Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
IX - 2
Section 9 - Regulatory Information
OKI OkiLAN 6020e User’s Guide
Federal Communications
Commission Radio Frequency
Interference Statement
This equipment generates and uses radio frequency
energy. If not installed and used according to the
manufacturer’s instructions, this equipment may
cause interference with radio/TV reception.
The Federal Communications Commission has
established technical standards regarding radio
frequency energy emitted by computing devices.
This equipment complies with Part 15 of the FCC
Rules, subject to the following conditions: This
device may not cause harmful interference; and it
must accept any interference received, including
interference that may cause undesired operation.
There is no guaranteed that interference will not
occur in a particular installation. If you suspect that
this equipment is interfering with radio/TV reception
try the following:
• While observing the interference, turn the suspect
equipment off and back on. If the inteference
stops when you turn the equipment off , and
starts again when you turn the equipment on, the
equipment is probably the source of your
problem.
• Connect the equipment and the receiver to
different electrical outlets.
• Increase the distance between the equipment and
the receiver.
• Reorient or relocate the receiving antenna.
• Consult your dealer or an experienced radio/TV
technician for additional advice.
OKI is not responsible for radio/TV interference
caused b using unauthorized cables or by making
unauthorized changes to this equipment.