Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
Index - 2
Index
OKI OkiLAN 6020e User’s Guide
Diagnostic Information
displaying in NetWare,
III-17
DLC/802.2 Protocol Stack,
VI-4
E
Enabling/Disabling Protocols
OkiNet for NetWare, III-17
OkiNet for TCP/IP, IV-32
Error Messages
EtherTalk, VII-11 to VII-12
TCP/IP hardware, IV-53
EtherTalk
OkiLAN 6020e utility
advanced configuration
options, VII-6
enable port option, VII-7
error messages, VII-11 to
VII-12
finding the OkiLAN
6020e, VII-4
printing a configuration
sheet, VII-6
renaming the OkiLAN
6020e printer, VII-5
reset board option, VII-7
restore defaults, VII-7
running, VII-4
selecting a zone, VII-5
set type option, VII-6
status option, VII-6
selecting your printer,
VII-13 to VII-14
F
FCC Statement, 2
Federal Communications
Commission Statement, 2
FTP Printing
ASCII, IV-20
BINARY, IV-20
BYE, IV-20
CLOSE, IV-20
IMAGE, IV-20
MODE, IV-20
MPUT, IV-19
OPEN, IV-20
PUT, IV-19
QUIT, IV-20
SEND, IV-19
STRU, IV-20
TYPE, IV-20
FTP Troubleshooting, IV-49 to
IV-55
G
GET Community Name
(TCP/IP), IV-31
Gleaning, Assigning an IP
Address, IV-9
H
HP-UX v10.xx Application
prerequisites, IV-67
procedure, IV-68
HP-UX v8.07 Application
prerequisites, IV-63 to IV-64
procedure, IV-64 to IV-66
HP-UX v9.xx Application
Prerequisites, IV-67
procedure, IV-68 to IV-69
I
IBM AIX ver. 3.x Application
prerequisites, IV-75
procedure, IV-75 to IV-77