Printer User Manual
Table Of Contents
- 6020e_4.pdf
- In This Section
- Chapter 1Introduction
- Overview
- Software Requirements
- Network Preparation
- Before You Start
- Overview of TCP/IP Configuration
- Chapter 2 Configuring the OkiLAN 6020e
- Choosing an IP Address
- Configuring the OkiLAN 6020e
- Assigning the IP Address
- Other Utilities
- Verifying Access to the OkiLAN 6020e
- Chapter 3 TCP/IP Configuration and Printing
- Overview
- Configuring for TCP/IP Network Printing
- Remote Print Queue Name
- Configuring a BSD-Style Print Queue
- Remote LPD Printing
- FTP Printing
- Timeout Checking
- Raw Port Printing
- Chapter 4 OkiNet for TCP/IP
- Overview
- System Requirements
- Running OkiNet for TCP/IP
- Configuring the OkiLAN 6020e Using OkiNet for TCP/IP
- Configuring TCP/IP Options
- EtherTalk Configuration Options
- Output Port Configuration Options
- SNMP Configuration Options
- Enabling/Disabling Protocols
- SNMP Trap Configuration
- Saving the Configuration
- Displaying OkiLAN 6020e Diagnostic Information
- Printing a Configuration Sheet
- Resetting the OkiLAN 6020e
- Restoring Factory Default Settings
- Creating Customized Views
- Modifying View Settings
- Permanently Defining SNMP Access Information
- Configuring the Discovery UDP Port Number
- Starting a Telnet Session
- Starting the BOOTP Server
- Chapter 5 Web Configuration
- Chapter 6 Telnet Configuration
- Overview
- Running a Telnet Session
- Appendix A Troubleshooting
- Main Status Indicator
- Restoring the OkiLAN 6020e to Factory Defaults
- Unable to Assign IP Address
- Hardware Error Messages
- Printing a Configuration Page
- Unable to Print
- Appendix B Application Considerations
- Overview
- Assigning the OkiLAN 6020e IP Address with BOOTP
- Configuring the OkiLAN 6020e IP Address with RARP
- Configuring HP-UX v8.07 for Printing with the OkiLAN 6020e
- Configuring HP-UX v9.xx for Printing with the OkiLAN 6020e
- Configuring HP-UX v10.xx for Printing with the OkiLAN 6020e
- Configuring SCO UNIX for Printing with the OkiLAN 6020e
- IBM's AIX ver. 3.x for Printing with the OkiLAN 6020e
- Configuring Solaris 2.x for Printing with the OkiLAN 6020e
- Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing with the OkiLAN 6020e
- Appendix C Internet Printing Protocol (IPP)
V - 7
Section 5 - Chapter 2 - Installation
OKI OkiLAN 6020e User’s Guide
LAN Manager/ Server
Running INSTALL
1. Login to the server with administrator privileges.
If you are reinstalling the utility, disable the spooler
before running install. If this is the first time you
have installed the utility, disabling the spooler is
optional.
2. From the OS/2 command line, change to the OS/2
directory.
3. Check the README file for current installation
notes.
4. Type INSTALL and press Enter.
5. Verify the install directories are correct.
6. Select INSTALL to proceed. When the utilities are
installed, you will see a message indicating that the
installation was successful.
If the install was not successful read through the
comments in the Install Progress window for errors
and recommended action.
7. Select Exit.
Completing the Installation
After the OKI software has been installed, you must do
the following:
1. Verify the OS/2 spooler is enabled.
2. Verify /OS2/DLL is first in the LIBPATH statement
in the CONFIG.SYS file.
3. Shut down and restart the OS/2 file server.
4. Run the OkiNet for OS/2 utility to add local ports.
Running OkiNet for OS/2
Before you can print via the OkiLAN 6020e, you must
first add a local printer port to your OS/2 server.
1. Select the Network Printing Tools folder on the
OS/2 desktop or in the Desktop Manager.
2. Select the OkiNet for OS/2 utility icon.