steps to set up, but
works well with existing
utilities.
Print Server Separate print server
node, print server
functions, and NetWare
print server software
not required.
Requires NetWare print
server software. Integrates
with NetWare print utilities.
Status
Reporting
Printer status is
reported via messages
sent to client nodes. Job
status is available via
job notification. Printer
status available via
OkiNet utilities.
Printer status is reported via
PCONSOLE, PSC, and
print server screen. Job
status is reported via the
print server screen, PSC,
job notification.
Security Without supervisor
intervention, other
printers cannot access
data sent to the queues.
Data can be password
protected from the file
server to the printer.
Data can be password
protected from the file
server to the printer.