Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
VII - 3
Section 7 - Chapter 1 - OkiLAN 6020e Setup for Windows NT
OKI OkiLAN 6020e User’s Guide
Windows Printing
Chapter 1
OkiLAN 6020e Set Up for
Windows NT 4.0/2000
Overview
This section contains instruction and information on
how to set up your OkiLAN 6020e for a Windows NT
4.0/2000 environment. Print options for Windows NT
4.0/2000 include:
• OkiLAN 6020e Connect for IP
• OkiLAN 6020e Connect for DLC
• LPR
OkiLAN 6020e Connect for IP
OkiLAN 6020e Connect for TCP/IP is a full featured
utility that allows simple, direct, TCP/IP printing from
your computer to a printer attached to an OKI TCP/IP
enabled print server. OkiLAN 6020e Connect has
advantages over other TCP/IP printing options. It
allows you to print to print servers that are using
Dynamic IP addresses (DHCP). It will also notify you
immediately in the event of a printer error (e.g. Paper
out). Print jobs printed through OkiLAN 6020e
Connect are sent directly to the OkiLAN 6020e print
server and not routed through a network server,
resulting in a reduction of network traffic.
System Requirements
To use OkiLAN 6020e Connect for TCP/IP for your
Windows NT 4.0/2000 operating system, your
computer must be configured to run TCP/IP. The
OkiLAN 6020e print server must also be configured to
run TCP/IP.