Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
VII - 6
Section 7 - Chapter 1 - OkiLAN 6020e Setup for Windows NT
OKI OkiLAN 6020e User’s Guide
Notify When Printed
This feature will provide an alert when your job is
active on the printer. This may be useful if the printer is
especially busy.
Description
An optional field where you may list the location or
other useful information about the printer port.
OkiLAN 6020e Connect for DLC
OkiLAN 6020e Connect for Data-Link Control (DLC)
provides a direct printing solution for users in
Microsoft Windows NT serverless environments with
the DLC/LLC protocol. Print jobs printed through
OkiLAN 6020e Connect are sent directly to the
OkiLAN 6020e print server and not routed through the
network server, resulting in a reduction of network
traffic. OkiLAN 6020e Connect for DLC can be used to
configure the print server, obtain status from the print
server and printer, and send jobs to the printer.
Note: To obtain a version of OkiLAN 6020e Connect
for DLC that supports Windows NT, visit our
FTP site (ftp://ftp.extendsys.com/pub/
printserver/utilities/) or contact Technical
Support.
Configure Port
If you have printing problems while using the OkiLAN
6020e Connect printing port, you may check the status
of the port by selecting Configure Port under the Ports
tab in the Properties screen.
Notify On Printer Error
This feature will check the printer status prior to
printing the job. If a printer error is detected (e.g.
printer off-line or out of paper) the error description
will be given.