Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
VI - 11
Section 6 - Appendix A - Troubleshooting
OKI OkiLAN 6020e User’s Guide
EtherTalk
• Compare the zone in which the OkiLAN 6020e
appears in the Chooser to the zones searched. Search
the same zone where the OkiLAN 6020e appears in
the Chooser.
OkiLAN 6020e Utility Errors
Message: AppleTalk network is inaccessible.
Recommended Action: Examine network connections
and verify AppleTalk is active in the Chooser.
Message: Device limit exceeded. First 100 devices will
be shown.
Recommended Action: There are a maximum of 100
devices. Reduce the number of zones you are searching
and try again.
Message: Device returned invalid local zone list.
Recommended Action: Verify proper router operation.
Message: Incompatible version of OkiLAN 6020e
utility.
Recommended Action: Call 1-800-OKI-DATA
(1-800-654-3282).
Message: NBP Lookup Error.
Recommended Action: Try again.
Message: “Name” @ “Zone” is busy.
Recommended Action: Unable to change the
configuration at this time. Try again.
Message: “Name” @ “Zone” is not responding. Verify
the OkiLAN 6020e is powered on. To reconnect with the
device, return the zone selection window and search
again.
Recommended Action: The device did not respond. If
a reset has just taken place, the OkiLAN 6020e may not
be registered on the network yet. Verify the OkiLAN
6020e is powered on. Search the network again to find
the device.