Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
VI - 12
Section 6 - Appendix A - Troubleshooting
OKI OkiLAN 6020e User’s Guide
Message: No OkiLAN 6020e device(s) found. Verify the
OkiLAN 6020e is powered on.
Recommended Action: Confirm the device is powered
on and the LED is green. Verify correct zone to search
by printing a configuration sheet.
Message: Option is not available with this product.
Recommended Action: This configuration option is
not available with this product.
Message: Only the first 1024 zones found will be
displayed.
Recommended Action: Reduce the number of zones
on your network.
Message: Router zone requested failed.
Recommended Action: The OkiLAN 6020e utility is
unable to communicate with the router and to locate the
zones. Confirm proper router operation.
Message: The change could not be verified.
Recommended Action: The change will take place
when the OkiLAN 6020e is idle. If it is power cycled or
reset before it becomes idle, changes will be lost.
Return to the zone selection window and search the
network again to display the new information.
Message: There is not enough memory to perform the
requested action.
Recommended Action: Closing windows or quitting
application programs on the Macintosh can make more
memory available.
Message: This option is not valid while the port is
disabled. Enable the port before using this option.
Recommended Action: Cannot reconfigure the device
while the port is disabled.
Message: Unexpected AppleTalk error.
Recommended Action: Check the network connection.
Try again.