Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
VI - 7
Section 6 - Chapter 2 - The OkiLAN 6020e Utility
OKI OkiLAN 6020e User’s Guide
EtherTalk
Enable Port
This option allows you to enable or disable a port. If a
port is disabled, it will appear in the OkiLAN 6020e
utility but will not appear in the Chooser. A disabled
port cannot be configured. The only valid options for a
disabled port are Status, Enable Port, Print Config, and
Restore Defaults. A port should be disabled when no
printer is attached.
Note: It is possible to disable all ports but this is not
recommended. The EtherTalk protocol will still
be active on the network. To disable the
EtherTalk protocol, use a utility from one of the
other protocols.
Reset Board
This option will reset the print server.
Restore Defaults
This option will automatically return the EtherTalk
interface to its factory defaults. All ports will be
restored to factory defaults.
The following OkiLAN 6020e variables will restore to
default:
Name: OKI <serial number> Port <port number>
(for single port products, the port number will not
be shown)
Type 1 = LaserWriter
Type 2 = (None)
Zone = Default - (The default zone for the network
segment will be used)
Port Enabled = Yes