Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
VI - 5
Section 6 - Chapter 2 - The OkiLAN 6020e Utility
OKI OkiLAN 6020e User’s Guide
EtherTalk
Renaming the OkiLAN 6020e Printer
The OkiLAN 6020e Printer Selection window contains
a list of all OkiLAN 6020e printers found in the
selected zones. OkiLAN 6020e printers are listed
alphabetically by name. Each port of a multiport
OkiLAN 6020e will appear separately in the list.
Unless otherwise stated, changing a configuration
option will affect only the selected port.
1. Choose the OkiLAN 6020e printer you wish to
rename.
2. Select Name from the Configure pull-down menu.
3. Enter a name for the OkiLAN 6020e. If you choose
a name that is already being used, the OkiLAN
6020e will append a number to the end of the name.
Names can be a maximum of 32 characters long.
4. Click Rename. You will then be returned to the
Printer Selection window.
Note: The options listed on the following pages can
all be accessed from the Printer Selection
window.
Selecting a Zone
1. Choose the OkiLAN 6020e printer you wish to
rezone.
2. Select Zone from the Configure pull-down menu.
3. Choose the zone in which you want the printer to
appear.
Note: If no Phase 2 router was found, this option will
be unavailable.
4. Click OK.