Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
VII - 10
Section 7 - Chapter 2 - OkiLAN 6020e Setup for Windows 95/98
OKI OkiLAN 6020e User’s Guide
Chapter 2
OkiLAN 6020e Set Up for
Windows 95/98
Overview
This section contains instruction and information on
how to set up your OkiLAN 6020e for a Windows 95/
98 environment. Print options for Windows 95/98
include:
• OkiLAN 6020e Connect for TCP/IP
• OkiLAN 6020e Connect for DLC
• OkiLAN 6020e Connect for IPX/SPX
OkiLAN 6020e Connect for TCP/IP
OkiLAN 6020e Connect for TCP/IP is a full featured
utility that allows simple, direct, TCP/IP printing from
your computer to a printer attached to an OKI TCP/IP
enabled print server. With OkiLAN 6020e Connect,
you can even print to print servers using Dynamic IP
addresses (DHCP). Print jobs printed through OkiLAN
6020e Connect are sent directly to the OkiLAN 6020e
print server and not routed through the network server,
resulting in a reduction of network traffic.
System Requirements
To use OkiLAN 6020e Connect for TCP/IP, your
operating system must be Windows 95/98 and your
computer must be configured to run TCP/IP. The
OkiLAN 6020e print server must also be configured to
run TCP/IP.
Installation
To install OkiLAN 6020e Connect for TCP/IP:
1. Install the OkiLAN 6020e Connect for TCP/IP-see
Section I.
2. When installation is complete, click on Start,
Settings and then Printers.