Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
VI - 6
Section 6 - Chapter 2 - The OkiLAN 6020e Utility
OKI OkiLAN 6020e User’s Guide
Print Configuration
The Print Configuration option is accessed by selecting
Print Config from the File pull-down menu. Choose
this option to print an OkiLAN 6020e configuration
sheet. A configuration sheet will print to all output
ports.
Status
The Status option is accessed by selecting Status from
the File pull-down menu. This option displays the
status and EtherTalk configuration of the selected
OkiLAN 6020e printer.
Advanced Configuration Options
The following configuration options are advanced
features of the OkiLAN 6020e utility. Most users will
not need to access these features. Read the folloiwng
descriptions carefully before utilizing these options.
Set Type
The Set Type option is accessed by selecting Type from
the Configure pull-down menu. This option allows you
to configure the AppleTalk Type. For some print
spoolers to work properly, the AppleTalk Type must be
changed. Refer to Appendix C of this section for more
information.
The default AppleTalk Type is LaserWriter. For most
printer drivers, this setting should not be changed. This
includes the LaserWriter Drivers, HP LaserJet Drivers
and other drivers.
Each EtherTalk printer port supports two AppleTalk
Types:
• Type1 (mandatory) - The Type 1 default is
LaserWriter. This option should not be changed
unless the user wishes to use a print spooler without
bypass or the user does not want the printer to
respond to any of the LaserWriter drivers.
• Type 2 (optional) - Select this option when
configuring for a spooler.